Upload Button Icon Add office photos

Plastic Omnium

Compare button icon Compare button icon Compare

Filter interviews by

Clear (1)

Plastic Omnium Hardware Engineer Interview Questions and Answers

Updated 27 Apr 2023

Plastic Omnium Hardware Engineer Interview Experiences

2 interviews found

Interview experience
4
Good
Difficulty level
Moderate
Process Duration
Less than 2 weeks
Result
Selected Selected

I applied via LinkedIn and was interviewed in Mar 2023. There were 3 interview rounds.

Round 1 - Resume Shortlist 
Pro Tip by AmbitionBox:
Be truthful in your resume. It is very easy to catch false or lies during the interview by asking basic questions.
View all Resume tips
Round 2 - One-on-one 

(3 Questions)

  • Q1. Selection of mosfet in SMPs
  • Ans. 

    MOSFET selection in SMPs is based on various factors like voltage, current, switching speed, and thermal considerations.

    • Consider the maximum voltage and current requirements of the circuit

    • Choose a MOSFET with low on-resistance to minimize power loss

    • Select a MOSFET with fast switching speed to reduce switching losses

    • Ensure proper thermal management to prevent overheating

    • Examples of MOSFETs commonly used in SMPs are IRF5

  • Answered by AI
  • Q2. Transistor as a Switch
  • Ans. 

    Transistor can be used as a switch by controlling the base current.

    • Transistor operates in two modes - cutoff and saturation.

    • In cutoff mode, no current flows through the transistor.

    • In saturation mode, maximum current flows through the transistor.

    • By controlling the base current, we can switch the transistor between these two modes.

    • Transistor switches are widely used in digital circuits and power electronics.

  • Answered by AI
  • Q3. Opamp amplifier different applications
  • Ans. 

    Opamp amplifiers are used in various applications such as audio amplification, instrumentation, and signal conditioning.

    • Opamp amplifiers are commonly used in audio amplification circuits to increase the amplitude of audio signals.

    • In instrumentation applications, opamp amplifiers are used to amplify small signals from sensors or transducers.

    • Opamp amplifiers are also used in signal conditioning circuits to filter, rectif...

  • Answered by AI
Round 3 - HR 

(1 Question)

  • Q1. Aptitute test mental ability
Round 1 - Technical 

(1 Question)

  • Q1. Focus on DC DC converter like Boost, Buck, Sepic

Interview Preparation Tips

Interview preparation tips for other job seekers - Focus on DC DC converter like buck, boost, sepic. Basic knowledge of component selection

Hardware Engineer Interview Questions Asked at Other Companies

asked in Qualcomm
Q1. How many ways would one arrange sets of coloured balls, the first ... read more
asked in Qualcomm
Q2. How do you implement the overlap-add method of convolution?
asked in Qualcomm
Q3. How do you obtain the bit-rate for quantization of a band-limited ... read more
asked in Qualcomm
Q4. How do you obtain the in-phase and quadrature components of a rea ... read more
asked in Qualcomm
Q5. How do you implement interpolation in discrete-time domain?

Interview questions from similar companies

I applied via Naukri.com and was interviewed in May 2020. There were 4 interview rounds.

Interview Questionnaire 

3 Questions

  • Q1. What are the die casting and machining defects?
  • Ans. 

    Die casting and machining defects are common in manufacturing processes.

    • Die casting defects include porosity, shrinkage, cold shuts, and flash.

    • Machining defects include burrs, chatter marks, and tool marks.

    • Die casting defects can be caused by improper temperature, pressure, or metal flow.

    • Machining defects can be caused by dull tools, improper speeds and feeds, or poor fixturing.

    • Defects can lead to part failure, reduced

  • Answered by AI
  • Q2. What is the formula of filling and high speed ratio?
  • Ans. 

    Filling and high speed ratio formula is used to calculate the filling time of a container with a specific volume of liquid at a given flow rate.

    • Filling and high speed ratio formula is V/Q

    • V is the volume of the container and Q is the flow rate of the liquid

    • The formula is used to determine the time it takes to fill a container with a specific volume of liquid at a given flow rate

    • The higher the flow rate, the faster the c

  • Answered by AI
  • Q3. Why do u want to join Motherson?

Interview Preparation Tips

Interview preparation tips for other job seekers - Be always job needy in front of interviewer.

I was interviewed in Jul 2020.

Interview Questionnaire 

1 Question

  • Q1. Waht is your achievements
  • Ans. 

    I have achieved several milestones throughout my career as a Senior Engineer.

    • Successfully led a team of engineers to develop and implement a new software system, resulting in a 20% increase in efficiency.

    • Received recognition for designing and implementing a cost-effective solution that reduced production downtime by 30%.

    • Contributed to the development of a groundbreaking technology that revolutionized the industry, lead...

  • Answered by AI

Interview Preparation Tips

Interview preparation tips for other job seekers - All most 3 Rounds they conducted, they taken 3 days for every round and they taken allmost 3 months to select... For learners this company was good...

I applied via Naukri.com and was interviewed in Oct 2020. There were 3 interview rounds.

Interview Questionnaire 

3 Questions

  • Q1. Previous company job profile.
  • Q2. Plc related questions
  • Q3. Family background

I applied via Recruitment Consultant and was interviewed before Oct 2020. There were 3 interview rounds.

Interview Questionnaire 

5 Questions

  • Q1. Which vehicle license you have?
  • Ans. 

    I have a valid driver's license for both cars and motorcycles.

    • I have a Class C license for cars

    • I also have a Class M license for motorcycles

    • I have a clean driving record with no accidents or violations

  • Answered by AI
  • Q2. What is CBS & ABS
  • Q3. Which segment of bike you ride
  • Ans. 

    I ride a road bike for commuting and a mountain bike for leisure.

    • I prefer road bikes for their speed and efficiency on paved roads.

    • I enjoy mountain biking for the challenge and adventure of off-road trails.

    • I also have experience with hybrid bikes for their versatility.

    • I prioritize safety and always wear a helmet and follow traffic laws.

    • I have participated in charity rides and group rides for fun and community.

  • Answered by AI
  • Q4. How you do the vehicle testing
  • Ans. 

    Vehicle testing involves various methods to ensure safety, performance, and compliance with regulations.

    • Testing can include physical tests such as crash tests, durability tests, and performance tests.

    • Simulation and modeling can also be used to test vehicle components and systems.

    • Testing must comply with regulations set by organizations such as the National Highway Traffic Safety Administration (NHTSA) and the European

  • Answered by AI
  • Q5. Which type of Homologation testing you do?
  • Ans. 

    We conduct various types of homologation testing depending on the product and its intended market.

    • We conduct safety testing to ensure compliance with local regulations.

    • We perform emissions testing to ensure compliance with environmental regulations.

    • We conduct performance testing to ensure the product meets the required standards.

    • We also conduct durability testing to ensure the product can withstand the expected wear an...

  • Answered by AI

Interview Preparation Tips

Interview preparation tips for other job seekers - That question were ask me for vehicle testing engineer & for test rider position

I applied via Walk-in and was interviewed in May 2022. There were 4 interview rounds.

Round 1 - Resume Shortlist 
Pro Tip by AmbitionBox:
Keep your resume crisp and to the point. A recruiter looks at your resume for an average of 6 seconds, make sure to leave the best impression.
View all Resume tips
Round 2 - Technical 

(3 Questions)

  • Q1. Production related questions
  • Q2. Working flow rated questions
  • Q3. Any other factory related
Round 3 - HR 

(1 Question)

  • Q1. Salary related questions
Round 4 - Group Discussion 
Pro Tip by AmbitionBox:
Don’t treat group discussions as an argument. Group discussion is about reaching a meaningful conclusion.
View all GD tips

Interview Preparation Tips

Interview preparation tips for other job seekers - Need good job for my skills and production related.

I applied via Naukri.com and was interviewed in May 2021. There were 3 interview rounds.

Interview Questionnaire 

2 Questions

  • Q1. Technical questions regarding GDC process, rejection control and analysis..
  • Q2. Hypothetical questions, besed on situation handling, manpower handling and decision making

Interview Preparation Tips

Interview preparation tips for other job seekers - Be specific and speak confident
Interview experience
4
Good
Difficulty level
Moderate
Process Duration
2-4 weeks
Result
Selected Selected

I applied via Approached by Company and was interviewed in Jun 2022. There were 4 interview rounds.

Round 1 - Resume Shortlist 
Pro Tip by AmbitionBox:
Keep your resume crisp and to the point. A recruiter looks at your resume for an average of 6 seconds, make sure to leave the best impression.
View all Resume tips
Round 2 - HR 

(1 Question)

  • Q1. General Introduction about self and family members Work experience And reason for change
Round 3 - Group Discussion 

Discussion with Different Process OWNER HOD QA, Engg. Purchase for technical....and previous handling work...

Round 4 - Technical 

(1 Question)

  • Q1. Technical discussion with TOP management PLANT HEAD AND CORPORATE HR HEAD. related assign job and past experiences of SQA and development profile.

Interview Preparation Tips

Interview preparation tips for other job seekers - Always learn more and more about work that u are doing...and excecution in disciplinary manner... Don't think about interview it is just a glance of your knowledge which u have gain during working.........

Don't explain extravagancy things in discussion.....

Be careful.

I applied via Walk-in and was interviewed before Dec 2021. There were 3 interview rounds.

Round 1 - Resume Shortlist 
Pro Tip by AmbitionBox:
Keep your resume crisp and to the point. A recruiter looks at your resume for an average of 6 seconds, make sure to leave the best impression.
View all Resume tips
Round 2 - Technical 

(2 Questions)

  • Q1. Write and explain GD&T symbols?
  • Ans. 

    GD&T symbols are used to specify the geometric requirements of a part or assembly.

    • GD&T stands for Geometric Dimensioning and Tolerancing

    • Symbols include: flatness, circularity, perpendicularity, concentricity, position, and more

    • Each symbol has a specific meaning and is used to communicate precise engineering requirements

    • GD&T is used in industries such as aerospace, automotive, and manufacturing

    • Example: A position symbol...

  • Answered by AI
  • Q2. Explain Cp, Cpk & Pp, Ppk?
  • Ans. 

    Cp, Cpk, Pp, and Ppk are statistical process control indices used to measure process capability and performance.

    • Cp and Cpk measure how well a process meets its specifications, with Cpk being more accurate for non-centered processes.

    • Pp and Ppk measure how well a process performs relative to its natural variation, with Ppk being more accurate for non-centered processes.

    • All four indices are calculated using the process me...

  • Answered by AI
Round 3 - Technical 

(1 Question)

  • Q1. Related to GD&T, CNC programming knowledge, SPC, Fixture design and development, Tool design and development.

Interview Preparation Tips

Interview preparation tips for other job seekers - Willing to work extra hours and ready to compromise family members.
Contribute & help others!
anonymous
You can choose to be anonymous

Plastic Omnium Interview FAQs

How many rounds are there in Plastic Omnium Hardware Engineer interview?
Plastic Omnium interview process usually has 2 rounds. The most common rounds in the Plastic Omnium interview process are Technical, Resume Shortlist and One-on-one Round.
What are the top questions asked in Plastic Omnium Hardware Engineer interview?

Some of the top questions asked at the Plastic Omnium Hardware Engineer interview -

  1. Opamp amplifier different applicati...read more
  2. Selection of mosfet in S...read more
  3. Transistor as a Swi...read more

Recently Viewed

INTERVIEWS

BrightCHAMPS

No Interviews

INTERVIEWS

BrightCHAMPS

No Interviews

INTERVIEWS

Plastic Omnium

No Interviews

SALARIES

Plastic Omnium

INTERVIEWS

Samsung SDS

No Interviews

SALARIES

99acres

INTERVIEWS

The United States Pharmacopeia

No Interviews

INTERVIEWS

BrightCHAMPS

No Interviews

INTERVIEWS

Paytm

No Interviews

INTERVIEWS

Plastic Omnium

No Interviews

Tell us how to improve this page.

Plastic Omnium Hardware Engineer Interview Process

based on 1 interview

Interview experience

4
  
Good
View more

Interview Questions from Similar Companies

Varroc Group Interview Questions
3.6
 • 176 Interviews
UNO Minda Interview Questions
4.0
 • 169 Interviews
Ford Motor Interview Questions
4.4
 • 145 Interviews
Yamaha Motor Interview Questions
4.1
 • 65 Interviews
Volvo Interview Questions
4.1
 • 63 Interviews
CNH Industrial Interview Questions
3.8
 • 56 Interviews
Bharat Forge Interview Questions
3.9
 • 55 Interviews
View all
Project Engineer
125 salaries
unlock blur

₹0 L/yr - ₹0 L/yr

Assistant Manager
87 salaries
unlock blur

₹0 L/yr - ₹0 L/yr

Design Engineer
58 salaries
unlock blur

₹0 L/yr - ₹0 L/yr

Graduate Engineer Trainee (Get)
53 salaries
unlock blur

₹0 L/yr - ₹0 L/yr

Senior Engineer
51 salaries
unlock blur

₹0 L/yr - ₹0 L/yr

Explore more salaries
Compare Plastic Omnium with

Bharat Forge

3.9
Compare

Samvardhana Motherson Group

3.7
Compare

Endurance Technologies

3.9
Compare

Varroc Group

3.6
Compare
Did you find this page helpful?
Yes No
write
Share an Interview