i
Tejas Networks
Filter interviews by
I applied via Recruitment Consulltant and was interviewed in Dec 2024. There were 2 interview rounds.
STM-1 link refers to a Synchronous Transport Module level 1 link used in telecommunications for transmitting data.
STM-1 link operates at a data rate of 155.52 Mbps.
It is commonly used in SDH (Synchronous Digital Hierarchy) networks.
STM-1 link can carry multiple DS3 or E3 circuits.
It is equivalent to 63 E1 channels or 28 DS1 channels.
An IP address is a unique numerical label assigned to each device connected to a computer network, while a subnet mask is used to divide an IP network into subnetworks.
IP address identifies a device on a network, like 192.168.1.1
Subnet mask determines the network portion of an IP address, like 255.255.255.0
Subnet mask is used to separate the network and host portions of an IP address
OSI and TCP/IP models are networking models that define how data is transmitted over a network.
OSI model has 7 layers: Physical, Data Link, Network, Transport, Session, Presentation, Application.
TCP/IP model has 4 layers: Network Interface, Internet, Transport, Application.
OSI model is theoretical while TCP/IP model is practical and widely used.
OSI model is a reference model while TCP/IP model is a protocol stack.
Examp...
Requirements and capacity of stm-1 link implementation
Requirements include fiber optic cables, SDH equipment, and proper configuration
Capacity of stm-1 link is 155.52 Mbps
STM-1 link is commonly used in telecommunications for high-speed data transmission
An IP address is a unique numerical label assigned to each device connected to a computer network. IPv4 uses 32-bit addresses, while IPv6 uses 128-bit addresses.
IP address is a unique identifier for devices on a network.
IPv4 uses 32-bit addresses, represented in decimal format (e.g. 192.168.1.1).
IPv6 uses 128-bit addresses, represented in hexadecimal format (e.g. 2001:0db8:85a3:0000:0000:8a2e:0370:7334).
VLAN stands for Virtual Local Area Network. VLAN ID is a unique identifier assigned to a VLAN.
VLAN is a logical grouping of devices on the same network segment.
VLANs help in segmenting network traffic for security and performance reasons.
VLAN ID is a number assigned to each VLAN to differentiate it from others.
For example, VLAN 10 might be used for finance department while VLAN 20 for marketing.
Layer-2 and layer-3 services refer to different levels of network services in the OSI model.
Layer-2 services operate at the data link layer and include functions like MAC address assignment and Ethernet switching.
Layer-3 services operate at the network layer and include functions like IP address assignment and routing.
The main difference between layer-2 and layer-3 services is the level at which they operate in the OSI...
SDH structure refers to the hierarchy of synchronous digital signals, while SDH frame is the basic unit of data transmission in SDH networks.
SDH structure includes various levels such as STM-1, STM-4, STM-16, etc.
SDH frame consists of a fixed number of bytes, with overhead for management and error correction.
SDH frame structure includes sections, lines, and paths for data transmission.
Example: STM-1 is a common level i...
DCCR stands for Data Center Control Room and DCCM stands for Data Center Construction Manager.
DCCR is a centralized location within a data center where operators monitor the performance of servers, networks, and other equipment.
DCCM is responsible for overseeing the construction and maintenance of data center facilities.
Examples: DCCR helps in ensuring smooth operations of data centers by monitoring and managing resour...
IPv4 address of Google DNS server is 8.8.8.8 and IPv6 address is 2001:4860:4860::8888.
IPv4 address: 8.8.8.8
IPv6 address: 2001:4860:4860::8888
Subnet mask is used to divide an IP network into subnetworks, determining the network and host portions of an IP address.
Subnet mask is a 32-bit number that separates the network and host portions of an IP address.
To calculate the number of usable IPs in a subnet, subtract 2 from the total number of IPs in the subnet.
Network host IP is the first IP address in a subnet, while broadcast IP is the last IP address in a sub...
Different kinds of cards used in Tejas 1400 and 1600 mux include line cards, switch cards, and power cards.
Line cards: used for connecting the mux to external devices
Switch cards: used for routing data within the mux
Power cards: used for providing power to the mux
Examples: STM-1 line card, STM-4 switch card, power supply card
The main difference between xa60g and xa20g cards is the processing power and memory capacity.
xa60g card has higher processing power and memory capacity compared to xa20g card
xa60g card is more suitable for high-performance computing tasks
xa20g card may be more cost-effective for less demanding applications
GPON technology is a type of passive optical network that uses fiber-optic cables to deliver high-speed internet, TV, and phone services.
GPON stands for Gigabit Passive Optical Network
It uses a point-to-multipoint architecture, where a single optical fiber serves multiple users
GPON architecture includes an Optical Line Terminal (OLT) at the service provider's central office and Optical Network Terminals (ONTs) at the c...
Nodes can be added and deleted in NMS by using the management interface or command line interface.
Nodes can be added through the management interface by selecting the 'Add Node' option and providing the necessary information such as IP address, hostname, and SNMP credentials.
Nodes can also be added through the command line interface by using specific commands to add a new node to the network management system.
To delete...
To upgrade software in OLT, ONT, and Tejas 1400 locally and from NMS, follow these steps.
Locally: Use a USB drive to transfer the software update file to the device. Access the device's management interface and initiate the upgrade process.
From NMS: Use the Network Management System (NMS) to remotely push the software update to the devices. Schedule the upgrade during off-peak hours to minimize disruption.
Ensure compat...
Different types of alarms in Tejas equipments include power alarms, temperature alarms, and communication alarms.
Power alarms: indicate issues with power supply or voltage levels
Temperature alarms: alert when equipment temperature exceeds safe limits
Communication alarms: signal problems with data transmission or network connectivity
VCG stands for Voltage Controlled Gain and VCAT stands for Voltage Controlled Attenuator.
VCG is a circuit that adjusts the gain of an amplifier based on a control voltage.
VCAT is a circuit that adjusts the attenuation of a signal based on a control voltage.
Both VCG and VCAT are commonly used in electronic devices to control signal levels.
Example: VCG can be used in audio amplifiers to adjust the volume based on user in...
MPLS stands for Multiprotocol Label Switching. It is a protocol used in high-performance telecommunications networks.
Advantages of MPLS include improved performance, scalability, quality of service, and traffic engineering capabilities
MPLS allows for efficient packet forwarding based on labels instead of IP addresses
MPLS can support different types of traffic, such as voice, video, and data, with different service leve...
Top trending discussions
I applied via Naukri.com and was interviewed before Oct 2021. There were 3 interview rounds.
AD DNS DHCP are Microsoft technologies used for network management and authentication.
Active Directory (AD) is a directory service used for authentication and authorization of users and computers in a network.
Domain Name System (DNS) is used for name resolution of network resources.
Dynamic Host Configuration Protocol (DHCP) is used for automatic IP address assignment to network devices.
AD, DNS, and DHCP are often used ...
IaaS, SaaS, and PaaS are cloud computing models that provide different levels of infrastructure, software, and platform services.
IaaS (Infrastructure as a Service) provides virtualized computing resources over the internet, such as servers, storage, and networking.
SaaS (Software as a Service) delivers software applications over the internet, eliminating the need for local installation and maintenance.
PaaS (Platform as ...
General questions for 1 hors online exams
I applied via Recruitment Consultant
I will drive innovation through cross-functional collaboration, continuous learning, and data-driven decision-making.
Promote cross-functional collaboration to leverage diverse perspectives and expertise
Encourage continuous learning and development to stay ahead of industry trends
Utilize data-driven decision-making to identify opportunities for growth and optimization
I applied via LinkedIn and was interviewed before Oct 2021. There were 2 interview rounds.
I applied via Naukri.com and was interviewed before Jan 2022. There were 3 interview rounds.
I applied via Company Website and was interviewed in Oct 2022. There were 2 interview rounds.
I was previously working as a Software Engineer at XYZ Company.
Developed and maintained software applications
Collaborated with cross-functional teams to gather requirements and design solutions
Implemented new features and enhancements
Performed code reviews and debugging
Participated in agile development processes
I am familiar with a wide range of test equipment including oscilloscopes, multimeters, signal generators, and power supplies.
Oscilloscopes: Tektronix TDS2024B, Agilent DSO-X 2002A
Multimeters: Fluke 87V, Keysight U1253B
Signal generators: Tektronix AFG3102, Agilent 33220A
Power supplies: Agilent E3631A, Tektronix PS2520G
I have a systematic approach to fault rectification, starting with identifying the root cause and then implementing a solution.
I begin by gathering information about the problem and analyzing it thoroughly
I then identify the root cause of the issue and prioritize the most critical problems
I develop a plan of action and implement a solution, testing it thoroughly to ensure it is effective
I document the entire process fo...
Our system operates on the 2.4 GHz frequency band.
Our system uses the 2.4 GHz frequency band for communication.
This frequency band is commonly used for Wi-Fi and Bluetooth devices.
It has a range of approximately 30 meters indoors.
The 2.4 GHz band is susceptible to interference from other devices operating on the same frequency.
Our system has been optimized to minimize interference and ensure reliable communication.
Yes, I am ready to travel frequently to different locations within India.
I have a flexible schedule and am willing to travel as required.
I have previous experience traveling for work.
I understand the importance of being adaptable and open to new locations.
I am familiar with the travel logistics within India.
I am excited about the opportunity to explore different parts of the country.
I applied via Newspaper Ad and was interviewed before Mar 2022. There were 2 interview rounds.
Normal aptitude questions were asked.
I applied via Naukri.com and was interviewed in May 2022. There were 3 interview rounds.
Some of the top questions asked at the Tejas Networks Engineer interview -
based on 1 interview
Interview experience
based on 16 reviews
Rating in categories
R&D Engineer
268
salaries
| ₹0 L/yr - ₹0 L/yr |
Network Engineer
161
salaries
| ₹0 L/yr - ₹0 L/yr |
Senior Engineer
154
salaries
| ₹0 L/yr - ₹0 L/yr |
Engineer
121
salaries
| ₹0 L/yr - ₹0 L/yr |
Software Engineer
92
salaries
| ₹0 L/yr - ₹0 L/yr |
Sterlite Technologies
HFCL Limited
Vihaan Networks
Bharti Airtel