Mahindra & Mahindra Trainee Mechanical Engineer Interview Questions and Answers

Q1. Mechanical engine four wheeler
Add your answer
Q2. Mechanical engine four wheeler
Add your answer
Q3. Clutch overhaul and paid services break paad and
Add your answer
Q4. Timing chain and diesel engines
Add your answer
Q5. Engine mounting and service engine
Add your answer

Behaviour of mechanical

Q1. What is the capacity of diesel and petrol
Ans. 
Diesel has higher energy density than petrol, resulting in better fuel efficiency.
• Diesel has a higher energy density than petrol, meaning it can provide more energy per unit volume.

• Petrol is more volatile and burns faster than diesel.

• The capacity of diesel and petrol tanks in vehicles can vary depending on the size of the vehicle and its fuel efficiency.

• For example, a typical car may have a petrol tank capacity of arou...read more
Answered by AI
Add your answer
Q2. Difference b/w petrol engine & diesel engine
Ans. 
Petrol engines use spark ignition, while diesel engines use compression ignition.
• Petrol engines use a spark plug to ignite the fuel-air mixture, while diesel engines rely on compression to ignite the fuel.

• Petrol engines are lighter and more responsive, while diesel engines are more fuel-efficient and have higher torque.

• Petrol engines are more common in cars and motorcycles, while diesel engines are often used in trucks
Answered by AI
Add your answer
Q3. What is meant by LNTD
Ans. 
LNTD stands for Logarithmic Mean Temperature Difference.
• LNTD is a term used in heat transfer calculations to determine the overall temperature difference between two fluids in a heat exchanger.

• It is calculated using the formula LNTD = (ΔT1 - ΔT2) / ln(ΔT1 / ΔT2), where ΔT1 and ΔT2 are the temperature differences at the two ends of the heat exchanger.

• LNTD is important in designing efficient heat exchangers to maximize h...read more
Answered by AI
Add your answer

Practice from indiabix

Q1. What is stress ,draw stree strain diagram
Ans. 
Stress is a measure of the internal resistance of a material to deformation, while a stress-strain diagram shows the relationship between stress and strain.
• Stress is the force applied per unit area on a material, measured in units like Pascals or psi.

• Strain is the measure of deformation of a material in response to stress, typically expressed as a percentage.

• A stress-strain diagram plots stress on the y-axis and strain...read more
Answered by AI
Add your answer
Q2. Draw different cycles of IC engine and explain in detail
Ans. 
Different cycles of IC engines include Otto, Diesel, Dual, and Atkinson cycles.
• Otto cycle: Ideal cycle for spark-ignition engines, consisting of four processes - isentropic compression, constant volume heat addition, isentropic expansion, and constant volume heat rejection.

• Diesel cycle: Ideal cycle for compression-ignition engines, with four processes - isentropic compression, constant pressure heat addition, isentropi...read more
Answered by AI
Add your answer

Q1. Tractor all repair
Add your answer
Q2. Service engine repair all model Swaraj Tractor
Add your answer

Q1. Tractor all repair
Add your answer
Q2. Swaraj Tractor all repair engine
Add your answer

Yes i want aptitude test plz share on me email
1 more round
Hard working
Embition
Cansantrated

Q1. Mechanical engineering Quality assurance
Add your answer
Q2. Which type of ic engine
Ans. 
Internal combustion engines are classified into two main types: spark ignition (SI) engines and compression ignition (CI) engines.
• Spark ignition (SI) engines use a spark plug to ignite the fuel-air mixture, commonly found in gasoline engines.

• Compression ignition (CI) engines rely on the heat generated by compressing the air in the cylinder to ignite the fuel, commonly found in diesel engines.

• Each type of engine has its...read more
Answered by AI
Add your answer
Q3. Instrumental calibration
Add your answer
Q4. How do you use instrument
Ans. 
Instruments are used in various ways in mechanical engineering, such as for measuring, testing, and analyzing different parameters.
• Instruments are used for measuring various parameters like temperature, pressure, flow rate, etc.

• Instruments are used for testing the performance of mechanical systems and components.

• Instruments are used for analyzing data and making informed decisions based on the results.

• Examples include ...read more
Answered by AI
Add your answer
Q5. What about a quality control
Ans. 
Quality control is essential in ensuring products meet standards and specifications.
• Quality control involves monitoring and testing products to ensure they meet specified standards.

• It helps identify defects or issues early in the production process.

• Quality control can involve inspections, testing, and audits to ensure consistency and reliability.

• Examples include checking dimensions of a part, testing the strength of a
Answered by AI
Add your answer

Q1. What ppc and pneumatic
Ans. 
PPC stands for Programmable Logic Controller and Pneumatic refers to the use of compressed air in mechanical systems.
• PPC is a type of industrial computer used to control manufacturing processes.

• Pneumatic systems use compressed air to power mechanical components like cylinders and valves.

• Both PPC and pneumatic systems are commonly used in industrial maintenance and automation.

• Examples of pneumatic systems include air br...read more
Answered by AI
Add your answer
Q2. Difference between motor and Generator
Ans. 
Motors convert electrical energy into mechanical energy while generators convert mechanical energy into electrical energy.
• Motors use electrical energy to create a magnetic field that produces rotational motion.

• Generators use rotational motion to create a magnetic field that produces electrical energy.

• Motors are used in appliances, vehicles, and industrial machinery.

• Generators are used in power plants, wind turbines, an
Answered by AI
Add your answer

Q1. What is your bachelor degree ?
Add your answer
Q2. What is your interest in cars?
Ans. 
I have always been fascinated by the intricate design and engineering of cars, from their engines to their aerodynamics.
• I enjoy learning about different car manufacturers and their unique technologies.

• I like to attend car shows and track events to see the latest models and innovations.

• I have worked on restoring classic cars as a hobby, gaining hands-on experience with mechanical systems.
Answered by AI
Add your answer

Q1. 7qc tool 5s PFMA Red bin analysis
Add your answer