i
JSW Steel
Filter interviews by
I applied via Campus Placement and was interviewed in Aug 2021. There were 3 interview rounds.
Top trending discussions
posted on 4 Jul 2023
I applied via Company Website and was interviewed in Nov 2022. There were 2 interview rounds.
CI casting refers to cast iron casting, which is made from a composition of iron, carbon, and silicon.
CI casting stands for cast iron casting.
It is made from a composition of iron, carbon, and silicon.
The carbon content in CI casting is typically between 2.1% and 4%.
The silicon content in CI casting is typically between 1% and 3%.
CI casting is known for its excellent castability, good machinability, and high wear resis
The pouring temperature of high chrome metal is typically between 1,600 to 1,800 degrees Celsius.
High chrome metal is commonly used in applications that require high temperature resistance and corrosion resistance.
The pouring temperature is crucial to ensure proper flow and solidification of the metal.
The specific pouring temperature may vary depending on the exact composition of the high chrome metal and the desired p...
I applied via Recruitment Consulltant and was interviewed in Jul 2024. There were 2 interview rounds.
Atmospheric pressure is the force per unit area exerted on a surface by the weight of the air above that surface.
Atmospheric pressure decreases with increasing altitude
Standard atmospheric pressure at sea level is around 1013.25 millibars or 29.92 inches of mercury
Atmospheric pressure is measured using barometers
Weight adjustment of a Load cell controller involves calibrating the controller to accurately measure weight.
Calibrate the load cell controller using known weights to ensure accurate measurements.
Adjust the zero balance to account for any offset in the readings.
Perform span adjustment to set the maximum weight range the controller can measure.
Verify the accuracy of the adjustments by testing with different weights.
Repe...
Calibrating AMLC on 15 plant involves ensuring accurate measurements and adjustments for optimal performance.
Ensure all 15 plants are properly set up and functioning correctly before calibration.
Use calibration equipment such as sensors, meters, and software to adjust AMLC settings.
Perform calibration tests on each plant individually to ensure accuracy and consistency.
Document calibration results and make necessary adj...
Qmap is used for quality mapping in software testing.
Qmap helps in identifying areas of improvement in software quality.
It provides a visual representation of quality metrics.
Qmap can be used to track defects and their resolution.
It helps in analyzing the effectiveness of testing strategies.
I was interviewed in Jul 2017.
I was interviewed in May 2019.
Steel sections are structural shapes made from steel for construction purposes.
I-beams
H-beams
C-channels
Angle sections
T-sections
Z-sections
Box sections
Circular sections
Different types of loads applied on long and short steel columns
Long columns are more susceptible to buckling under compressive loads
Short columns are more susceptible to crushing under compressive loads
Long columns are more likely to experience bending under lateral loads
Short columns are more likely to experience shear under lateral loads
Examples of loads include dead load, live load, wind load, seismic load, etc.
I was interviewed in Mar 2021.
I applied via Walk-in and was interviewed before Jun 2021. There were 2 interview rounds.
posted on 28 Jun 2022
I applied via Campus Placement and was interviewed before Jun 2021. There were 3 interview rounds.
Always start first and be crisp and interactive and stick to the topic
I applied via Walk-in and was interviewed in Nov 2023. There were 2 interview rounds.
Density of slurry is the mass of the slurry per unit volume.
Density of slurry is typically measured in kg/m^3 or lb/ft^3.
It is calculated by dividing the mass of the slurry by its volume.
The density of slurry can vary depending on the concentration of solids in the liquid.
For example, a slurry with a high concentration of solids will have a higher density.
SPL stands for Sound Pressure Level and SEL stands for Sound Exposure Level.
SPL is a measure of sound intensity relative to a reference level.
SEL is a measure of sound exposure over a period of time, typically in decibels.
Both SPL and SEL are commonly used in the field of acoustics and noise control.
The red area typically refers to a section or region that is highlighted or marked in the color red.
Red area can indicate danger or warning.
In engineering, red areas on diagrams or blueprints may signify areas of high risk or critical components.
Examples: red area on a map indicating a fire hazard zone, red area on a circuit diagram highlighting a high voltage section.
based on 2 interviews
Interview experience
Assistant Manager
3.1k
salaries
| ₹0 L/yr - ₹0 L/yr |
Junior Engineer
2.2k
salaries
| ₹0 L/yr - ₹0 L/yr |
Deputy Manager
1.7k
salaries
| ₹0 L/yr - ₹0 L/yr |
Manager
1.1k
salaries
| ₹0 L/yr - ₹0 L/yr |
Senior Engineer
991
salaries
| ₹0 L/yr - ₹0 L/yr |
Tata Steel
Steel Authority Of India
Vedanta Limited
ArcelorMittal Nippon Steel