i
Metso
Filter interviews by
I applied via Company Website and was interviewed in Apr 2022. There was 1 interview round.
Press filter is a device used for separating solids from liquids.
It works by applying pressure to the mixture to force the liquid through a filter media while retaining the solids.
It is commonly used in industries such as chemical, pharmaceutical, and food processing.
Examples of press filters include belt filter press, plate and frame filter press, and rotary vacuum-drum filter.
Press filters are efficient and cost-effe...
To maintain pressure in press filter, ensure proper sealing, check for leaks, and adjust feed rate and pressure settings.
Check for proper sealing of the filter plates and gaskets
Inspect for any leaks in the system and repair them promptly
Adjust the feed rate and pressure settings as per the manufacturer's recommendations
Regularly clean and maintain the filter to prevent clogging and pressure drop
Monitor the pressure ga...
The model of hydraulic cylinder in press filter depends on the specific press filter being used.
The model of hydraulic cylinder can vary depending on the size and capacity of the press filter.
Some common models of hydraulic cylinders used in press filters include tie rod cylinders and welded cylinders.
The specific model of hydraulic cylinder used in a press filter can be determined by consulting the manufacturer's spec...
Roller bearings are commonly used in bogie wheels.
Roller bearings are preferred over plain bearings due to their ability to handle heavy loads and reduce friction.
Tapered roller bearings are commonly used in locomotive bogie wheels.
Cylindrical roller bearings are also used in some bogie wheels.
The type of bearing used depends on the specific application and load requirements.
Top trending discussions
posted on 24 Jul 2021
I applied via Campus Placement and was interviewed in Apr 2024. There were 3 interview rounds.
Ohm's law states that the current flowing through a conductor is directly proportional to the voltage applied across it, and inversely proportional to the resistance of the conductor.
Ohm's law is represented by the formula V = I * R, where V is voltage, I is current, and R is resistance.
It helps in calculating the current flowing through a circuit when the voltage and resistance are known.
It can also be used to determi...
Diploma last semester assignment
I applied via Recruitment Consulltant and was interviewed in Jun 2024. There were 2 interview rounds.
I applied via Referral and was interviewed in Jun 2024. There were 2 interview rounds.
posted on 7 Sep 2024
posted on 14 Jun 2024
Turbine generator work involves converting mechanical energy into electrical energy using steam or water.
Turbine generators use steam or water to rotate a turbine connected to a generator
The rotating turbine spins magnets inside the generator, creating an electric current
The electric current is then transmitted through power lines for use in homes and industries
Causes of hot bearings include lack of lubrication, overloading, misalignment, and contamination.
Lack of lubrication: Insufficient or degraded lubricant can cause increased friction and heat.
Overloading: Excessive load on the bearing can lead to overheating.
Misalignment: Improper alignment of the bearing can cause it to operate under stress and generate heat.
Contamination: Foreign particles or debris in the bearing can
Over-heating of Commutator in a DC motor can be caused by factors like excessive current, poor ventilation, dirty environment, and worn-out brushes.
Excessive current flowing through the motor can cause the commutator to overheat.
Poor ventilation around the motor can lead to inadequate cooling, resulting in overheating.
A dirty environment can cause dust and debris to accumulate on the commutator, hindering heat dissipat...
The shunt motor will run at dangerously high speeds and may get damaged.
The motor will run at its no-load speed, which is much higher than its rated speed.
This can lead to overheating and mechanical stress on the motor components.
The motor may get damaged or fail prematurely if directly connected to the supply line.
based on 1 interview
Interview experience
based on 11 reviews
Rating in categories
Design Engineer
167
salaries
| ₹3.6 L/yr - ₹11 L/yr |
Assistant Manager
135
salaries
| ₹6.2 L/yr - ₹18.5 L/yr |
Senior Engineer
132
salaries
| ₹5 L/yr - ₹13.5 L/yr |
Engineer
96
salaries
| ₹3 L/yr - ₹11.3 L/yr |
Deputy Manager
70
salaries
| ₹8.4 L/yr - ₹25.8 L/yr |
TK Elevator
Sandvik Asia
FLSmidth
Outotec