Filter interviews by
I applied via Campus Placement and was interviewed before Mar 2020. There was 1 interview round.
Top trending discussions
I applied via Referral and was interviewed in Feb 2021. There was 1 interview round.
Star delta connection is a method of connecting three-phase electrical motors.
It is used to reduce the starting current of the motor.
In star connection, the motor windings are connected in a triangle and in delta connection, they are connected in a star.
The switch from star to delta is done using a contactor.
The motor runs at a lower voltage in star connection and at full voltage in delta connection.
DG stands for Diesel Generator. It is a backup power source that works by converting diesel fuel into electricity.
DG is commonly used in areas with frequent power outages or in remote locations where there is no access to the power grid.
It consists of a diesel engine and an alternator that work together to generate electricity.
Maintenance of DG includes regular oil and filter changes, checking the battery and coolant l...
A transformer is an electrical device that transfers electrical energy between two or more circuits through electromagnetic induction.
Transformers are used to increase or decrease the voltage of an alternating current (AC) power supply.
They work on the principle of electromagnetic induction, where a changing magnetic field induces a voltage in a coil of wire.
The ratings of a transformer include its voltage rating, curr...
The voltage between neutral to ground or earth is ideally zero, but can vary depending on the electrical system and grounding practices.
In a properly grounded electrical system, the voltage between neutral and ground should be zero.
However, in some cases, such as when there is a fault in the system or improper grounding practices, the voltage can be higher.
The voltage between neutral and ground can also vary depending ...
Efficiency of a boiler can be increased by improving insulation, optimizing combustion, and regular maintenance.
Improve insulation to reduce heat loss
Optimize combustion by adjusting air-to-fuel ratio and using efficient burners
Regular maintenance to clean and repair components
Use economizers to recover waste heat
Upgrade to high-efficiency boilers
Implement energy management systems to monitor and control boiler operati
posted on 28 Jun 2021
posted on 26 Sep 2021
I applied via Recruitment Consultant and was interviewed in Mar 2021. There was 1 interview round.
posted on 20 Nov 2022
I applied via Walk-in and was interviewed in May 2022. There were 3 interview rounds.
1 millimetre is equal to 1000 micron.
1 millimetre is a unit of length in the metric system.
Micron is a unit of length equal to one millionth of a meter.
To convert millimetres to microns, multiply the value by 1000.
For example, 5 millimetres is equal to 5000 microns.
CNC stands for Computer Numerical Control. 1 mm is equal to 1000 microns.
CNC machines are automated tools that use pre-programmed software to control movement of tools and machinery.
Micron is a unit of measurement used to measure very small distances, equal to one millionth of a meter.
1 mm is equal to 1000 microns.
Experienced production engineer with a background in mechanical engineering and a passion for optimizing manufacturing processes.
Graduated with a degree in Mechanical Engineering
Worked for 5 years in the manufacturing industry
Implemented lean manufacturing principles to improve production efficiency
Led a team in reducing production costs by 15% through process optimization
Knocking is an abnormal combustion phenomenon in internal combustion engines.
Knocking occurs when the air-fuel mixture in the engine's cylinders ignites prematurely or unevenly.
It produces a knocking or pinging sound, which can cause damage to the engine if not addressed.
Factors contributing to knocking include low octane fuel, high engine temperatures, and incorrect ignition timing.
I am a dedicated and experienced Production Engineer with a strong background in manufacturing processes and quality control.
Bachelor's degree in Mechanical Engineering
5+ years of experience in production engineering
Proficient in CAD software and manufacturing processes
Led a team to improve production efficiency by 20% in my previous role
As a Production Engineer, my role involves overseeing the manufacturing process, ensuring efficiency, quality, and safety.
Oversee the manufacturing process to ensure efficiency and quality
Identify and troubleshoot any issues that arise during production
Implement improvements to enhance productivity and reduce costs
Collaborate with other departments to optimize processes and meet production goals
General Aptitude with reasoning
posted on 31 Jan 2025
I was interviewed before Jan 2024.
Team work is best' work
based on 1 review
Rating in categories
Trainee
32
salaries
| ₹0 L/yr - ₹0 L/yr |
Diploma Mechanical Engineer
23
salaries
| ₹0 L/yr - ₹0 L/yr |
Production Engineer
21
salaries
| ₹0 L/yr - ₹0 L/yr |
CNC Operator
17
salaries
| ₹0 L/yr - ₹0 L/yr |
Diploma Trainee
17
salaries
| ₹0 L/yr - ₹0 L/yr |
Lakshmi Machine Works
Voltas
BHEL
TCS