M3M India
10+ Lacozy Interview Questions and Answers
Q1. What is standard deviation for M30 grade concrete as IS 456.2000
The standard deviation for M30 grade concrete as per IS 456.2000 is not provided.
The IS 456.2000 code does not specify the standard deviation for M30 grade concrete.
Standard deviation values for concrete grades are typically provided in specific codes or standards.
To determine the standard deviation for M30 grade concrete, one would need to refer to a relevant code or conduct testing.
Without the specific data or code reference, it is not possible to provide an exact standard ...read more
Q2. If we are lapping two different dia bars then lap length shall be according to lower or higher dia ?
The lap length should be according to the higher diameter of the two bars.
The lap length is determined by the larger diameter bar to ensure sufficient overlap and bond strength.
This is because the larger diameter bar requires a longer length to achieve the same level of bond as the smaller diameter bar.
Using the lap length of the larger diameter bar ensures that the connection between the two bars is strong and meets the required standards.
For example, if we are lapping a 12m...read more
Q3. Can we do the welding to reinforcement bars ?
Yes, welding can be done to reinforcement bars.
Welding reinforcement bars is a common practice in construction projects.
It helps to create strong and durable connections between bars.
Welding is often used to join reinforcement bars in concrete structures.
Proper welding techniques and procedures should be followed to ensure quality and safety.
Examples of welding methods for reinforcement bars include shielded metal arc welding (SMAW) and gas metal arc welding (GMAW).
Q4. What is tolerance for cover to reinforcement ?
The tolerance for cover to reinforcement refers to the acceptable variation in the distance between the surface of concrete and the reinforcement bars.
The tolerance for cover to reinforcement is specified in construction codes and standards.
It is important to maintain the specified cover to ensure the durability and strength of the reinforced concrete structure.
The tolerance may vary depending on the type of structure, exposure conditions, and design requirements.
For example,...read more
Q5. %age of fly ash in concrete is allowed by IS 456.2000
The percentage of fly ash allowed in concrete according to IS 456.2000.
IS 456.2000 allows a maximum of 35% fly ash in concrete.
Fly ash is a byproduct of coal combustion and is used as a supplementary cementitious material in concrete.
The use of fly ash in concrete improves workability, durability, and reduces the heat of hydration.
Fly ash can replace a portion of cement in concrete mixtures, reducing the environmental impact.
The specific percentage of fly ash allowed may vary...read more
Q6. Yes. If reinforcement have carbon content equal or less than 0.25%.
The carbon content of reinforcement should be equal to or less than 0.25%.
Reinforcement with carbon content exceeding 0.25% may not meet quality standards.
Carbon content in reinforcement affects its strength and durability.
Examples of reinforcement with low carbon content include low carbon steel bars and fibers.
Testing methods such as carbon analysis can be used to determine the carbon content of reinforcement.
Q7. Non destructive tests of concrete structures ?
Non destructive tests are used to assess the quality and integrity of concrete structures without causing damage.
Ultrasonic testing: Uses high-frequency sound waves to detect flaws or measure the thickness of concrete.
Ground penetrating radar: Uses electromagnetic waves to create images of subsurface structures and detect voids or anomalies.
Impact echo testing: Measures the resonance of a structure by striking it with a hammer and analyzing the resulting sound waves.
Rebound h...read more
Q8. H/4 from top and bottom of column.
H/4 from top and bottom of column refers to the height of the column divided by 4.
H/4 from top and bottom of column is a measurement used in construction and engineering.
It is used to determine the distance from the top and bottom of a column where certain actions or inspections need to take place.
For example, if a column is 12 feet tall, H/4 from top and bottom would be 3 feet from the top and 3 feet from the bottom.
Q9. NO LAP ZONE in column ?
NO LAP ZONE in column refers to a specific area where lap joints are not allowed in the construction of a column.
A lap joint is a type of connection where two pieces of material overlap and are joined together.
In column construction, lap joints are typically avoided in certain zones to ensure structural integrity.
This may be due to factors such as high stress concentration, reduced load-bearing capacity, or increased risk of failure.
Instead of lap joints, alternative methods ...read more
Q10. 4 N/mm2 as per IS 456.2000
4 N/mm2 is the compressive strength of concrete as per IS 456.2000.
IS 456.2000 is the Indian standard code for the design and construction of reinforced concrete structures.
N/mm2 is the unit of measurement for compressive strength of concrete.
Compressive strength refers to the ability of concrete to withstand compression or crushing forces.
4 N/mm2 is a common value used for design purposes in many construction projects.
Q11. Concrete casting manpower requirement
The manpower requirement for concrete casting depends on various factors such as project size, complexity, and timeline.
Manpower requirement for concrete casting is determined by the volume of concrete to be cast.
The complexity of the concrete structure also affects the manpower requirement.
The timeline of the project plays a crucial role in determining the number of workers needed.
Additional factors like the availability of equipment, site conditions, and safety requirements...read more
Q12. One pour area concrete quantity
The quantity of concrete required for one pour area.
Calculate the volume of the pour area by multiplying the length, width, and depth of the area.
Convert the volume to cubic meters or cubic feet depending on the unit of measurement used.
Consider adding a wastage factor to account for any material loss during the pouring process.
Consult the concrete supplier or use a concrete calculator to determine the exact quantity needed.
Example: A pour area with dimensions 5m x 3m x 0.15m...read more
Q13. Project one pour steel quantity
The project requires determining the quantity of steel needed for the first pour.
Calculate the volume of concrete required for the first pour.
Determine the reinforcement ratio for the concrete.
Multiply the volume of concrete by the reinforcement ratio to get the steel quantity.
Consider any additional factors such as wastage or safety margins.
Q14. Plot area sqm2 or sqft.
The question asks for the measurement unit of the plot area.
The question is asking whether the plot area should be measured in square meters or square feet.
The answer should specify the preferred unit of measurement for the plot area.
Examples of possible answers: 'sqm2' for square meters or 'sqft' for square feet.
Q15. Cube tank temperature
The cube tank temperature refers to the temperature inside a cube-shaped tank.
Cube tank temperature is the temperature inside a cube-shaped tank.
It is important to monitor the temperature in cube tanks to ensure optimal conditions for the contents.
The temperature can be controlled through various means such as heating or cooling systems.
Examples of cube tanks include water storage tanks, fermentation tanks, and chemical storage tanks.
Top HR Questions asked in Lacozy
Interview Process at Lacozy
Top Interview Questions from Similar Companies
Reviews
Interviews
Salaries
Users/Month