Filter interviews by
Clear (1)
I applied via Campus Placement and was interviewed in May 2021. There were 3 interview rounds.
I applied via Walk-in and was interviewed in Jul 2020. There were 4 interview rounds.
Top trending discussions
posted on 10 Jul 2017
I was interviewed in Aug 2016.
I am a recent graduate with a degree in Mechanical Engineering and a passion for problem-solving and innovation.
Graduated with a degree in Mechanical Engineering
Passionate about problem-solving and innovation
Completed internships at XYZ Company and ABC Company
Led a team project on designing a new prototype for a car engine
Vapour compression refrigeration cycle is a process used in refrigeration systems to remove heat from a space and maintain a cool temperature.
Vapour compression refrigeration cycle is based on the principle of phase change of a refrigerant.
The cycle consists of four main components: compressor, condenser, expansion valve, and evaporator.
The refrigerant enters the compressor as a low-pressure vapor and is compressed to ...
The differential is a device that allows the wheels of a vehicle to rotate at different speeds while maintaining traction.
The differential is located in the center of the axle and is connected to the drive shaft.
It consists of a set of gears that distribute power from the engine to the wheels.
The main function of the differential is to allow the wheels to rotate at different speeds, especially when turning.
When a vehic...
The propeller shaft is a component in an automobile that transmits power from the transmission to the differential.
It is a long, cylindrical shaft made of steel or aluminum.
It connects the transmission output shaft to the differential input shaft.
It allows the power generated by the engine to be transferred to the wheels.
It is commonly used in rear-wheel drive vehicles.
In four-wheel drive vehicles, there are usually tw...
The number of joints in a propeller shaft depends on the design and type of the shaft.
The number of joints can vary depending on the length and complexity of the propeller shaft.
A typical propeller shaft may have one or two joints.
Some propeller shafts may have more joints if they are designed for flexibility or to accommodate changes in length.
The joints in a propeller shaft are usually universal joints or constant ve...
Universal joints are mechanical devices used to connect two shafts that are not in line with each other.
Universal joints are also known as U-joints or Cardan joints.
They are commonly used in automotive applications to transmit power from the engine to the wheels.
Universal joints allow for the transmission of rotational motion at different angles and speeds.
They consist of a cross-shaped component with needle bearings a...
The gears used in a differential are bevel gears and pinion gears.
Bevel gears are used to transfer power from the drive shaft to the differential housing.
Pinion gears are used to transfer power from the differential housing to the axle shafts.
The bevel gears and pinion gears work together to allow the wheels to rotate at different speeds while maintaining power distribution.
The bevel gears are typically spiral bevel ge...
The boiling point of a substance decreases with decreasing pressure in a vacuum.
Boiling point is the temperature at which a substance changes from a liquid to a gas.
In a vacuum, the pressure is significantly lower than atmospheric pressure.
Lower pressure in a vacuum reduces the intermolecular forces holding the substance together.
As a result, less energy is required to overcome these forces and the boiling point decrea...
One tonnage of refrigeration is equal to approximately 3.5169 kilowatts (KW).
One ton of refrigeration is the amount of heat required to melt one ton (2000 pounds) of ice in 24 hours.
It is a unit used to measure the cooling capacity of refrigeration systems.
The conversion factor from tonnage of refrigeration to KW is approximately 3.5169.
To convert tonnage of refrigeration to KW, multiply the tonnage by 3.5169.
There are several types of heat exchangers, including shell and tube, plate, and finned tube heat exchangers.
Shell and tube heat exchangers consist of a shell with multiple tubes inside, allowing for efficient heat transfer.
Plate heat exchangers use a series of plates to separate the hot and cold fluids, maximizing heat transfer surface area.
Finned tube heat exchangers have fins attached to the tubes, increasing the he...
There are 2.54 centimeters in one inch.
1 inch is equal to 2.54 centimeters.
The conversion factor between inches and centimeters is 2.54.
To convert inches to centimeters, multiply the number of inches by 2.54.
To convert centimeters to inches, divide the number of centimeters by 2.54.
posted on 14 Jan 2015
posted on 14 Mar 2015
posted on 27 Mar 2015
posted on 30 Mar 2015
The unit operations used in the plant during summer training.
Distillation
Filtration
Crystallization
Extraction
Drying
Mixing
Heat transfer coefficient changes with baffle spacing in heat exchangers. Other important factors include fluid properties, flow rate, and surface roughness.
Heat transfer coefficient increases with decreasing baffle spacing
Fluid properties such as viscosity and thermal conductivity affect heat transfer
Higher flow rates can increase heat transfer coefficient
Surface roughness can affect heat transfer by creating turbulen
Viscosity Index of lube measures its resistance to change in viscosity with temperature.
Viscosity Index (VI) is an important property of lubricating oils.
It measures the oil's ability to maintain its viscosity under different temperature conditions.
Higher VI means the oil's viscosity changes less with temperature, indicating better performance.
VI is calculated using kinematic viscosity measurements at two different tem...
Different kinds of distillation include simple distillation, fractional distillation, steam distillation, and vacuum distillation.
Simple distillation is used to separate liquids with different boiling points.
Fractional distillation is used to separate liquids with similar boiling points.
Steam distillation is used to extract essential oils from plants.
Vacuum distillation is used to separate liquids with high boiling poi...
Factors to consider for checking evaporator efficiency
Temperature difference between inlet and outlet air
Airflow rate
Refrigerant flow rate
Frost buildup on evaporator coils
Cleanliness of evaporator coils
Type of refrigerant used
I am a highly motivated individual with a passion for learning and a strong work ethic.
I have a Bachelor's degree in Computer Science
I have completed several internships in software development
I am proficient in multiple programming languages including Java and Python
I enjoy working in a team environment and collaborating on projects
I am always looking for new challenges and opportunities to grow
Gujarat offers a rich cultural heritage, diverse cuisine, and a thriving business environment.
Gujarat is home to several UNESCO World Heritage Sites such as the Rani ki Vav stepwell and the Champaner-Pavagadh Archaeological Park.
The state is known for its delicious cuisine, including dishes like dhokla, thepla, and fafda.
Gujarat has a strong economy, with a focus on industries such as textiles, chemicals, and pharmaceu...
Yes, I believe I can inspire others through my actions and words.
I have a positive attitude and outlook on life
I am passionate about my work and hobbies
I enjoy helping others and sharing my knowledge and experiences
I have received positive feedback and recognition for my leadership and motivational skills
I have the skills, experience, and passion to excel in this role.
I have a proven track record of success in similar roles.
I am highly motivated and dedicated to achieving results.
I have excellent communication and interpersonal skills.
I am a quick learner and adaptable to new situations.
I am passionate about this industry and eager to contribute my expertise.
I am confident that I can make a valuable contribution to you
posted on 3 Apr 2015
Gibbs free energy is called free energy because it is the energy available to do work at constant temperature and pressure.
Gibbs free energy is the maximum amount of work that can be obtained from a system at constant temperature and pressure.
It takes into account both the enthalpy and entropy of a system.
If the Gibbs free energy is negative, the reaction is spontaneous and can do work.
Examples include the combustion o...
Maxwell's equations describe the behavior of electromagnetic fields.
There are four equations: Gauss's law, Gauss's law for magnetism, Faraday's law, and Ampere's law with Maxwell's addition.
Together, these equations explain how electric and magnetic fields interact and propagate through space.
Maxwell's equations are fundamental to the study of electromagnetism and have many practical applications, such as in the design...
Designing of Distillation Column
Determine the desired separation
Select the appropriate column type
Calculate the number of theoretical plates
Determine the feed location and reflux ratio
Design the reboiler and condenser
Select appropriate materials of construction
Consider safety and environmental factors
posted on 14 Jan 2015
posted on 17 Jan 2015
based on 4 reviews
Rating in categories
Assistant Engineer
389
salaries
| ₹0 L/yr - ₹0 L/yr |
Deputy Engineer
108
salaries
| ₹0 L/yr - ₹0 L/yr |
Assistant Manager
85
salaries
| ₹0 L/yr - ₹0 L/yr |
Engineer
70
salaries
| ₹0 L/yr - ₹0 L/yr |
Service Engineer
68
salaries
| ₹0 L/yr - ₹0 L/yr |
Exide Industries
Tata Power
BHEL
Hindustan Unilever