10+ Yuvan Logistics Interview Questions and Answers

Consult with a supervisor to determine the best course of action.

• Consult with a supervisor or team leader for guidance.

• Consider the urgency of the situation and potential risks of using the product without proper filtration.

• Check if there are any alternative filters or ways to bypass the pre-filters temporarily.

• Communicate with relevant stakeholders about the issue and potential solutions.

• Document the decision-making process and actions taken for future reference.

Raw material and packing material are received through a structured procedure to ensure quality and traceability.

• Raw material and packing material are typically received at a designated receiving area in the warehouse.

• Upon arrival, the materials are checked against the purchase order to ensure accuracy.

• Quality checks may be performed to verify the condition and specifications of the materials.

• The materials are then labeled, stored in designated areas, and logged into the inve...read more

While receiving any active material, I check for authenticity, expiration date, quantity, and quality.

• Check for authenticity of the material to ensure it is not counterfeit

• Verify the expiration date to ensure it is safe for use

• Confirm the quantity received matches the order

• Inspect the quality of the material for any defects or damage

I would immediately stop dispensing, contain the spillage, clean it up following proper protocols, and report the incident to the appropriate personnel.

• Stop dispensing immediately to prevent further spillage

• Contain the spillage using appropriate materials such as absorbent pads or spill kits

• Clean up the spillage following proper protocols and safety measures

• Report the incident to the appropriate personnel for further action

• Ensure to document the spillage and cleanup process f...read more

Dew point is the temperature at which air becomes saturated with water vapor and starts to condense into liquid water.

• Dew point is a measure of humidity in the air.

• It is the temperature at which dew forms on surfaces.

• When the air temperature drops to the dew point, fog or dew may form.

• Dew point is important in weather forecasting as it indicates the likelihood of precipitation.

• A higher dew point means there is more moisture in the air.

Yes, QMS stands for Quality Management System which is a set of policies, processes, and procedures required for planning and execution in the core business area of an organization.

• QMS is a system that helps organizations ensure they meet customer and regulatory requirements in terms of quality.

• It involves processes for quality planning, quality control, quality assurance, and quality improvement.

• Examples of QMS include ISO 9001 certification and Six Sigma methodologies.

The critical parameter in granulation is the moisture content of the granules.

• Moisture content affects the flowability and compressibility of the granules.

• Optimal moisture content is necessary for proper granule formation.

• Excessive moisture can lead to sticking and clogging in the granulation process.

• Insufficient moisture can result in poor granule strength and friability.

• Examples: Wet granulation requires higher moisture content compared to dry granulation.

SFM sensor sensitivity refers to the ability of the sensor to detect small changes in the input signal.

• SFM sensor sensitivity is typically measured in terms of the smallest detectable change in the input signal that the sensor can accurately measure.

• Higher sensor sensitivity means the sensor can detect smaller changes in the input signal.

• For example, a sensor with high sensitivity may be able to detect minute changes in temperature or pressure.

• Sensor sensitivity is an importa...read more

Critical quality attributes are the key physical, chemical, biological, or microbiological properties or characteristics that must be within an appropriate limit, range, or distribution to ensure the desired product quality.

• Critical quality attributes are essential characteristics of a product that directly impact its safety, efficacy, and quality.

• They are determined based on the intended use of the product and regulatory requirements.

• Examples include potency, purity, identit...read more

Creep speed refers to the slow and steady movement of a production process or project.

• Creep speed is often used in project management to describe the gradual progress of a project.

• It can also refer to the slow movement of machinery or equipment in a manufacturing setting.

• Creep speed helps ensure precision and accuracy in tasks that require careful attention to detail.

To revise a document, review it for errors, clarity, and consistency.

• Read through the document multiple times

• Check for spelling and grammar errors

• Ensure the document is clear and concise

• Verify that the document is consistent in formatting and style

• Ask a colleague to review the document for a fresh perspective

Ducts are typically cleaned by using specialized equipment to remove dust, debris, and other contaminants.

• Use specialized equipment such as high-powered vacuums and brushes to clean the ducts thoroughly

• Inspect the ducts for any signs of damage or leaks that may need repair

• Ensure proper sealing of duct connections to prevent air leaks and improve efficiency

Principle FBD stands for Free Body Diagram, a visual representation of forces acting on an object.

• FBD is a diagram used in physics to show all the forces acting on an object without any other objects in the system.

• It helps in analyzing the motion of the object and determining the net force acting on it.

• Common forces shown in FBD include gravity, normal force, friction, tension, and applied forces.

• FBDs are often used in engineering, mechanics, and physics to solve problems inv...read more