Upload Button Icon Add office photos

Filter interviews by

Arabian Fal Mechanical Engineer Interview Questions and Answers

Updated 4 Mar 2024

Arabian Fal Mechanical Engineer Interview Experiences

1 interview found

Interview experience
2
Poor
Difficulty level
-
Process Duration
-
Result
-
Round 1 - One-on-one 

(1 Question)

  • Q1. Coating defects

Interview questions from similar companies

I applied via Naukri.com and was interviewed before Jun 2020. There was 1 interview round.

Interview Questionnaire 

28 Questions

  • Q1. What is mean by safety
  • Ans. 

    Safety refers to the condition of being protected from harm, danger, or injury.

    • Safety involves taking measures to prevent accidents and injuries

    • It includes following rules and regulations to ensure a safe environment

    • Safety can be achieved through proper training and education

    • Examples of safety measures include wearing protective gear, using safety equipment, and practicing safe behaviors

    • Safety is important in all indus...

  • Answered by AI
  • Q2. What is LEL
  • Ans. 

    LEL stands for Lower Explosive Limit and is the minimum concentration of a gas or vapor in air that can ignite.

    • LEL is a safety term used in industries dealing with flammable gases and liquids.

    • It is expressed as a percentage of the gas or vapor in air.

    • If the concentration of the gas or vapor is below the LEL, it is too lean to ignite.

    • If the concentration is above the LEL, it is too rich and can ignite.

    • For example, the L...

  • Answered by AI
  • Q3. What is RA
  • Q4. What is JSA/JHA
  • Ans. 

    JSA/JHA stands for Job Safety Analysis/Job Hazard Analysis. It is a process of identifying potential hazards and risks in a job or task.

    • JSA/JHA is a systematic approach to identify and mitigate potential hazards in a job or task

    • It involves breaking down a job or task into steps and analyzing each step for potential hazards

    • The analysis includes identifying the hazards, assessing the risks, and implementing controls to m...

  • Answered by AI
  • Q5. Role of HSE
  • Ans. 

    HSE plays a crucial role in ensuring the safety and well-being of employees and the environment.

    • HSE stands for Health, Safety, and Environment.

    • It involves identifying and assessing potential hazards and implementing measures to control or eliminate them.

    • HSE also includes training employees on safety procedures and emergency response plans.

    • Examples of HSE measures include wearing personal protective equipment, conductin...

  • Answered by AI
  • Q6. What is Hchem
  • Ans. 

    Hchem is not a known term or acronym in the engineering field.

    • Hchem is not a commonly used term in engineering

    • It is possible that the interviewer misspoke or meant to ask a different question

    • Without more context, it is difficult to provide a more specific answer

  • Answered by AI
  • Q7. What is Hazop
  • Ans. 

    Hazop is a structured and systematic technique used to identify potential hazards and operability problems in industrial processes.

    • Hazop stands for Hazard and Operability Study

    • It involves a team of experts analyzing a process to identify potential hazards and operability issues

    • Hazop is commonly used in the chemical, oil and gas, and pharmaceutical industries

    • The process involves breaking down the process into smaller pa...

  • Answered by AI
  • Q8. What is confined space
  • Ans. 

    Confined space refers to an area that is enclosed and has limited access and ventilation.

    • Examples include tanks, silos, sewers, and tunnels.

    • Workers entering confined spaces must follow safety protocols and use specialized equipment.

    • Hazards in confined spaces include lack of oxygen, toxic gases, and physical obstructions.

    • Proper training and communication are crucial for working in confined spaces.

  • Answered by AI
  • Q9. What is work at height
  • Ans. 

    Work at height refers to any task performed at a height where a person could fall and injure themselves.

    • Work at height involves working on ladders, scaffolding, roofs, or any other elevated surface

    • It is important to use appropriate safety equipment such as harnesses, guardrails, and safety nets

    • Workers should be trained on how to safely work at height and how to properly use safety equipment

    • Examples of work at height in...

  • Answered by AI
  • Q10. Hazard of confined space
  • Ans. 

    Confined spaces pose a significant hazard due to limited entry and exit points, poor ventilation, and potential for hazardous substances.

    • Limited entry and exit points can make it difficult to escape in case of an emergency

    • Poor ventilation can lead to a buildup of toxic gases or lack of oxygen

    • Potential for hazardous substances such as chemicals, fumes, or dust

    • Examples include tanks, silos, sewers, and tunnels

    • Proper trai...

  • Answered by AI
  • Q11. Precautions of confined space
  • Ans. 

    Precautions to be taken while working in confined spaces

    • Proper ventilation and air quality testing

    • Use of personal protective equipment

    • Proper lighting and communication equipment

    • Training and certification for workers

    • Emergency rescue plan in place

  • Answered by AI
  • Q12. What is LEL&UEL
  • Ans. 

    LEL&UEL stands for Lower Explosive Limit and Upper Explosive Limit respectively. They are the minimum and maximum concentrations of a flammable gas or vapor in air that can ignite.

    • LEL is the lowest concentration of a gas or vapor that can ignite

    • UEL is the highest concentration of a gas or vapor that can ignite

    • Concentrations between LEL and UEL are considered flammable

    • LEL and UEL vary depending on the gas or vapor

    • LEL an...

  • Answered by AI
  • Q13. What is competent person
  • Q14. What is fire
  • Ans. 

    Fire is a chemical reaction that releases heat, light, and various gases.

    • Fire is a rapid oxidation process that occurs when fuel (such as wood, paper, or gasoline) combines with oxygen in the presence of heat or a spark.

    • It releases heat, light, and various gases such as carbon dioxide, water vapor, and nitrogen oxides.

    • Fire can be beneficial (such as for cooking or heating) or destructive (such as in wildfires or house ...

  • Answered by AI
  • Q15. Types of fire
  • Ans. 

    There are four types of fire: Class A, Class B, Class C, and Class D.

    • Class A fires involve ordinary combustibles such as wood, paper, or cloth.

    • Class B fires involve flammable liquids or gases such as gasoline, oil, or propane.

    • Class C fires involve electrical equipment such as appliances, wiring, or circuit breakers.

    • Class D fires involve combustible metals such as magnesium, titanium, or sodium.

  • Answered by AI
  • Q16. Type of extinguisher
  • Ans. 

    There are different types of fire extinguishers for different types of fires.

    • Water extinguishers for Class A fires (wood, paper, cloth, etc.)

    • CO2 extinguishers for Class B and C fires (flammable liquids and electrical fires)

    • Dry chemical extinguishers for Class A, B, and C fires

    • Foam extinguishers for Class A and B fires

    • Wet chemical extinguishers for Class K fires (cooking oils and fats)

  • Answered by AI
  • Q17. Modes of heat transfer
  • Ans. 

    Modes of heat transfer include conduction, convection, and radiation.

    • Conduction is the transfer of heat through a material without any movement of the material itself.

    • Convection is the transfer of heat through the movement of fluids, such as air or water.

    • Radiation is the transfer of heat through electromagnetic waves, such as from the sun or a fire.

  • Answered by AI
  • Q18. How to prevent fire
  • Ans. 

    Preventing fire requires proper handling of flammable materials and regular maintenance of electrical equipment.

    • Store flammable materials in designated areas away from heat sources

    • Regularly inspect and maintain electrical equipment

    • Install smoke detectors and fire extinguishers in appropriate locations

    • Train employees on fire safety procedures and evacuation plans

  • Answered by AI
  • Q19. What is msds
  • Ans. 

    MSDS stands for Material Safety Data Sheet.

    • MSDS provides information about hazardous chemicals and substances.

    • It includes information about the physical and chemical properties of the substance, health hazards, precautions for safe handling and use, and emergency procedures.

    • MSDS is required by law for all hazardous chemicals and substances used in the workplace.

    • It is important to read and understand the MSDS before usi...

  • Answered by AI
  • Q20. How to do firefighting
  • Ans. 

    Firefighting involves identifying and extinguishing fires to prevent damage and loss of life.

    • Assess the situation and determine the type and size of fire

    • Use appropriate firefighting equipment such as fire extinguishers, hoses, and pumps

    • Follow safety protocols and wear protective gear

    • Coordinate with other firefighters and emergency responders

    • Evacuate people from the affected area

    • Monitor the situation and ensure the fire

  • Answered by AI
  • Q21. How to prevent the accident
  • Ans. 

    Prevent accidents by identifying potential hazards and implementing safety measures.

    • Conduct regular safety audits and risk assessments

    • Provide proper training and education to employees

    • Implement safety protocols and procedures

    • Use appropriate safety equipment and gear

    • Encourage a culture of safety and accountability

    • Regularly review and update safety policies and procedures

  • Answered by AI
  • Q22. How to investigate the accident
  • Ans. 

    To investigate an accident, follow a systematic approach involving data collection, analysis, and identification of root causes.

    • Gather all available information about the accident, including eyewitness accounts, photographs, and any relevant documents or records.

    • Conduct interviews with individuals involved in the accident to gather their perspectives and insights.

    • Examine the accident scene for physical evidence, such a...

  • Answered by AI
  • Q23. Emergency procedure
  • Q24. What is H2s
  • Ans. 

    H2S is a colorless, flammable, and toxic gas with a strong odor of rotten eggs.

    • H2S is commonly known as hydrogen sulfide.

    • It is produced naturally by the breakdown of organic matter and is found in natural gas, crude oil, and volcanic gases.

    • It is highly toxic and can cause respiratory failure, loss of consciousness, and even death.

    • H2S is used in various industries such as oil and gas, mining, and pulp and paper.

    • It is al...

  • Answered by AI
  • Q25. Properties of H2s
  • Ans. 

    H2S is a colorless, flammable, and toxic gas with a strong odor of rotten eggs.

    • H2S is highly flammable and can ignite easily

    • It is toxic and can cause respiratory failure

    • It has a distinctive odor of rotten eggs

    • H2S is used in the production of sulfuric acid and in the petroleum industry

  • Answered by AI
  • Q26. Hirerchy procedure
  • Q27. Permissible exposure limit of H2s,co,co2,methane
  • Ans. 

    Permissible exposure limits (PEL) are the maximum allowable concentrations of hazardous substances in the workplace.

    • H2S: PEL is 10 ppm (parts per million) over an 8-hour workday

    • CO: PEL is 50 ppm over an 8-hour workday

    • CO2: No specific PEL, but recommended exposure limit is 5,000 ppm over an 8-hour workday

    • Methane: No specific PEL, but recommended exposure limit is 1,000 ppm over an 8-hour workday

  • Answered by AI
  • Q28. Short term exposure limit of H2s
  • Ans. 

    Short term exposure limit (STEL) of H2S is 10 ppm.

    • STEL is the maximum concentration of a substance that a worker can be exposed to for a short period of time without suffering from immediate or long-term health effects.

    • The STEL for H2S is set at 10 ppm (parts per million) by OSHA (Occupational Safety and Health Administration).

    • Exposure to H2S at levels above the STEL can cause symptoms such as eye irritation, headache,...

  • Answered by AI

Interview Preparation Tips

Interview preparation tips for other job seekers - Keep calm when you are giving the interview and first prepare the interview

I applied via Recruitment Consulltant and was interviewed before Jun 2021. There were 6 interview rounds.

Round 1 - Resume Shortlist 
Pro Tip by AmbitionBox:
Keep your resume crisp and to the point. A recruiter looks at your resume for an average of 6 seconds, make sure to leave the best impression.
View all tips
Round 2 - One-on-one 

(6 Questions)

  • Q1. Explain your self and where did you working current in 2014
  • Q2. Which gas can use for while hot/live tapping
  • Ans. 

    Nitrogen gas is commonly used for hot/live tapping in mechanical engineering.

    • Nitrogen gas is inert and non-reactive, making it safe to use in hot/live tapping processes.

    • It helps to create a protective atmosphere to prevent explosions or fires.

    • Nitrogen gas is readily available and cost-effective.

    • Other gases like argon or carbon dioxide can also be used depending on the specific requirements.

  • Answered by AI
  • Q3. Which method can we follow for railway/road/river crossings
  • Ans. 

    Various methods can be used for railway/road/river crossings depending on the location and other factors.

    • Bridges can be built over the crossing

    • Tunnels can be dug under the crossing

    • Level crossings can be used for roads

    • Flyovers can be constructed for roads

    • Ferries can be used for river crossings

    • Aqueducts can be built for waterways

    • Location, traffic volume, and safety considerations must be taken into account when choosing

  • Answered by AI
  • Q4. Which procedure can follow for pipe lines welding while route and filling
  • Ans. 

    The procedure for pipe lines welding while route and filling involves several steps.

    • Clean the area to be welded thoroughly

    • Tack weld the pipes together

    • Weld the root pass

    • Fill the remaining gap with weld metal

    • Perform post-weld heat treatment if required

    • Inspect the weld for defects

  • Answered by AI
  • Q5. Cross country pipeline code - Nitrogen
  • Q6. Explain About RT, UT, and magnetic partials
  • Ans. 

    RT, UT, and magnetic partials are non-destructive testing methods used in engineering.

    • RT stands for Radiographic Testing and uses X-rays or gamma rays to inspect the internal structure of a material.

    • UT stands for Ultrasonic Testing and uses high-frequency sound waves to detect flaws or defects in a material.

    • Magnetic particle testing uses magnetic fields and iron particles to detect surface and slightly subsurface defec...

  • Answered by AI
Round 3 - Assignment 

What IS API 5L

Round 4 - Coding Test 

What is ASME B 16.5

Round 5 - Coding Test 

What is ASME IX

Round 6 - Coding Test 

Whatbis ASME B 31.4

Interview Preparation Tips

Topics to prepare for Saudi Aramco Mechanical Engineer interview:
  • ASME, API, ASTM, ANSI,
Interview preparation tips for other job seekers - Feel free just listion and first what they are asking then don't give chance to them ask any other questions.
Even I attended in Chennai for other company but they call me for as a Project manager interview and they ask me questions in design, fabrication and supply time management. Then it's confirmed that post they already reserved for some others. If they reserve already they should not call for interveiw.

I applied via Naukri.com and was interviewed in Oct 2020. There were 3 interview rounds.

Interview Questionnaire 

1 Question

  • Q1. The HR round was very pathetic. Sreethala took my HR round.

Interview Preparation Tips

Interview preparation tips for other job seekers - Please don't waste your precious time in giving the interview for Baker Hughes, Powai
Mumbai location. They will take all the interview rounds. The HR will ask you to submit all documents and last moment they will cancel your candidature without giving you any specific reason.

I applied via Company Website and was interviewed in Aug 2022. There were 3 interview rounds.

Round 1 - Resume Shortlist 
Pro Tip by AmbitionBox:
Keep your resume crisp and to the point. A recruiter looks at your resume for an average of 6 seconds, make sure to leave the best impression.
View all tips
Round 2 - Technical 

(1 Question)

  • Q1. Basic Question related to mechanical basics
Round 3 - HR 

(2 Questions)

  • Q1. Tell me about yourself
  • Q2. Strength & Weakness, Where you see 5 years from now.

Interview Preparation Tips

Interview preparation tips for other job seekers - Be strong on your basic engineering. Prepare HR round. HR process is very slow. It will take at least 1.5months to release your offer.
Interview experience
5
Excellent
Difficulty level
Easy
Process Duration
4-6 weeks
Result
Selected Selected

I applied via Campus Placement and was interviewed before Sep 2022. There were 3 interview rounds.

Round 1 - Resume Shortlist 
Pro Tip by AmbitionBox:
Don’t add your photo or details such as gender, age, and address in your resume. These details do not add any value.
View all tips
Round 2 - Technical 

(1 Question)

  • Q1. What would you do if the design called for tight tolerances and the part was manufactured out of tolerance
  • Ans. 

    I would assess the impact of the out-of-tolerance part and determine if it can still function within acceptable limits or if it needs to be reworked or replaced.

    • Assess the functionality of the part with the out-of-tolerance dimensions

    • Determine if the part can still meet the overall design requirements despite being out of tolerance

    • Consider the potential impact on the performance and safety of the final product

    • Consult w...

  • Answered by AI
Round 3 - Technical 

(1 Question)

  • Q1. Tell me what you see about his drawing
  • Ans. 

    The drawing appears to be a mechanical component with multiple parts and dimensions.

    • The drawing includes various geometric shapes such as circles, rectangles, and lines.

    • There are labels indicating dimensions and measurements for each part.

    • The drawing may also include annotations or symbols representing different materials or processes.

    • It seems to be a detailed technical drawing for manufacturing or assembly purposes.

  • Answered by AI

Skills evaluated in this interview

Round 1 - Technical 

(3 Questions)

  • Q1. What is yield strength and ultimate strength
  • Ans. 

    Yield strength is the stress at which a material begins to deform plastically, while ultimate strength is the maximum stress a material can withstand before breaking.

    • Yield strength is the point where a material starts to deform plastically, meaning it will not return to its original shape once the stress is removed.

    • Ultimate strength is the maximum stress a material can withstand before it breaks or fractures.

    • Yield stre...

  • Answered by AI
  • Q2. All FEA related questions
  • Q3. All basic SOM and SHEET METAL RELATED QUESTIONS

Interview Preparation Tips

Interview preparation tips for other job seekers - Prepare for fea and matlab even though if your gd shows only creo modelling responsibility.

I applied via Recruitment Consultant and was interviewed in Dec 2020. There were 6 interview rounds.

Interview Questionnaire 

2 Questions

  • Q1. 1st round is technical , 2nd is values & behaviors , 3rd is assessment road
  • Q2. Be clear on values & behaviours , practice assement round offline before attempting

Interview Preparation Tips

Interview preparation tips for other job seekers - its a long process may take 2-3 months , there is internal & external assement before selectioon is finalized . Good luck
Interview experience
4
Good
Difficulty level
Hard
Process Duration
2-4 weeks
Result
Not Selected

I applied via Company Website and was interviewed in May 2024. There were 2 interview rounds.

Round 1 - Group Discussion 

Behavioral questions and resume delve

Round 2 - Case Study 

Pmi - product management information

Interview Preparation Tips

Interview preparation tips for other job seekers - study supply chain, product management information and presentation
Interview experience
5
Excellent
Difficulty level
Moderate
Process Duration
Less than 2 weeks
Result
Selected Selected

I appeared for an interview before Feb 2024.

Round 1 - Interview 

(2 Questions)

  • Q1. Tell me about Pumps
  • Q2. Can you design a pump with its specifications parameters

Arabian Fal Interview FAQs

How many rounds are there in Arabian Fal Mechanical Engineer interview?
Arabian Fal interview process usually has 1 rounds. The most common rounds in the Arabian Fal interview process are One-on-one Round.

Tell us how to improve this page.

Arabian Fal Mechanical Engineer Interview Process

based on 1 interview

Interview experience

2
  
Poor
View more

Interview Questions from Similar Companies

Bharat Petroleum Interview Questions
4.1
 • 149 Interviews
Schlumberger Interview Questions
3.9
 • 140 Interviews
ExxonMobil Interview Questions
3.8
 • 65 Interviews
bp Interview Questions
3.8
 • 61 Interviews
Saudi Aramco Interview Questions
4.4
 • 56 Interviews
Baker Hughes Interview Questions
4.0
 • 55 Interviews
Petrofac Interview Questions
4.3
 • 41 Interviews
Cairn Energy Interview Questions
3.7
 • 30 Interviews
View all
Arabian Fal Mechanical Engineer Salary
based on 17 salaries
₹4.8 L/yr - ₹8.5 L/yr
56% more than the average Mechanical Engineer Salary in India
View more details

Arabian Fal Mechanical Engineer Reviews and Ratings

based on 14 reviews

2.6/5

Rating in categories

2.7

Skill development

2.7

Work-life balance

2.7

Salary

2.7

Job security

2.2

Company culture

2.4

Promotions

2.4

Work satisfaction

Explore 14 Reviews and Ratings
Mechanical Engineer
17 salaries
unlock blur

₹4.8 L/yr - ₹8.5 L/yr

Planning Engineer
10 salaries
unlock blur

₹7 L/yr - ₹12 L/yr

Safety Officer
9 salaries
unlock blur

₹5 L/yr - ₹11 L/yr

Mechanical Supervisor
6 salaries
unlock blur

₹4.7 L/yr - ₹8 L/yr

Instrument Engineer
6 salaries
unlock blur

₹0.9 L/yr - ₹9 L/yr

Explore more salaries
Compare Arabian Fal with

Bharat Petroleum

4.1
Compare

Hindustan Petroleum

4.2
Compare

Petrofac

4.3
Compare

Schlumberger

3.9
Compare
Did you find this page helpful?
Yes No
write
Share an Interview