i
Intertek
Filter interviews by
Valves are mechanical devices used to control the flow of fluids within a system. They can be classified into different types based on their design and function.
Gate valves: used to fully open or close the flow of fluid
Ball valves: have a spherical closure element to control flow
Check valves: allow flow in one direction only to prevent backflow
Butterfly valves: have a disc that rotates to control flow
Pressure relief va...
Defects in welding can compromise the integrity of the joint and lead to structural failures.
Common welding defects include porosity, lack of fusion, cracks, and undercutting.
Porosity is caused by gas entrapment during the welding process.
Lack of fusion occurs when the weld metal fails to fuse with the base metal.
Cracks can result from excessive stress or improper cooling of the weld.
Undercutting is a groove formation ...
The tolerance of UT test refers to the acceptable range of error in the test results.
Tolerance is typically specified in the testing standards or procedures.
It is important to ensure that the equipment used for UT testing is calibrated within the specified tolerance limits.
Deviation from the tolerance range may indicate a need for retesting or further investigation.
Examples of tolerance limits for UT testing may includ
WPS stands for Welding Procedure Specification and PQR stands for Procedure Qualification Record.
WPS is a document that provides detailed welding instructions and parameters for a specific welding job.
PQR is a record of the welding parameters used during the qualification of a welding procedure.
WPS and PQR are essential documents in the welding industry to ensure quality and consistency in welding processes.
Top trending discussions
An inspection engineer is responsible for ensuring the safety, quality, and compliance of equipment, structures, or systems.
Conducting inspections to identify defects or non-compliance
Developing inspection procedures and protocols
Analyzing inspection data and preparing reports
Collaborating with other engineers and stakeholders
Ensuring compliance with regulations and standards
Implementing corrective actions to address i...
I applied via Naukri.com and was interviewed before Jun 2021. There were 2 interview rounds.
Written test about technical details covered ASME CODE
I applied via Referral and was interviewed in Jul 2021. There were 4 interview rounds.
I applied via Recruitment Consulltant and was interviewed in Dec 2022. There were 3 interview rounds.
Mechanical properties refer to the behavior of materials under applied forces, including strength, hardness, elasticity, and toughness.
Mechanical properties include strength, hardness, elasticity, toughness, ductility, and brittleness.
Strength is the ability of a material to withstand an applied force without failure.
Hardness is the resistance of a material to deformation, scratching, or abrasion.
Elasticity is the abil...
Testing processes are essential for ensuring the quality and safety of products or systems.
Testing processes involve conducting various tests to evaluate the performance, reliability, and safety of products or systems.
Types of testing processes include non-destructive testing, destructive testing, visual inspection, and dimensional inspection.
Testing processes help identify defects, weaknesses, or areas for improvement...
PSSR stands for Pre-Startup Safety Review. It is a systematic review of safety aspects before starting up a new or modified process.
Ensures that all safety systems are in place and functioning properly before starting operations
Identifies potential hazards and risks that may arise during startup
Helps in preventing accidents and ensuring the safety of personnel and equipment
Commonly used in industries such as oil and ga...
RT and UT are non-destructive testing methods used in inspection to detect flaws in materials.
RT stands for Radiographic Testing, which uses X-rays or gamma rays to inspect the internal structure of materials.
UT stands for Ultrasonic Testing, which uses high frequency sound waves to detect flaws or measure thickness in materials.
RT is commonly used for detecting internal defects in welds, castings, and forgings.
UT is o...
I applied via Naukri.com and was interviewed in Jul 2021. There were 3 interview rounds.
based on 1 interview
Interview experience
based on 3 reviews
Rating in categories
Inspection Engineer
209
salaries
| ₹2.3 L/yr - ₹9 L/yr |
Lab Technician
164
salaries
| ₹1.8 L/yr - ₹4.3 L/yr |
Quality Engineer
163
salaries
| ₹2 L/yr - ₹7 L/yr |
Chemist
64
salaries
| ₹2 L/yr - ₹5 L/yr |
Assistant Manager
54
salaries
| ₹4.7 L/yr - ₹12 L/yr |
Bureau Veritas
SGS
CMS Infosystems
Medhaj Techno Concept