Upload Button Icon Add office photos

MUNDRA SOLAR TECHNOPARK

Compare button icon Compare button icon Compare

Filter interviews by

MUNDRA SOLAR TECHNOPARK Maintenance Engineer Interview Questions and Answers

Updated 1 May 2022

MUNDRA SOLAR TECHNOPARK Maintenance Engineer Interview Experiences

1 interview found

I applied via Approached by Company and was interviewed in Apr 2022. There were 2 interview rounds.

Round 1 - Resume Shortlist 
Pro Tip by AmbitionBox:
Don’t add your photo or details such as gender, age, and address in your resume. These details do not add any value.
View all tips
Round 2 - Technical 

(3 Questions)

  • Q1. What is diode?, How to check diode true or false with multimeter
  • Ans. 

    A diode is an electronic component that allows current to flow in one direction only.

    • A diode has two terminals: an anode and a cathode.

    • To check if a diode is true or false, set the multimeter to the diode test mode.

    • Connect the red probe to the anode and the black probe to the cathode.

    • If the diode is good, the multimeter will show a voltage drop of around 0.6 to 0.7 volts.

    • If the diode is bad, the multimeter will show no...

  • Answered by AI
  • Q2. What is your college project
  • Q3. Difference between digital and analog
  • Ans. 

    Digital refers to discrete values while analog refers to continuous values.

    • Digital signals are represented by binary code (0s and 1s) while analog signals are represented by continuous waves.

    • Digital signals are less prone to noise and distortion while analog signals are more susceptible to interference.

    • Examples of digital devices include computers, smartphones, and digital cameras while examples of analog devices inclu

  • Answered by AI

Interview Preparation Tips

Interview preparation tips for other job seekers - Communication, behaviour and Give right answer

Interview questions from similar companies

I applied via Referral and was interviewed in Mar 2021. There were 3 interview rounds.

Interview Questionnaire 

2 Questions

  • Q1. About Process related to Assembly line
  • Q2. Details of assembly line sequence
  • Ans. 

    The assembly line sequence involves a step-by-step process of assembling parts to create a final product.

    • The process starts with the arrival of raw materials

    • Parts are then assembled in a specific order

    • Quality checks are performed at various stages

    • The final product is packaged and shipped

    • Efficiency and safety are key considerations throughout the process

  • Answered by AI

Interview Preparation Tips

Interview preparation tips for other job seekers - No hard question only basic related to design and assembly process.

I applied via Recruitment Consultant and was interviewed before Jan 2021. There were 3 interview rounds.

Interview Questionnaire 

3 Questions

  • Q1. All technical parameters regarding equipment
  • Q2. Mention the types of pump’s
  • Ans. 

    There are various types of pumps used in mechanical engineering.

    • Centrifugal pumps

    • Positive displacement pumps

    • Axial flow pumps

    • Mixed flow pumps

    • Jet pumps

  • Answered by AI
  • Q3. Explain the type’s of maintenance
  • Ans. 

    Types of maintenance include corrective, preventive, predictive, and proactive maintenance.

    • Corrective maintenance involves fixing a problem after it has occurred.

    • Preventive maintenance involves scheduled maintenance to prevent problems from occurring.

    • Predictive maintenance involves using data and analysis to predict when maintenance is needed.

    • Proactive maintenance involves identifying and addressing potential issues be...

  • Answered by AI

Interview Preparation Tips

Interview preparation tips for other job seekers - Just believe on your self and be confident

Service Engineer Interview Questions & Answers

Liebherr user image SMRITI KISHOR DAS

posted on 18 Apr 2022

I applied via Naukri.com and was interviewed before Apr 2021. There were 2 interview rounds.

Round 1 - Technical 

(1 Question)

  • Q1. Basics Hydraulics, Basic electrical, Sensors, PLC
Round 2 - HR 

(8 Questions)

  • Q1. What are your strengths and weaknesses?
  • Q2. Why are you looking for a change?
  • Q3. Why should we hire you?
  • Q4. What are your salary expectations?
  • Q5. What is your family background?
  • Q6. Share details of your previous job.
  • Q7. Where do you see yourself in 5 years?
  • Q8. Tell me about yourself.

Interview Preparation Tips

Topics to prepare for Liebherr Service Engineer interview:
  • Hydraulics
Interview preparation tips for other job seekers - Keep motivated yourself whatever the situation is.

I applied via Approached by Company and was interviewed before May 2021. There was 1 interview round.

Round 1 - Technical 

(1 Question)

  • Q1. Basic hydraulic symbols

Interview Preparation Tips

Interview preparation tips for other job seekers - This is worst management don't join this company.
No any career growth once joined this company
Interview process is basic hydraulic symbols only.

Interview Questionnaire 

5 Questions

  • Q1. Tell me about yourself?
  • Ans. 

    I am a Service Engineer with expertise in troubleshooting and repairing complex machinery.

    • Experienced in diagnosing and resolving technical issues in industrial equipment

    • Proficient in using diagnostic tools and software to identify problems

    • Skilled in performing maintenance and repairs on various types of machinery

    • Strong problem-solving and communication skills

    • Ability to work independently and under pressure

    • Example: Suc...

  • Answered by AI
  • Q2. Why hydraulics Ram has different speed in head side and rod Side?
  • Ans. 

    The speed difference in a hydraulic ram is due to the difference in effective areas on the head side and rod side.

    • The head side of the ram has a larger effective area, resulting in slower speed.

    • The rod side of the ram has a smaller effective area, resulting in faster speed.

    • This speed difference is a result of the hydraulic pressure acting on different areas.

    • The speed ratio between the head side and rod side can be calc...

  • Answered by AI
  • Q3. What is the purpose of pressure relief valve?
  • Ans. 

    A pressure relief valve is used to protect equipment and systems from excessive pressure by releasing the pressure when it exceeds a certain limit.

    • Prevents damage to equipment and systems

    • Ensures safety of personnel

    • Maintains system integrity

    • Prevents explosions or ruptures

    • Relieves excess pressure by opening and releasing fluid or gas

    • Commonly used in boilers, pressure vessels, pipelines, and hydraulic systems

  • Answered by AI
  • Q4. What is orifice?
  • Ans. 

    An orifice is a small opening or hole through which fluid or gas can flow.

    • Orifices are commonly used in various industries, such as plumbing, engineering, and manufacturing.

    • They are often used to control the flow rate of fluids or gases.

    • Orifices can be found in devices like nozzles, valves, and flow meters.

    • The size of an orifice determines the flow rate and pressure drop across it.

    • Examples of orifices include the tiny ...

  • Answered by AI
  • Q5. Why you looking for a job change?
  • Ans. 

    I am looking for a job change to explore new opportunities and challenges.

    • Seeking career growth and advancement

    • Wanting to work in a different industry or with different technologies

    • Desire for a better work-life balance

    • Relocation or proximity to family

    • Unsatisfactory current job situation

  • Answered by AI

Interview Preparation Tips

Interview preparation tips for other job seekers - Just give your introduction very simple short and sweet it's not to be so lengthy.
And the technical round is very simple as always. It consists of mainly Basics.
So don't worry...!!

Best of Luck...!!

I applied via Naukri.com and was interviewed before May 2018. There were 5 interview rounds.

Interview Questionnaire 

4 Questions

  • Q1. Explain about open loop & close loop operation in hydraulic system.
  • Ans. 

    Open loop and closed loop are two modes of operation in hydraulic systems.

    • Open loop operation: The hydraulic system operates without feedback control. The output is not adjusted based on the system's performance.

    • Closed loop operation: The hydraulic system uses feedback control to adjust the output based on the system's performance.

    • Open loop systems are simpler and less expensive, but they lack precision and accuracy.

    • Cl...

  • Answered by AI
  • Q2. Explain about Starting circuit.
  • Ans. 

    The starting circuit is responsible for initiating the engine's operation.

    • The starting circuit consists of components such as the battery, starter motor, ignition switch, and solenoid.

    • When the ignition switch is turned on, it sends a signal to the solenoid, which then engages the starter motor.

    • The starter motor uses electrical energy from the battery to turn the engine's crankshaft, starting the combustion process.

    • Once...

  • Answered by AI
  • Q3. Why should we hire you ?
  • Ans. 

    I am a highly skilled and experienced service engineer with a proven track record of successfully troubleshooting and resolving complex technical issues.

    • I have a strong technical background and extensive experience in diagnosing and repairing equipment.

    • I am a quick learner and can adapt to new technologies and processes easily.

    • I have excellent communication skills and can effectively communicate with customers and team...

  • Answered by AI
  • Q4. What is your core values ?
  • Ans. 

    My core values include integrity, accountability, and continuous learning.

    • Integrity: I believe in always doing the right thing, even when no one is watching.

    • Accountability: I take ownership of my actions and responsibilities.

    • Continuous learning: I strive to constantly improve my skills and knowledge.

    • Example: I once discovered a mistake in a project I was working on, and instead of ignoring it, I took responsibility and...

  • Answered by AI

Interview Preparation Tips

Round: Test
Experience: Questions based upon technical knowledge like engine, basic electrical & basic hydraulics.

General Tips: You should have deep knowledge about hydraulics system & DC electrics.
Skills: Communication, Body Language, Problem Solving, Analytical Skills, Leadership, Presentation Skills, Time Management, Decision Making Skills
Duration: 1-3 Months

I applied via Walk-in and was interviewed in Jun 2021. There was 1 interview round.

Interview Questionnaire 

3 Questions

  • Q1. What is varnier caliper least count
  • Ans. 

    The least count of a vernier caliper is the smallest measurement that can be accurately read on the scale.

    • The least count is determined by the number of divisions on the main scale and the vernier scale.

    • It is calculated by dividing the smallest division on the main scale by the number of divisions on the vernier scale.

    • For example, if the smallest division on the main scale is 0.1 mm and the vernier scale has 10 divisio...

  • Answered by AI
  • Q2. What is your father and mother work
  • Q3. What is your qualifications

Interview Preparation Tips

Interview preparation tips for other job seekers - KTTM company is very strictly document verification chaking and time maintain rules and regulations strictly followed

Service Engineer Interview Questions & Answers

Liebherr user image SURYAKANTA DEHURY

posted on 23 Feb 2025

Interview experience
4
Good
Difficulty level
-
Process Duration
-
Result
-
Round 1 - Technical 

(1 Question)

  • Q1. Engine hydraulic electrical
Interview experience
4
Good
Difficulty level
Moderate
Process Duration
Less than 2 weeks
Result
Selected Selected

I applied via Company Website and was interviewed before Jan 2022. There were 3 interview rounds.

Round 1 - Resume Shortlist 
Pro Tip by AmbitionBox:
Keep your resume crisp and to the point. A recruiter looks at your resume for an average of 6 seconds, make sure to leave the best impression.
View all tips
Round 2 - Technical 

(2 Questions)

  • Q1. Draw a basic Hydraulic circuit and expain ?
  • Ans. 

    A hydraulic circuit is a system that uses pressurized fluid to transmit power.

    • A hydraulic pump is used to create pressure in the fluid.

    • Valves control the flow of fluid through the circuit.

    • Actuators, such as cylinders or motors, convert the fluid pressure into mechanical force.

    • A reservoir stores the fluid and a filter removes contaminants.

    • Examples include excavators, cranes, and hydraulic presses.

  • Answered by AI
  • Q2. What is tappet setting required in engines ?
  • Ans. 

    Tappet setting is the process of adjusting the clearance between the tappet and the valve stem in an engine.

    • Tappet setting ensures proper valve timing and prevents engine damage.

    • It involves adjusting the clearance between the tappet and the valve stem using a feeler gauge.

    • The correct tappet setting varies depending on the engine model and manufacturer.

    • Incorrect tappet setting can cause engine noise, poor performance, a...

  • Answered by AI
Round 3 - HR 

(1 Question)

  • Q1. Tell me about yourself

Interview Preparation Tips

Interview preparation tips for other job seekers - Study technical like electrical and hydraulics thorughly

MUNDRA SOLAR TECHNOPARK Interview FAQs

How many rounds are there in MUNDRA SOLAR TECHNOPARK Maintenance Engineer interview?
MUNDRA SOLAR TECHNOPARK interview process usually has 2 rounds. The most common rounds in the MUNDRA SOLAR TECHNOPARK interview process are Resume Shortlist and Technical.
What are the top questions asked in MUNDRA SOLAR TECHNOPARK Maintenance Engineer interview?

Some of the top questions asked at the MUNDRA SOLAR TECHNOPARK Maintenance Engineer interview -

  1. What is diode?, How to check diode true or false with multime...read more
  2. Difference between digital and ana...read more

Tell us how to improve this page.

MUNDRA SOLAR TECHNOPARK Maintenance Engineer Salary
based on 5 salaries
₹2 L/yr - ₹2.7 L/yr
41% less than the average Maintenance Engineer Salary in India
View more details

MUNDRA SOLAR TECHNOPARK Maintenance Engineer Reviews and Ratings

based on 4 reviews

4.4/5

Rating in categories

4.0

Skill development

2.5

Work-life balance

3.5

Salary

2.9

Job security

3.5

Company culture

3.1

Promotions

3.1

Work satisfaction

Explore 4 Reviews and Ratings
Deputy Associate
62 salaries
unlock blur

₹1.6 L/yr - ₹2.6 L/yr

Diploma Trainee Engineer
42 salaries
unlock blur

₹1.5 L/yr - ₹2.5 L/yr

Associate
28 salaries
unlock blur

₹1.3 L/yr - ₹3 L/yr

Operator
23 salaries
unlock blur

₹1.4 L/yr - ₹2.4 L/yr

Team Lead
22 salaries
unlock blur

₹2 L/yr - ₹3 L/yr

Explore more salaries
Compare MUNDRA SOLAR TECHNOPARK with

Ge India Industrial

4.3
Compare

Gilbarco Veeder Root

3.8
Compare

Kirloskar Toyota Textile Machinery

4.5
Compare

L&T–MHI Power Boilers

4.0
Compare
Did you find this page helpful?
Yes No
write
Share an Interview