Filter interviews by
Clear (1)
I applied via Company Website and was interviewed before Dec 2020. There were 4 interview rounds.
The hydraulic pump is responsible for generating the flow of hydraulic fluid in a hydraulic circuit.
The hydraulic pump converts mechanical energy into hydraulic energy.
It creates the pressure needed to move the hydraulic fluid through the circuit.
The pump provides the force necessary to operate hydraulic actuators, such as cylinders or motors.
It ensures the proper functioning of the hydraulic system by maintaining a co...
The standard voltage used in Zambia for boomers is 400 volts.
The standard voltage for boomers in Zambia is 400 volts.
This voltage is commonly used for electrical equipment and machinery.
It is important to ensure that boomers are compatible with this voltage before use.
A capacitor stores electrical energy and releases it when needed.
Capacitors are used to filter out noise and stabilize voltage in power supplies.
They are also used in timing circuits, oscillators, and filters.
Capacitors can be polarized or non-polarized, and have different capacitance values.
They are commonly found in electronic devices such as TVs, radios, and computers.
Top trending discussions
I applied via Referral and was interviewed in Feb 2021. There were 4 interview rounds.
I applied via Walk-in and was interviewed in Nov 2021. There were 2 interview rounds.
Star delta starter is used to reduce the starting current of induction motors.
Reduces the starting current of induction motors
Prevents excessive voltage drop in the power supply
Protects the motor windings from overheating
Allows for smooth and controlled motor starting
Commonly used in applications where high starting torque is not required
The OLTC (On-Load Tap Changer) in a transformer is typically connected to the high voltage side.
OLTC is connected to the high voltage winding of the transformer
It allows for tap changing while the transformer is energized
The low voltage side remains fixed while the high voltage side can be adjusted
Yes, OLTC is always connected in the HT voltage side.
OLTC stands for On-Load Tap Changer.
It is a device used in electrical power transformers to regulate the voltage level.
OLTC is typically connected on the high voltage (HT) side of the transformer.
It allows for tap changing while the transformer is energized and under load.
By changing the tap position, the OLTC can adjust the transformer's output voltage.
This helps to...
UV coil is a component used in HVAC systems to disinfect air by emitting ultraviolet light.
UV coil is installed in the air handling unit of HVAC systems.
It emits ultraviolet light to kill or deactivate microorganisms like bacteria, viruses, and mold spores.
UV light damages the DNA and RNA of these microorganisms, preventing them from reproducing.
UV coil helps improve indoor air quality by reducing the presence of harmf...
UV Coil provides protection against over voltage and under voltage.
UV Coil is a device used in electrical systems to protect against voltage fluctuations.
It monitors the voltage levels and activates when the voltage exceeds or falls below the specified limits.
When the voltage exceeds the upper limit, the UV Coil disconnects the power supply to prevent damage to the equipment.
Similarly, when the voltage falls below the ...
I applied via Company Website
Bukolze relays are used in electrical engineering for their high reliability and ability to handle high voltage and current.
Bukolze relays are known for their robustness and durability.
They are commonly used in power distribution systems and industrial applications.
These relays can handle high voltage and current levels, making them suitable for heavy-duty operations.
They provide reliable switching and protection in el...
Star delta is used in electrical engineering to reduce starting current and protect motors.
Star delta connection is used for induction motors.
It reduces the starting current by a factor of √3.
It helps in reducing voltage drop during motor starting.
It protects the motor from excessive current and overheating.
It is commonly used in applications where the motor needs to start with a low current.
Ten delta test is used to detect winding deformation and shorted turns in transformer.
Detects winding deformation and shorted turns
Helps in identifying internal faults
Used for routine maintenance and troubleshooting
Explosion vent in transformer is used for safety purposes.
It helps to release pressure build-up inside the transformer due to internal faults or external factors.
It prevents the transformer from exploding and causing damage to the surrounding area.
The vent is designed to open at a specific pressure level to ensure safe release of gases.
It is a mandatory safety feature in transformers as per industry standards.
Examples ...
I applied via Approached by Company and was interviewed before Apr 2021. There were 2 interview rounds.
Excellent
I applied via Recruitment Consultant and was interviewed before Oct 2017. There were 3 interview rounds.
The basic hydraulic system consists of various valves and pumps that work together to control fluid flow and pressure.
Valves in a hydraulic system control the direction, flow rate, and pressure of the fluid.
Examples of valves include check valves, relief valves, and control valves.
Pumps in a hydraulic system generate the flow and pressure of the fluid.
Examples of pumps include gear pumps, vane pumps, and piston pumps.
H...
posted on 22 Nov 2015
I applied via Campus Placement
I am a design engineer with experience in creating innovative solutions for complex problems.
I have a degree in mechanical engineering
I have worked on projects ranging from consumer products to industrial machinery
I am skilled in CAD software such as SolidWorks and AutoCAD
I have experience in prototyping and testing designs
I am a creative problem solver and enjoy collaborating with others to find solutions
Yes, I am open to pursuing higher studies.
I believe in continuous learning and upgrading my skills.
Higher studies will provide me with a deeper understanding of my field.
It will also open up new opportunities for career growth.
For example, I may consider pursuing a master's degree in mechanical engineering.
I am willing to balance work and studies to achieve my goals.
I believe that pursuing an MBA is not necessary for my career goals and personal growth.
I have already gained sufficient knowledge and skills through my education and work experience.
I prefer to focus on developing my technical expertise in design engineering.
I am open to pursuing other forms of education or training that align with my interests and goals.
An MBA may not necessarily guarantee career success or advanceme...
My favourite subjects are mathematics, physics, and computer science.
Mathematics: I enjoy solving complex problems and finding patterns.
Physics: I am fascinated by the laws of nature and how they govern the universe.
Computer Science: I love programming and creating new software solutions.
To design a swimming diving board, I will consider the material, dimensions, weight capacity, and safety features.
Choose a durable and non-slip material like fiberglass or aluminum
Determine the appropriate length, width, and thickness based on the intended use and user demographics
Calculate the weight capacity and ensure it can support the maximum weight of a user
Incorporate safety features like a non-slip surface, rou...
posted on 15 Feb 2018
I applied via Approached by Company and was interviewed in Feb 2018. There were 6 interview rounds.
based on 1 review
Rating in categories
Service Engineer
226
salaries
| ₹0 L/yr - ₹0 L/yr |
Design Engineer
148
salaries
| ₹0 L/yr - ₹0 L/yr |
Senior Project Engineer
52
salaries
| ₹0 L/yr - ₹0 L/yr |
Senior Service Engineer
49
salaries
| ₹0 L/yr - ₹0 L/yr |
Technologist
43
salaries
| ₹0 L/yr - ₹0 L/yr |
Sandvik Mining and Rock Technology
Komatsu
Caterpillar Inc
Liebherr