Upload Button Icon Add office photos
Engaged Employer

i

This company page is being actively managed by Selec Controls Team. If you also belong to the team, you can get access from here

Selec Controls Verified Tick

Compare button icon Compare button icon Compare

Filter interviews by

Selec Controls R&D Technician Interview Questions, Process, and Tips

Updated 9 Dec 2023

Selec Controls R&D Technician Interview Experiences

1 interview found

Interview experience
4
Good
Difficulty level
Moderate
Process Duration
Less than 2 weeks
Result
Selected Selected

I applied via Referral and was interviewed before Dec 2022. There were 3 interview rounds.

Round 1 - Resume Shortlist 
Pro Tip by AmbitionBox:
Keep your resume crisp and to the point. A recruiter looks at your resume for an average of 6 seconds, make sure to leave the best impression.
View all tips
Round 2 - Aptitude Test 

Well it was my basic introduction and hobbies and stuff

Round 3 - Technical 

(7 Questions)

  • Q1. They Gave me a technical question paper to solve which was of like 3o marks (MCQ)
  • Q2. What is a MOSFET?
  • Ans. 

    A MOSFET (Metal-Oxide-Semiconductor Field-Effect Transistor) is a type of transistor that is widely used in electronic devices.

    • MOSFET is a three-terminal device that can amplify or switch electronic signals.

    • It is made up of a metal gate electrode, an insulating layer of oxide, and a semiconductor channel.

    • MOSFETs are commonly used in integrated circuits (ICs) and power electronics.

    • They are used in various applications s...

  • Answered by AI
  • Q3. Solve this voltage divider circuit
  • Ans. 

    The voltage divider circuit is used to divide a voltage into smaller fractions using resistors.

    • The output voltage can be calculated using the formula Vout = Vin * (R2 / (R1 + R2))

    • The resistors R1 and R2 are connected in series between the input voltage source and ground

    • The voltage across R2 is the output voltage Vout

    • The voltage across R1 is Vin - Vout

    • The ratio of R2 to the total resistance (R1 + R2) determines the outp

  • Answered by AI
  • Q4. How to use a multimeter
  • Ans. 

    A multimeter is a versatile tool used to measure electrical quantities such as voltage, current, and resistance.

    • Start by selecting the appropriate measurement function on the multimeter (e.g., voltage, current, resistance).

    • Ensure the multimeter is set to the correct range for the expected value.

    • Connect the test leads to the appropriate terminals on the multimeter.

    • Place the test leads across the component or circuit bei...

  • Answered by AI
  • Q5. What is an induction motor
  • Ans. 

    An induction motor is an AC electric motor in which power is supplied to the rotor by electromagnetic induction.

    • An induction motor is commonly used in various applications such as industrial machinery, household appliances, and electric vehicles.

    • It operates on the principle of electromagnetic induction, where a rotating magnetic field is created by the stator winding.

    • The rotating magnetic field induces currents in the ...

  • Answered by AI
  • Q6. Any idea about VFDs ?
  • Ans. 

    VFDs, or Variable Frequency Drives, are electronic devices used to control the speed and torque of electric motors.

    • VFDs are commonly used in industrial applications to regulate the speed of motors in machinery.

    • They work by adjusting the frequency and voltage supplied to the motor, allowing for precise control over its speed and torque.

    • VFDs can help save energy by reducing the motor's speed when full power is not requir...

  • Answered by AI
  • Q7. Any idea about EMI EMC test ?
  • Ans. 

    EMI EMC test refers to electromagnetic interference and electromagnetic compatibility testing.

    • EMI EMC test is conducted to assess the ability of electronic devices to function properly in the presence of electromagnetic interference.

    • It involves measuring the electromagnetic emissions from the device under test and ensuring that they comply with regulatory standards.

    • EMC testing is performed to ensure that electronic dev...

  • Answered by AI

Interview Preparation Tips

Topics to prepare for Selec Controls R&D Technician interview:
  • Semiconductor
  • Transistors
  • Electrical Engineering
  • logic gates
  • Ladder Logic
  • Power Supply
  • VFD Drives
Interview preparation tips for other job seekers - go prepared with basic electronics knowledge if you're a fresher,
also try to crack questions from HackerRank.com
this might help a lot

Interview questions from similar companies

I applied via Naukri.com and was interviewed before May 2020. There were 4 interview rounds.

Interview Questionnaire 

1 Question

  • Q1. Simple interview, asking basics of electronics

Interview Preparation Tips

Interview preparation tips for other job seekers - No
Interview experience
4
Good
Difficulty level
Moderate
Process Duration
4-6 weeks
Result
Selected Selected

I applied via Recruitment Consulltant and was interviewed in Feb 2023. There were 2 interview rounds.

Round 1 - Resume Shortlist 
Pro Tip by AmbitionBox:
Keep your resume crisp and to the point. A recruiter looks at your resume for an average of 6 seconds, make sure to leave the best impression.
View all tips
Round 2 - Technical 

(4 Questions)

  • Q1. What is your achievement?
  • Ans. 

    Designed a new product that increased efficiency by 20%

    • Led a team to develop a new product from concept to production

    • Implemented innovative design solutions to improve efficiency

    • Collaborated with cross-functional teams to ensure successful project completion

  • Answered by AI
  • Q2. What problem your faced and how you resolved?
  • Ans. 

    I faced a problem with a design flaw in a product, resolved by conducting thorough testing and redesigning.

    • Identified the design flaw through user feedback and testing

    • Conducted research on alternative design solutions

    • Collaborated with cross-functional teams to implement the redesign

    • Tested the new design thoroughly before implementation

  • Answered by AI
  • Q3. Any rejection by you in previous years and you resolved the rejection issue.
  • Ans. 

    Yes, I faced rejection in a previous job application but used it as motivation to improve my skills and knowledge.

    • I was rejected for a design engineer position due to lack of experience in a specific software, so I took online courses to learn it.

    • I also sought feedback from the interviewer to understand where I fell short and worked on those areas.

    • After improving my skills, I reapplied for similar positions and eventua

  • Answered by AI
  • Q4. Tell me about your current job profile.
  • Ans. 

    I am currently working as a Design Engineer at a manufacturing company.

    • Responsible for designing and developing new products

    • Collaborating with cross-functional teams to ensure product meets requirements

    • Utilizing CAD software for creating detailed designs

    • Conducting testing and analysis to validate design concepts

  • Answered by AI

Interview Preparation Tips

Topics to prepare for Vertiv Design Engineer interview:
  • Sheet Metal Design
Interview preparation tips for other job seekers - Do prepare for current job responsibilities.
Friendly advice - don't join vertiv hadapsar Pune.
New employees 5-6 years experienced are only use and through in R&D pune. Means they have tendency that new engineers should work for 2-3 years only. So they don't need to give promotion and good salary hike.
They will create problems to service to New employees.

I applied via Naukri.com and was interviewed before Sep 2021. There were 2 interview rounds.

Round 1 - Resume Shortlist 
Pro Tip by AmbitionBox:
Keep your resume crisp and to the point. A recruiter looks at your resume for an average of 6 seconds, make sure to leave the best impression.
View all tips
Round 2 - HR 

(4 Questions)

  • Q1. Please introduce yourself
  • Q2. Why are you choose this company for job.
  • Q3. How is the experience of your current company
  • Q4. What's your thought to grow the production and quality of this company.

Interview Preparation Tips

Topics to prepare for Navitasys India Quality Controller interview:
  • Knowledge Management
  • Time Management
Interview preparation tips for other job seekers - It's good for that industry who deserve that employees who want to become a employee in that industry.
Interview experience
5
Excellent
Difficulty level
Moderate
Process Duration
Less than 2 weeks
Result
Selected Selected

I applied via Naukri.com and was interviewed before May 2023. There were 2 interview rounds.

Round 1 - Aptitude Test 

There is an exam which has function related, aptitude related & English related questions

Round 2 - Technical 

(2 Questions)

  • Q1. About DFMEA, DFMEA & PLASTIC DESIGN
  • Q2. Tolerance analysis

Interview Preparation Tips

Interview preparation tips for other job seekers - Please have your basics & foundation strong
Interview experience
5
Excellent
Difficulty level
Easy
Process Duration
Less than 2 weeks
Result
Selected Selected

I applied via Company Website and was interviewed in May 2024. There were 2 interview rounds.

Round 1 - Technical 

(4 Questions)

  • Q1. What is the function of breather in transformer?
  • Ans. 

    Breather in a transformer helps to prevent moisture and dust from entering the transformer tank.

    • Breather allows air to enter and exit the transformer tank as the oil expands and contracts during operation.

    • It contains silica gel or other desiccants to absorb moisture from the air entering the transformer.

    • Prevents the formation of sludge and acids inside the transformer due to moisture contamination.

    • Regular maintenance a...

  • Answered by AI
  • Q2. What is corona in transmission line
  • Ans. 

    Corona in transmission line refers to the phenomenon where electric field strength is highest at the conductor surface.

    • Corona discharge occurs when the electric field strength exceeds the breakdown strength of air.

    • Corona can lead to power loss, audible noise, radio interference, and damage to the transmission line.

    • Examples of equipment used to reduce corona include corona rings and grading rings.

  • Answered by AI
  • Q3. Do you know about 6s, if yes then tell me
  • Ans. 

    6S is a methodology used in lean manufacturing to organize a workplace for efficiency and effectiveness.

    • 6S stands for Sort, Set in order, Shine, Standardize, Sustain, and Safety.

    • It involves organizing the workplace to eliminate waste, improve productivity, and ensure safety.

    • For example, sorting through tools and materials to remove unnecessary items, setting up a visual system for easy access, and regularly cleaning an...

  • Answered by AI
  • Q4. If there is a problem with a product, how will you control it?
  • Ans. 

    I will identify the root cause of the problem, implement corrective actions, and monitor the effectiveness of the solutions.

    • Investigate the issue to determine the root cause

    • Implement corrective actions to address the problem

    • Monitor the effectiveness of the solutions to ensure the problem is resolved

    • Document the entire process for future reference

  • Answered by AI
Round 2 - Experience 

(2 Questions)

  • Q1. What is quality control
  • Ans. 

    Quality control is a process used to ensure that products or services meet specific standards and requirements.

    • Quality control involves monitoring and testing products or services to identify defects or deviations from standards.

    • It aims to prevent defects and ensure consistent quality throughout production.

    • Examples include inspecting products on a production line, conducting tests on samples, and analyzing customer fee...

  • Answered by AI
  • Q2. Tell us about the field in which you have experience

Interview Preparation Tips

Interview preparation tips for other job seekers - Good question answer then salected
Interview experience
4
Good
Difficulty level
-
Process Duration
Less than 2 weeks
Result
No response

I applied via Walk-in and was interviewed in Jul 2024. There was 1 interview round.

Round 1 - Technical 

(5 Questions)

  • Q1. What is current ?
  • Ans. 

    Current is the flow of electric charge in a circuit.

    • Current is measured in Amperes (A)

    • It is the rate of flow of electric charge

    • Current flows from positive to negative terminal in a circuit

    • Examples: Direct current (DC) and Alternating current (AC)

  • Answered by AI
  • Q2. How many parameter we measure in multimeter?
  • Ans. 

    A multimeter typically measures several parameters including voltage, current, and resistance.

    • Voltage

    • Current

    • Resistance

    • Continuity

    • Diode testing

  • Answered by AI
  • Q3. What is difference between cro and functions generator?
  • Ans. 

    A CRO (Cathode Ray Oscilloscope) is used to display and analyze waveforms, while a function generator is used to generate different types of waveforms.

    • CRO is used for visualizing electrical signals in the time domain, while a function generator is used to create specific waveforms like sine, square, triangle, etc.

    • CRO provides a visual representation of the input signal's amplitude, frequency, and phase, while a functio...

  • Answered by AI
  • Q4. What is normal soldering temperature?
  • Ans. 

    Normal soldering temperature typically ranges from 300 to 400 degrees Celsius.

    • Normal soldering temperature ranges from 300 to 400 degrees Celsius

    • Different types of solder may have specific temperature requirements

    • Using a temperature-controlled soldering iron is recommended for precise soldering

    • Excessive heat can damage components and create poor solder joints

  • Answered by AI
  • Q5. Explain different between schematic and block diagram?
  • Ans. 

    Schematic diagrams show the electrical connections and functions of a specific circuit, while block diagrams show the components of a system and their connections.

    • Schematic diagrams focus on the details of individual components and their connections within a circuit.

    • Block diagrams provide an overview of the system by showing the components and their interconnections.

    • Schematic diagrams are commonly used in electronics t...

  • Answered by AI

Skills evaluated in this interview

I applied via Campus Placement and was interviewed before May 2021. There were 3 interview rounds.

Round 1 - Aptitude Test 

Maths, English Grammer, G.k

Round 2 - Technical 

(1 Question)

  • Q1. Based on Resume what we given
Round 3 - One-on-one 

(1 Question)

  • Q1. Sharing Company Knowledge

Interview Preparation Tips

Interview preparation tips for other job seekers - Fresher's are warm welcome to learn & Grow here
Interview experience
5
Excellent
Difficulty level
Moderate
Process Duration
Less than 2 weeks
Result
Selected Selected

I appeared for an interview in Sep 2023.

Round 1 - Technical 

(1 Question)

  • Q1. Please tell us about your experience and what you did in last company?

Interview Preparation Tips

Interview preparation tips for other job seekers - Just need to acquire knowledge skills on daily basis

I applied via Approached by Company

Round 1 - Resume Shortlist 
Pro Tip by AmbitionBox:
Keep your resume crisp and to the point. A recruiter looks at your resume for an average of 6 seconds, make sure to leave the best impression.
View all tips
Round 2 - Aptitude Test 

It is eassy basic electrical then maths

Round 3 - Technical 

(2 Questions)

  • Q1. Basic eletrcal family'baground and branch
  • Q2. Different ac and dc Devices of ac Devices of dc
  • Ans. 

    AC devices use alternating current while DC devices use direct current.

    • AC devices include air conditioners, refrigerators, and washing machines.

    • DC devices include batteries, solar panels, and electronic devices.

    • AC devices are more commonly used in households while DC devices are more commonly used in portable devices.

    • AC devices require a power source that can convert DC to AC while DC devices require a power source tha

  • Answered by AI

Interview Preparation Tips

Interview preparation tips for other job seekers - Two interview after aptitude 1st is non-technical and second Is Basic electrical

Selec Controls Interview FAQs

How many rounds are there in Selec Controls R&D Technician interview?
Selec Controls interview process usually has 3 rounds. The most common rounds in the Selec Controls interview process are Resume Shortlist, Aptitude Test and Technical.
What are the top questions asked in Selec Controls R&D Technician interview?

Some of the top questions asked at the Selec Controls R&D Technician interview -

  1. How to use a multime...read more
  2. what is an induction mo...read more
  3. any idea about EMI EMC tes...read more

Tell us how to improve this page.

Selec Controls R&D Technician Interview Process

based on 1 interview

Interview experience

4
  
Good
View more

Interview Questions from Similar Companies

Flex Interview Questions
4.0
 • 189 Interviews
Navitasys India Interview Questions
4.2
 • 101 Interviews
TE Connectivity Interview Questions
4.1
 • 84 Interviews
Wistron Interview Questions
3.9
 • 82 Interviews
Secure Meters Interview Questions
4.1
 • 69 Interviews
DBG Technology Interview Questions
3.8
 • 64 Interviews
Vertiv Interview Questions
3.9
 • 49 Interviews
View all
Selec Controls R&D Technician Salary
based on 4 salaries
₹2.5 L/yr - ₹3.7 L/yr
At par with the average R&D Technician Salary in India
View more details

Selec Controls R&D Technician Reviews and Ratings

based on 1 review

4.0/5

Rating in categories

5.0

Skill development

5.0

Work-life balance

5.0

Salary

5.0

Job security

2.0

Company culture

5.0

Promotions

3.0

Work satisfaction

Explore 1 Review and Rating
Design Engineer
115 salaries
unlock blur

₹2.5 L/yr - ₹10.5 L/yr

Quality Engineer
65 salaries
unlock blur

₹1.5 L/yr - ₹4.5 L/yr

Test Engineer
47 salaries
unlock blur

₹1 L/yr - ₹3.4 L/yr

PLC Application Engineer
43 salaries
unlock blur

₹1.6 L/yr - ₹6 L/yr

Technician
41 salaries
unlock blur

₹1.5 L/yr - ₹4.5 L/yr

Explore more salaries
Compare Selec Controls with

Bharat Electronics

4.2
Compare

Flex

4.0
Compare

Dixon Technologies

4.0
Compare

ECIL

4.2
Compare
Did you find this page helpful?
Yes No
write
Share an Interview