Filter interviews by
Tools required for motor alignment include laser alignment tools, dial indicators, feeler gauges, and alignment bars.
Laser alignment tools are used to ensure precise alignment of the motor shafts.
Dial indicators are used to measure the runout of the motor shafts.
Feeler gauges are used to check the clearance between the motor and the mounting base.
Alignment bars are used to ensure parallel alignment of the motor shafts.
...
Bearing clearance can be measured using a feeler gauge tool.
Use a feeler gauge tool to measure the gap between the bearing and the shaft.
Insert the feeler gauge between the bearing and the shaft to determine the clearance.
Ensure the bearing is properly seated and the shaft is not moving during measurement.
Master level is used in various aspects of millwright work, such as precision measurements, equipment installation, and troubleshooting.
Master level is used for precision measurements to ensure equipment is properly aligned and leveled.
Master level is used during equipment installation to ensure everything is set up correctly.
Master level is used for troubleshooting to identify any issues with alignment or leveling tha
The accuracy of a micrometer typically ranges from 0.001mm to 0.0001mm.
Micrometers are commonly accurate to within 0.001mm (1 micrometer) or even 0.0001mm (0.1 micrometer).
The accuracy can vary depending on the quality and calibration of the specific micrometer.
For precision measurements, a micrometer with higher accuracy is preferred.
Motor alignment is the process of ensuring that the motor shaft is properly aligned with the driven equipment shaft to prevent issues like vibration and premature wear.
Motor alignment involves using precision tools like dial indicators and laser alignment systems to measure and adjust the position of the motor shaft.
Proper alignment helps in reducing energy consumption, increasing equipment lifespan, and improving over...
Top trending discussions
The number of days required for alignment of girth gear depends on various factors.
The number of days required for alignment of girth gear depends on the size and complexity of the gear.
The experience and skill level of the team performing the alignment also plays a role.
On average, alignment of a girth gear can take anywhere from 2-5 days.
However, larger and more complex gears may take up to 10 days or more.
Regular ma...
Killan bese alignment is a procedure to align two shafts using a dial indicator.
Mount the dial indicator on one shaft and set it to zero.
Rotate the other shaft and note the readings on the dial indicator.
Adjust the alignment until the readings are within the acceptable range.
Repeat the process for multiple points along the shafts.
Check the alignment again after a few hours of operation.
Use shims or other tools to make
I applied via Referral and was interviewed before Dec 2020. There were 4 interview rounds.
I applied via Job Fair and was interviewed in Jun 2022. There were 3 interview rounds.
Hospitality management
I appeared for an interview in Jul 2020.
I applied via Referral and was interviewed before Oct 2020. There were 3 interview rounds.
Maintenance problems and solutions
Equipment breakdowns - regular maintenance checks and repairs
Lack of spare parts - inventory management and ordering in advance
Inefficient processes - process optimization and automation
Safety hazards - regular safety inspections and training
Environmental concerns - proper disposal of hazardous waste
Budget constraints - prioritization and cost-effective solutions
I applied via Naukri.com and was interviewed in Aug 2020. There was 1 interview round.
I applied via Walk-in and was interviewed before Nov 2020. There were 2 interview rounds.
Drawing of starter for star delta and
A Lpbs wiring, load cell colour code connection
Motor overcurrent faults can be caused by various factors.
Overloading
Short circuits
Ground faults
Mechanical binding
Voltage imbalance
Inadequate cooling
Excessive starting
Inadequate wire size
Inadequate protection
Motor design flaws
Electrical faults in motors can include short circuits, open circuits, insulation breakdown, and overloading.
Short circuits occur when there is a direct connection between the motor windings, causing excessive current flow.
Open circuits happen when there is a break in the electrical path, preventing current from flowing.
Insulation breakdown occurs when the insulation material surrounding the motor windings deteriorates...
S1 duty refers to a continuous duty cycle of a motor or machine.
S1 duty means that the motor or machine can run continuously without any rest or cooling breaks.
It is typically used for applications where the load is constant and the motor or machine does not need to be turned off.
Examples of S1 duty applications include conveyor belts, pumps, and fans.
S1 duty is also known as continuous duty.
It is important to ensure t...
I appeared for an interview before Jan 2023.
Technical, English, reasoning
The market potential for the Senior Engineer role is high due to increasing demand for skilled professionals in the industry.
Growing demand for senior engineers in various industries
Increasing adoption of technology and digital transformation
Emerging markets and new opportunities
Expanding job market and career growth prospects
I applied via Naukri.com and was interviewed in Nov 2023. There was 1 interview round.
Packing plant operation involves receiving, sorting, packing, and shipping products efficiently.
Receiving incoming products and materials
Sorting items based on size, weight, or other criteria
Packing items into appropriate containers or packaging materials
Labeling packages with necessary information
Shipping out finished products to customers or distribution centers
based on 1 interview
Interview experience
Associate Manager
190
salaries
| ₹7.8 L/yr - ₹17.4 L/yr |
Senior Engineer
137
salaries
| ₹4.9 L/yr - ₹11.8 L/yr |
Assistant Manager
123
salaries
| ₹6.7 L/yr - ₹14.6 L/yr |
Engineer
93
salaries
| ₹3.2 L/yr - ₹6.8 L/yr |
Manager
90
salaries
| ₹8.8 L/yr - ₹24.5 L/yr |
JK Cement
ACC
Ambuja Cements
Nuvoco Vistas