i
Brakes India
Filter interviews by
Clear (1)
I gained practical experience through internships and projects during my studies.
Completed internships at XYZ Company and ABC Company
Worked on a project to optimize production processes at university
Applied theoretical knowledge in real-world scenarios
Pressure is the force applied perpendicular to the surface of an object per unit area.
Pressure is measured in units such as Pascals (Pa) or pounds per square inch (psi).
Pressure can be calculated using the formula: Pressure = Force / Area.
Examples of pressure include atmospheric pressure, water pressure, and blood pressure.
I applied via Naukri.com and was interviewed in Sep 2021. There were 2 interview rounds.
I applied via Naukri.com and was interviewed in Sep 2021. There was 1 interview round.
Production details can be managed through proper planning, documentation, and communication.
Create a production plan that outlines the process and timeline
Document all production details including materials, equipment, and personnel
Communicate regularly with team members to ensure everyone is on the same page
Use technology such as production management software to streamline processes
Regularly review and analyze produc
Brakes India interview questions for designations
I applied via Recruitment Consultant and was interviewed in Apr 2021. There was 1 interview round.
Pressure is the force exerted on a surface per unit area.
Pressure is a measure of how much force is applied to a given area.
It is calculated by dividing the force applied by the area over which it is distributed.
Pressure can be expressed in various units such as pascals, pounds per square inch (psi), or atmospheres.
Examples of pressure include the air pressure in a tire, the water pressure in a pipe, or the blood press
Strain is the measure of deformation or elongation of a material under stress.
Strain is a ratio of change in length to the original length of a material.
It is measured in units of percentage or in terms of length per unit length.
Strain can be either tensile (stretching) or compressive (shrinking).
Force is a physical quantity that describes the interaction between two objects.
Force is measured in Newtons (N)
It can be calculated using the formula F = m x a (force = mass x acceleration)
There are different types of forces such as gravitational, electromagnetic, and frictional forces
Force can cause an object to accelerate, change direction, or deform
Top trending discussions
I applied via Campus Placement and was interviewed before May 2020. There was 1 interview round.
I was interviewed in Jul 2017.
I was interviewed in Dec 2016.
A two-stroke engine completes a power cycle in two strokes of the piston, while a four-stroke engine completes it in four strokes.
Two-stroke engines have a simpler design and are lighter than four-stroke engines.
Two-stroke engines have a higher power-to-weight ratio but lower fuel efficiency compared to four-stroke engines.
Four-stroke engines have separate intake, compression, power, and exhaust strokes, while two-stro...
A pictorial representation of a SI engine with valve opening, TDC, and BDC.
SI engine stands for Spark Ignition engine, which is commonly used in gasoline-powered vehicles.
Valve opening refers to the movement of the intake and exhaust valves to allow fuel-air mixture in and exhaust gases out of the combustion chamber.
TDC (Top Dead Center) is the position of the piston at the extreme top of its stroke.
BDC (Bottom Dead Ce...
I would improve the fuel efficiency of TVS motorcycles by implementing advanced engine technology.
Implementing electronic fuel injection system for better fuel management
Introducing hybrid technology for improved mileage
Optimizing aerodynamics of the motorcycle for reduced drag
Using lightweight materials for better fuel economy
I am a dedicated production engineer with a strong background in manufacturing processes and quality control.
Graduated with a degree in Mechanical Engineering
Experience working in a manufacturing plant for 3 years
Proficient in CAD software for designing production layouts
Implemented lean manufacturing principles to improve efficiency
Led a team in reducing production downtime by 20%
I applied via Walk-in and was interviewed in Mar 2024. There was 1 interview round.
based on 2 interviews
Interview experience
based on 29 reviews
Rating in categories
Trainee
275
salaries
| ₹0 L/yr - ₹0 L/yr |
Engineer
222
salaries
| ₹0 L/yr - ₹0 L/yr |
Junior Engineer
204
salaries
| ₹0 L/yr - ₹0 L/yr |
Senior Engineer
167
salaries
| ₹0 L/yr - ₹0 L/yr |
Deputy Engineer
150
salaries
| ₹0 L/yr - ₹0 L/yr |
Bosch
TVS Motor
Mahindra & Mahindra
Tata Motors