Filter interviews by
I was interviewed before Sep 2022.
Technical questions on mechanical Engineering basics.
Top trending discussions
posted on 24 Feb 2025
I was interviewed in Jan 2025.
Star delta starter is a type of reduced voltage starter used for starting high power motors.
Consists of two contactors - one for star connection and one for delta connection
Reduces starting current and torque to prevent damage to motor windings
Commonly used for motors with high starting current requirements, such as induction motors
Hysteresis loss can be calculated using the area enclosed by the hysteresis loop on a B-H curve.
Calculate the area enclosed by the hysteresis loop on a B-H curve
Use the formula: Hysteresis Loss = ∮B.dH
Consider the material's properties and operating conditions for accurate calculation
Skin effect is the tendency of alternating current to flow near the surface of a conductor, due to self-inductance.
Skin effect is more prominent at higher frequencies.
It causes the effective resistance of the conductor to increase.
Skin effect can be reduced by using hollow conductors or by using stranded conductors.
Example: Skin effect is a common phenomenon in high-frequency transmission lines.
Fluorescent effect is the emission of light by a substance that has absorbed light or other electromagnetic radiation.
Fluorescent effect occurs when a substance absorbs light at a specific wavelength and then re-emits light at a longer wavelength.
Common examples include fluorescent light bulbs, glow-in-the-dark materials, and certain minerals that glow under UV light.
Fluorescent materials can be used in various applica...
In a parallel circuit, components are connected in separate branches, allowing current to flow through multiple paths. In a series circuit, components are connected in a single path, where current flows through each component in sequence.
Parallel circuit allows current to flow through multiple paths, while series circuit has only one path for current.
In a parallel circuit, voltage across each component is the same, whi...
I was interviewed in Dec 2024.
MMC stands for Maximum Material Condition and LMC stands for Least Material Condition. They are used in Geometric Dimensioning and Tolerancing (GD&T) to specify the maximum and minimum limits of a part's dimensions.
MMC is the condition where a part contains the maximum amount of material within the specified limits.
LMC is the condition where a part contains the least amount of material within the specified limits.
F...
Layout inspection is a quality control process to verify dimensions, tolerances, and alignment of components or products.
Ensures components or products are manufactured according to design specifications
Involves measuring dimensions, angles, and alignments using tools like calipers, micrometers, and CMM machines
Helps identify any deviations from the design that may affect product functionality or performance
GD&T stands for Geometric Dimensioning and Tolerancing. It is a system for defining and communicating engineering tolerances.
GD&T is used to specify the allowable variations in form, size, and orientation of part features.
Some common symbols used in GD&T include: Ø for diameter, ⌀ for circular runout, ⊥ for perpendicularity, and ∠ for angularity.
GD&T helps ensure that parts fit together properly and fun...
Selecting the right instrument for dimensional inspection involves considering the accuracy, precision, and type of measurement needed.
Identify the specific dimensions and tolerances that need to be measured
Consider the accuracy and precision required for the inspection
Choose the appropriate instrument based on the type of measurement (e.g. calipers for linear measurements, micrometers for precise measurements)
Ensure t...
GD&T stands for Geometric Dimensioning and Tolerancing. It is a system for defining and communicating engineering tolerances.
GD&T is used to specify the allowable variations in form, size, and orientation of part features.
Symbols used in GD&T include: concentricity, position, profile, runout, perpendicularity, parallelism, etc.
GD&T helps ensure parts are manufactured to the correct dimensions and tolera
Selecting the right instrument for dimensional inspection involves considering accuracy, precision, type of measurement, and calibration.
Understand the specific requirements of the component being inspected
Consider the accuracy and precision needed for the measurements
Choose the appropriate type of instrument (e.g. calipers, micrometers, CMM)
Ensure the instrument is properly calibrated before use
Verify the instrument's...
posted on 29 Jan 2025
I was interviewed in Dec 2024.
posted on 20 Jan 2025
Charger is a device used to supply electrical energy to rechargeable batteries, while Lithium Ion batteries are a type of rechargeable battery commonly used in electronic devices.
Chargers are designed to provide the correct voltage and current to recharge batteries safely.
Lithium Ion batteries are lightweight and have a high energy density, making them popular in portable electronic devices.
Overcharging or using the wr...
Battery swapping technology is a method of quickly replacing a depleted battery with a fully charged one in electric vehicles.
Allows for faster recharging of electric vehicles compared to traditional charging methods
Reduces downtime for electric vehicle drivers
Promotes the use of electric vehicles by addressing range anxiety
Examples: Tesla's battery swap stations, Gogoro's battery swapping network
I applied via Recruitment Consulltant and was interviewed in Jul 2024. There were 2 interview rounds.
A limit switch is a device that is used to detect the presence or absence of an object within a certain range of motion.
Limit switches are commonly used in industrial applications to control machinery and equipment.
They consist of an actuator that is mechanically linked to a set of contacts, which are opened or closed depending on the position of the actuator.
Limit switches can be used to stop the motion of a machine w...
Types of cooling used in dies include water cooling, air cooling, and oil cooling.
Water cooling: uses water to remove heat from the die
Air cooling: uses air to cool the die
Oil cooling: uses oil to dissipate heat from the die
Material and hrc of die parts are crucial for determining the durability and performance of the parts.
Material selection for die parts depends on factors like strength, wear resistance, and thermal conductivity.
Common materials used for die parts include tool steels like H13, D2, and A2.
Hardness of die parts is typically measured using Rockwell Hardness Scale (HRC).
Higher HRC values indicate greater hardness and wear r...
Breakdown in dies on machine can be due to wear and tear, misalignment, overheating, or material defects.
Wear and tear from continuous use can lead to cracks or breakage in the dies.
Misalignment of the dies can cause them to wear unevenly or break prematurely.
Overheating of the dies can weaken their structure and lead to failure during operation.
Material defects in the dies, such as impurities or weak spots, can cause ...
An aptitude test is designed to assess an individual's ability to perform certain tasks or react to a range of different situations. These tests are often used by educational institutions and employers to evaluate potential candidates' skills, talents, and potential for success in a specific role or academic program. Here are some key details about aptitude tests:
1. **Purpose**: Aptitude tests are used to measure a variety of skills, including logical reasoning, verbal ability, numerical skills, and spatial awareness. They help to identify strengths and weaknesses and predict future performance.
2. **Types**:
- **Verbal Reasoning**: Assesses understanding and reasoning using concepts framed in words.
- **Numerical Reasoning**: Tests ability to work with numbers, including basic arithmetic, data interpretation, and logical problem-solving.
- **Abstract Reasoning**: Evaluates the ability to identify patterns, logical rules, and trends in new data.
- **Mechanical Reasoning**: Measures understanding of mechanical and physical principles.
- **Spatial Reasoning**: Assesses the ability to visualize and manipulate objects.
3. **Format**: Aptitude tests can be multiple-choice, true/false, or involve practical problem-solving tasks. They are often timed, with specific sections dedicated to each type of reasoning.
4. **Preparation**:
- **Practice Tests**: Taking practice tests helps familiarize with the format and types of questions.
- **Study Guides**: Reviewing basic concepts in mathematics, grammar, and logical reasoning.
- **Skills Development**: Enhancing skills through puzzles, reading, and other related activities.
5. **Usage**:
- **Recruitment**: Employers use aptitude tests to screen job applicants and find the best fit for a role.
- **Education**: Schools and colleges use these tests for admissions, placement, and identifying areas for student improvement.
- **Career Counseling**: Helps individuals understand their strengths and areas for improvement, guiding career choices.
6. **Scoring**: Scores are typically presented as percentiles, showing how a test-taker compares to a norm group. Higher scores indicate better performance relative to the norm group.
If you have specific questions about a certain type of aptitude test or need preparation tips, feel free to ask!
I am intrested in sata vikas group
M99 work involves varnishing and using a micrometer to measure the thickness of the varnish layer.
M99 work refers to the process of varnishing surfaces to protect them from damage and corrosion.
Varnior is a tool used in M99 work to apply varnish evenly on surfaces.
A micrometer is used to measure the thickness of the varnish layer applied during M99 work.
Accurate measurement with a micrometer is crucial for ensuring the
Poka yoke is a method for mistake-proofing processes, while 5S is a workplace organization method.
Poka yoke focuses on preventing errors by designing processes that make mistakes impossible or easily detectable.
5S involves organizing the workplace to improve efficiency and safety through the principles of Sort, Set in order, Shine, Standardize, and Sustain.
Examples of poka yoke include using color coding to prevent mix...
I believe in making informed decisions based on my interests, skills, and long-term goals.
Consider my interests and passions
Assess my skills and strengths
Research different career options
Set long-term goals and align career choice with them
I have a strong knowledge of the required profile and am highly motivated to contribute to the team's success.
I have a solid understanding of the skills and qualifications needed for this role.
I am enthusiastic about the opportunity to learn and grow within the company.
I am a quick learner and have a strong work ethic.
I am confident in my ability to contribute positively to the team and achieve results.
I am passionate ...
posted on 23 Oct 2024
I applied via LinkedIn and was interviewed in Sep 2024. There was 1 interview round.
MDP stands for Markov Decision Process, a mathematical framework used for modeling decision-making in situations where outcomes are partly random and partly under the control of a decision maker.
MDP is a mathematical framework used in reinforcement learning to model decision-making processes.
It consists of a set of states, actions, transition probabilities, and rewards.
The goal is to find a policy that maximizes the ex...
To reduce engine out NOx, optimize combustion process, use exhaust gas recirculation, and employ selective catalytic reduction.
Optimize combustion process by adjusting air-fuel ratio and ignition timing
Utilize exhaust gas recirculation to reduce oxygen concentration in combustion chamber
Employ selective catalytic reduction to convert NOx into harmless nitrogen and water
posted on 1 May 2024
I applied via Recruitment Consulltant and was interviewed in Apr 2024. There were 2 interview rounds.
based on 1 interview
Interview experience
based on 5 reviews
Rating in categories
Mechanical Engg. Design
4
salaries
| ₹4.3 L/yr - ₹5.5 L/yr |
Embedded Engineer
3
salaries
| ₹3 L/yr - ₹4 L/yr |
Ather Energy
Ultraviolette Automotive
Tork Motors
Ola Electric Mobility