Upload Button Icon Add office photos

Filter interviews by

Swaraj Engines Electrical Maintenance Engineer Interview Questions and Answers

Updated 21 Jul 2022

Swaraj Engines Electrical Maintenance Engineer Interview Experiences

1 interview found

I applied via Approached by Company and was interviewed in Jan 2022. There was 1 interview round.

Round 1 - Technical 

(3 Questions)

  • Q1. Motor winding fault check
  • Ans. Use for multimeter& resistance mode check winding
  • Answered by Deepak Kumar
  • Q2. How to do Earthing Test?
  • Ans. 

    Earthing test is done to ensure proper grounding of electrical equipment and to prevent electrical hazards.

    • Disconnect the equipment from the power source

    • Connect the earth tester to the equipment's earthing point

    • Measure the resistance between the earthing point and the ground

    • Ensure the resistance is within the acceptable range

    • Repeat the test periodically to ensure continued safety

  • Answered by AI
  • Q3. Use for Megger to resistance check
  • Ans. 

    Megger is used to measure insulation resistance in electrical systems.

    • Megger is a type of insulation tester used to measure the resistance of insulation in electrical systems.

    • It is used to detect any insulation breakdown or leakage in the system.

    • The Megger applies a high voltage to the insulation and measures the resulting current flow.

    • The resistance value is then displayed on the Megger's screen.

    • Megger testing is impo...

  • Answered by AI

Interview Preparation Tips

Topics to prepare for Swaraj Engines Electrical Maintenance Engineer interview:
  • Wait lifting hoist
Interview preparation tips for other job seekers - Permanent job & department maintenance area punjab, Himachal

Interview questions from similar companies

I applied via Recruitment Consultant and was interviewed in Jan 2018. There were 6 interview rounds.

Interview Questionnaire 

2 Questions

  • Q1. Introduce my self project explanation technical knowledge about vehicle engine
  • Q2. Diagram understanding knowledge about special machines

Interview Preparation Tips

Round: Resume Shortlist
Experience: B.E Mechanical engineering fresher

Round: Test
Experience: Test about technical knowledge of vehicle

General Tips: Bolt talk with knowledge
ready to adopt any situation
Skills: Body Language, Presentation Skills, Time Management, Decision Making Skills
Duration: <1 week

I applied via Company Website and was interviewed before Jun 2019. There was 1 interview round.

Interview Questionnaire 

1 Question

  • Q1. Can i join mahindra company ?

Interview Preparation Tips

Interview preparation tips for other job seekers - This interview was a technical one but was majorly a stress test. It lasted for about 1 hour 10 minutes. The interviewer wanted to test both my knowledge and communication skills. Most of the questions asked to me were related to my B.Tech curriculum i.e. mechanical engineering related topics. He stressed a lot on the basics related to my project topic. Luckily I was able to answer most of the questions correctly. I tried to answer each question with examples and also used props on the table (like pens, paperweights, pen stands etc.) to explain my theories. It was my first offcampus interview, and I think I did pretty well for a fresher. You need to stay calm and should apply presence of mind. Please go through the job description thoroughly word-by-word and recheck your resume to ensure that you are a best-fit for the position.

I applied via Naukri.com and was interviewed in Nov 2021. There were 2 interview rounds.

Round 1 - Resume Shortlist 
Pro Tip by AmbitionBox:
Keep your resume crisp and to the point. A recruiter looks at your resume for an average of 6 seconds, make sure to leave the best impression.
View all tips
Round 2 - Technical 

(3 Questions)

  • Q1. 7 QC tools, PFMEA, SPC Study
  • Q2. Quality process, MSA Study
  • Q3. Process and product Audit

Interview Preparation Tips

Interview preparation tips for other job seekers - Good interview and good knowledge about QA documents
Interview experience
4
Good
Difficulty level
Moderate
Process Duration
Less than 2 weeks
Result
Selected Selected

I was interviewed in Aug 2024.

Round 1 - Technical 

(3 Questions)

  • Q1. What is the 7QC tools?
  • Ans. 

    The 7QC tools are a set of quality control tools used for process improvement and problem-solving in manufacturing and other industries.

    • Check sheets: Used to collect and organize data for analysis.

    • Cause-and-effect diagrams (Fishbone diagrams): Used to identify and analyze potential causes of a problem.

    • Control charts: Used to monitor process variation over time.

    • Histograms: Used to show the frequency distribution of a se...

  • Answered by AI
  • Q2. What is the 8D methodology?
  • Ans. 

    The 8D methodology is a problem-solving approach used to identify, correct, and prevent recurring problems.

    • 8D stands for 8 disciplines, each representing a step in the problem-solving process

    • It involves creating a team, defining the problem, implementing short-term containment actions, identifying root causes, implementing permanent corrective actions, and preventing recurrence

    • Examples of tools used in 8D methodology i...

  • Answered by AI
  • Q3. What is the 8QB ? Typs
  • Ans. 

    8D is a problem-solving methodology used in quality management to identify, correct, and prevent recurring problems.

    • 8D stands for Eight Disciplines

    • It is a structured problem-solving process typically used in the automotive industry

    • Each discipline represents a step in the process, from defining the problem to implementing long-term solutions

  • Answered by AI
Round 2 - HR 

(2 Questions)

  • Q1. What about family?
  • Q2. Self intro
Round 3 - Aptitude Test 

Any improvement in your industry

Round 4 - Aptitude Test 

Did you profit for any Quality process

I applied via Walk-in and was interviewed in Jun 2021. There was 1 interview round.

Interview Questionnaire 

5 Questions

  • Q1. What is the firing order of 4 cylinder engine?
  • Ans. 

    The firing order of a 4 cylinder engine is 1-3-4-2.

    • Firing order refers to the sequence in which each cylinder fires during the engine's cycle.

    • The firing order is determined by the engine's design and can vary between different types of engines.

    • In a 4 cylinder engine, the firing order is usually 1-3-4-2.

    • This means that the first cylinder to fire is the one closest to the front of the engine, followed by the third cylind

  • Answered by AI
  • Q2. What is the function of connecting rod.?
  • Ans. 

    The connecting rod is a crucial component in an engine that connects the piston to the crankshaft.

    • Transfers the linear motion of the piston to the rotational motion of the crankshaft

    • Converts reciprocating motion into rotational motion

    • Provides a link between the piston and the crankshaft

    • Helps in transmitting power from the piston to the crankshaft

    • Acts as a lever to amplify the force exerted by the piston

    • Plays a role in ...

  • Answered by AI
  • Q3. Types of piston ring.?
  • Ans. 

    Piston rings are of three types: compression rings, oil control rings, and wiper rings.

    • Compression rings seal the combustion chamber and transfer heat from the piston to the cylinder wall.

    • Oil control rings regulate the amount of oil on the cylinder wall and prevent oil from entering the combustion chamber.

    • Wiper rings scrape excess oil from the cylinder wall and prevent it from entering the combustion chamber.

    • Materials ...

  • Answered by AI
  • Q4. What is the full form of FIP.?
  • Ans. 

    FIP stands for Fixed Index Annuity.

    • FIP is a type of annuity that offers a guaranteed minimum interest rate.

    • The interest rate is linked to a stock market index, such as the S&P 500.

    • The interest rate is fixed for a certain period of time, usually several years.

    • FIPs are often used as a retirement savings vehicle.

    • They offer the potential for higher returns than traditional fixed annuities, but with less risk than investing

  • Answered by AI
  • Q5. 0.1 is equal to how many microns?
  • Ans. 

    0.1 microns is equal to 100 nanometers.

    • 1 micron is equal to 1000 nanometers.

    • Therefore, 0.1 micron is equal to 100 nanometers.

    • Microns and nanometers are units of length used to measure very small distances.

    • This conversion is commonly used in fields like nanotechnology and microscopy.

  • Answered by AI

Interview Preparation Tips

Interview preparation tips for other job seekers - This interview was a technical one but was majorly a stress test. It lasted for about 30 minutes. The interviewer wanted to test both my knowledge and communication skills. Most of the questions asked to me were related to my previous experience in like instruments And Guages name. Where it is use Etc.. Basic knowledge of computer related questions.. After that He stresses a lot on the basics related to Engine assembly and Engine components name . Luckily I was able to answer most of the questions correctly.
Interview experience
4
Good
Difficulty level
Moderate
Process Duration
Less than 2 weeks
Result
Selected Selected

I was interviewed in Sep 2022.

Round 1 - Resume Shortlist 
Pro Tip by AmbitionBox:
Keep your resume crisp and to the point. A recruiter looks at your resume for an average of 6 seconds, make sure to leave the best impression.
View all tips
Round 2 - Technical 

(2 Questions)

  • Q1. About your education & work profile in last organization.
  • Q2. About your job & work culture in last organization.

Interview Preparation Tips

Interview preparation tips for other job seekers - Try to focus on Technical questions as well as the last work experience is relavent as per the required profile.

I applied via Walk-in and was interviewed in May 2022. There was 1 interview round.

Round 1 - HR 

(1 Question)

  • Q1. Asking About your salary and discuss

Interview Preparation Tips

Interview preparation tips for other job seekers - Worst of all they will call you for interview but will recruit candidate with their reference so it is useless to go.

I applied via Campus Placement and was interviewed before May 2021. There was 1 interview round.

Round 1 - Technical 

(6 Questions)

  • Q1. What is GD&T And Why used in quality?
  • Ans. 

    GD&T stands for Geometric Dimensioning and Tolerancing. It is used to define and communicate engineering tolerances.

    • GD&T is a symbolic language used to specify the size, shape, orientation, and location of features on a part.

    • It ensures that parts are manufactured to the correct dimensions and fit together properly.

    • GD&T is used in quality to improve communication between design, engineering, and manufacturing teams.

    • It h...

  • Answered by AI
  • Q2. MS Excel commands used ?
  • Ans. 

    MS Excel commands used?

    • Data sorting and filtering

    • Conditional formatting

    • Pivot tables and charts

    • VLOOKUP and HLOOKUP functions

    • IF and SUM functions

  • Answered by AI
  • Q3. What is the casting process?
  • Ans. 

    Casting is a manufacturing process in which a liquid material is poured into a mold, allowed to solidify, and then removed from the mold.

    • The liquid material can be metal, plastic, or ceramic.

    • The mold is typically made of sand, plaster, or metal.

    • The casting process can be used to create complex shapes and parts.

    • Examples of cast parts include engine blocks, turbine blades, and jewelry.

    • The process can be done using gravit...

  • Answered by AI
  • Q4. What is forging process?
  • Ans. 

    Forging is a manufacturing process where metal is shaped by applying compressive forces using a hammer or press.

    • Metal is heated to a high temperature to make it malleable

    • The metal is then shaped using a hammer or press

    • Forging can be done using different techniques such as open die forging, closed die forging, and seamless ring rolling

    • Forging is used to create high-strength components for various industries such as aero

  • Answered by AI
  • Q5. What is least Count of vernier Calliper?
  • Ans. 

    The least count of a vernier caliper is the smallest measurement that can be read on the scale.

    • The least count is determined by the number of divisions on the vernier scale and the main scale.

    • It is usually expressed in fractions of a millimeter or inch.

    • For example, a vernier caliper with 20 divisions on the vernier scale and 1mm on the main scale has a least count of 0.05mm.

    • The least count is important for accurate mea...

  • Answered by AI
  • Q6. Sheet Meatals Defect?

Interview Preparation Tips

Interview preparation tips for other job seekers - Read all GD&T symbols and All Drawing Read carefully.

Interview Questionnaire 

6 Questions

  • Q1. Tell me about yourself
  • Q2. What is your current role and responsibilities.
  • Q3. How you follow your dwm.
  • Ans. 

    I follow my dwm by regularly reviewing and updating my work plan.

    • I create a detailed work plan at the beginning of each project

    • I regularly review my progress and adjust my plan as needed

    • I prioritize tasks based on their importance and urgency

    • I communicate with my team to ensure we are all on the same page

    • I track my time and make adjustments to my schedule as needed

  • Answered by AI
  • Q4. What is 7 qc and core tools ...
  • Ans. 

    7 QC and Core Tools are quality control methodologies used in manufacturing and service industries.

    • 7 QC tools include Pareto chart, cause-and-effect diagram, control chart, histogram, scatter diagram, flowchart, and check sheet.

    • Core tools include APQP, PPAP, FMEA, MSA, and SPC.

    • These tools help in identifying and solving quality-related issues, improving processes, and reducing defects.

    • They are widely used in industries...

  • Answered by AI
  • Q5. What u Know about quality management system.
  • Ans. 

    Quality management system is a set of policies, processes, and procedures required for planning and execution of quality control.

    • It ensures that products or services meet customer requirements and expectations.

    • It involves continuous improvement and monitoring of processes.

    • ISO 9001 is a widely recognized standard for quality management systems.

    • It includes activities such as quality planning, quality control, and quality...

  • Answered by AI
  • Q6. Reason for job change
  • Ans. 

    Seeking new challenges and opportunities for growth

    • Desire for professional development

    • Looking for a more challenging role

    • Seeking new opportunities to learn and grow

    • Want to broaden skill set and experience

  • Answered by AI

Swaraj Engines Interview FAQs

How many rounds are there in Swaraj Engines Electrical Maintenance Engineer interview?
Swaraj Engines interview process usually has 1 rounds. The most common rounds in the Swaraj Engines interview process are Technical.
What are the top questions asked in Swaraj Engines Electrical Maintenance Engineer interview?

Some of the top questions asked at the Swaraj Engines Electrical Maintenance Engineer interview -

  1. How to do Earthing Te...read more
  2. Use for Megger to resistance ch...read more
  3. motor winding fault ch...read more

Tell us how to improve this page.

Interview Questions from Similar Companies

Tata Motors Interview Questions
4.2
 • 999 Interviews
Maruti Suzuki Interview Questions
4.2
 • 586 Interviews
Hero MotoCorp Interview Questions
4.1
 • 334 Interviews
TVS Motor Interview Questions
4.0
 • 313 Interviews
Bajaj Auto Interview Questions
3.9
 • 267 Interviews
Ashok Leyland Interview Questions
4.1
 • 239 Interviews
Cummins Interview Questions
4.3
 • 231 Interviews
Ford Motor Interview Questions
4.4
 • 145 Interviews
View all

Fast track your campus placements

View all
Diploma Trainee Engineer
28 salaries
unlock blur

₹0 L/yr - ₹0 L/yr

Diploma Engineer
21 salaries
unlock blur

₹0 L/yr - ₹0 L/yr

Mechanical Engineer
20 salaries
unlock blur

₹0 L/yr - ₹0 L/yr

Assistant Engineer
18 salaries
unlock blur

₹0 L/yr - ₹0 L/yr

Associate Engineer
14 salaries
unlock blur

₹0 L/yr - ₹0 L/yr

Explore more salaries
Compare Swaraj Engines with

Mahindra & Mahindra

4.1
Compare

Escorts Kubota Limited

4.1
Compare

Tractors and Farm Equipment

4.1
Compare

Ashok Leyland

4.1
Compare
Did you find this page helpful?
Yes No
write
Share an Interview