20+ Environmental Health and Safety Lead Interview Questions and Answers

Fire NOC conditions are the set of requirements that a building or establishment must meet to obtain a No Objection Certificate for fire safety.

• Fire NOC conditions include having adequate fire exits, fire alarms, fire extinguishers, and sprinkler systems.

• The building must also have clear access for fire trucks and emergency personnel.

• Regular fire drills and safety training for employees are also required.

• Examples of Fire NOC conditions can vary depending on the local fire saf...read more

Fire extinguisher requirements vary based on the hazard level of the workplace.

• Light hazard workplaces require water, foam, or dry powder extinguishers.

• Ordinary hazard workplaces require water, foam, dry powder, or carbon dioxide extinguishers.

• High hazard workplaces require foam, dry powder, carbon dioxide, or specialized extinguishers such as halon or clean agent.

• The specific requirements may vary by country and industry.

• It is important to regularly inspect and maintain fire...read more

After LOTO or isolation of electrical energy, a mechanism must be used to check whether electrical energy isolation has been done or not.

• Visual inspection of the equipment to ensure that it is not energized

• Use of a voltage tester to check for the presence of electrical energy

• Verification of the LOTO or isolation tag

• Testing the equipment to ensure that it is not operational

• Communication with other workers to ensure that they are aware of the isolation

• Documentation of the isola...read more

Height work equipment includes ladders, scaffolds, aerial lifts, and fall protection systems.

• Ladders: used for low height work

• Scaffolds: used for medium height work

• Aerial lifts: used for high height work

• Fall protection systems: used to prevent falls from height

• Examples: extension ladders, rolling scaffolds, scissor lifts, harnesses, guardrails

Fire extinguishers should be placed at a height of 3.5 to 5 feet from the floor.

• The ideal height for fire extinguishers is between 3.5 to 5 feet from the floor.

• This ensures that the extinguisher is easily accessible in case of a fire.

• The height should be adjusted based on the height of the ceiling and the size of the room.

• Extinguishers should be mounted on brackets or in cabinets to prevent them from falling.

• It is important to ensure that the extinguisher is visible and not o...read more

Legal compliance for mechanical materials lifting equipment include OSHA regulations, ANSI standards, and manufacturer guidelines.

• OSHA regulations require regular inspections and maintenance of lifting equipment.

• ANSI standards provide guidelines for the design, construction, and testing of lifting equipment.

• Manufacturer guidelines must be followed for proper use and maintenance of specific equipment.

• Compliance with these regulations and standards helps ensure the safety of wo...read more

Construction hazards include falls, electrical hazards, noise, and exposure to hazardous materials.

• Falls from heights or on slippery surfaces

• Electrical hazards from exposed wires or faulty equipment

• Noise exposure from heavy machinery and equipment

• Exposure to hazardous materials such as asbestos, lead, and silica dust

• Risk of fires and explosions from flammable materials and chemicals

• Physical strain and injuries from lifting heavy objects and repetitive motions

Fire NOC & CTO compliance is done by the local fire department and pollution control board respectively.

• Fire NOC compliance is done by the local fire department.

• CTO compliance is done by the pollution control board.

• Both compliances are mandatory for any organization to operate.

• The process involves inspection of the premises and ensuring all safety measures are in place.

• Non-compliance can result in penalties and even closure of the organization.

Various material lifting equipment are used in warehouses depending on the type of material and its weight.

• Forklifts are commonly used for heavy loads

• Pallet jacks are used for moving pallets

• Hand trucks are used for smaller loads

• Conveyor belts are used for continuous movement of materials

• Hoists and cranes are used for lifting heavy equipment

• Scissor lifts are used for lifting workers to higher levels

• Loading dock levelers are used for loading and unloading trucks

• Rolling ladders ...read more

The fire water tank capacity is 50,000 gallons.

• The fire water tank is used for emergency firefighting purposes.

• It is important to regularly check and maintain the tank to ensure it is always ready for use.

• The capacity of the tank may vary depending on the size and needs of the facility.

• For example, a smaller facility may have a fire water tank with a capacity of 10,000 gallons.

• On the other hand, a larger facility may have a tank with a capacity of 100,000 gallons or more.

Load lifting capacity decreases as radius increases.

• The load lifting capacity is inversely proportional to the radius.

• As the radius increases, the load lifting capacity decreases.

• This is because the load moment arm increases with radius, making it harder to lift the load.

• For example, a crane with a longer boom has a lower load lifting capacity than a crane with a shorter boom.

I have extensive knowledge of legal compliance in environmental health and safety.

• I am well-versed in federal, state, and local regulations pertaining to environmental health and safety.

• I have experience interpreting and implementing regulations such as OSHA, EPA, and DOT.

• I have conducted audits and inspections to ensure compliance with applicable laws and regulations.

• I have developed and implemented policies and procedures to maintain legal compliance.

• I have provided trainin...read more

Load center is the point where the weight of the load is concentrated during lifting operation.

• It is the point where the weight of the load is concentrated

• It is important to know the load center to ensure safe lifting operation

• The load center varies depending on the shape and size of the load

• Incorrect load center calculation can lead to accidents and injuries

Electrical maintenance work safety precautions include proper training, use of personal protective equipment, and following lockout/tagout procedures.

• Ensure all electrical equipment is de-energized before maintenance work begins

• Use appropriate personal protective equipment such as gloves, safety glasses, and insulated tools

• Follow lockout/tagout procedures to prevent accidental energization of equipment

• Provide proper training to employees on electrical safety and maintenance p...read more

The type of fire pump depends on the specific needs of the facility and the hazards present.

• Factors to consider when selecting a fire pump include the size of the facility, the type of hazards present, and the water supply available.

• Common types of fire pumps include electric motor-driven pumps, diesel engine-driven pumps, and steam turbine-driven pumps.

• The fire pump should be designed to meet the specific requirements of the facility and comply with relevant codes and standa...read more

Meggar process is a method used to measure the insulation resistance of electrical equipment.

• Meggar process involves applying a high voltage DC current to the equipment and measuring the resulting insulation resistance.

• It is commonly used in the maintenance and testing of electrical equipment to ensure safety and reliability.

• The results of the meggar process can indicate if there are any faults or defects in the insulation of the equipment.

• For example, if the insulation resis...read more

Setting objectives in EHS involves identifying key areas for improvement and creating measurable goals to enhance safety and sustainability at the site.

• Identify key areas for improvement such as waste management, air quality, and employee training

• Create measurable goals for each area, such as reducing waste by 20%, improving air quality by implementing new filtration systems, and increasing employee safety training by 50%

• Establish timelines for achieving these objectives and ...read more

Legal requirements for EHS compliance include regulations set by government agencies to ensure workplace safety and environmental protection.

• Compliance with Occupational Safety and Health Administration (OSHA) regulations

• Adherence to Environmental Protection Agency (EPA) guidelines

• Regular audits and inspections to ensure compliance

• Training programs for employees on safety protocols

• Proper record-keeping of incidents and safety measures taken

• Penalties for non-compliance can inc...read more

Leading parameters are proactive measures while lagging parameters are reactive measures.

• Leading parameters are used to predict and prevent incidents before they occur.

• Lagging parameters are used to measure the impact of an incident after it has occurred.

• Leading parameters are often qualitative in nature, while lagging parameters are quantitative.

• Examples of leading parameters include safety training, hazard identification, and risk assessments.

• Examples of lagging parameters ...read more