AmbitionBox
Interview Questions
- Reviews
- Salaries
- Interview Questions
- About Company
- Benefits
- Jobs
- Office Photos
- Community
Add office photos
Filter interviews by
Gcc Services Rigging Supervisor Interview Questions and Answers
Gcc Services Rigging Supervisor Interview Experiences
1 interview found
Anonymous
(2 Questions)
- Q1. New movies in theaters I am not feeling good today
- Q2. What the company ruls
(2 Questions)
- Q1. Bags and you can come to you my 5
- Q2. New jabs person to be with her 5.30am person
Interview Preparation Tips
Interview questions from similar companies
I applied via Referral and was interviewed before Oct 2020. There were 4 interview rounds.
Interview Questionnaire
2 Questions
- Q1. All related to E&M
- Q2. What is power factor.
- Ans.
Power factor is the ratio of real power to apparent power in an AC circuit.
It is a measure of how efficiently electrical power is being used.
It ranges from 0 to 1, with 1 being the most efficient.
A low power factor can result in higher energy costs and equipment damage.
Capacitors can be used to improve power factor.
Example: A motor with a power factor of 0.8 requires 1.25 times more current than a motor with a power fa
Interview Preparation Tips
I applied via Referral and was interviewed in Feb 2021. There was 1 interview round.
Interview Questionnaire
3 Questions
- Q1. What is M-25 Grade concrete and what are its ratio
- Ans.
M-25 Grade concrete is a type of concrete with a compressive strength of 25 megapascals (MPa).
M-25 Grade concrete is commonly used in construction projects.
The ratio of M-25 Grade concrete is 1:1:2, which means 1 part cement, 1 part fine aggregate (sand), and 2 parts coarse aggregate (stone).
The mix proportion of M-25 Grade concrete is designed to achieve a desired strength and durability for the specific application.
F...
- Q2. How many bricks required in 1 cum.
- Ans.
The number of bricks required in 1 cubic meter depends on the size of the bricks and the thickness of the mortar joints.
The size of the bricks and the thickness of the mortar joints determine the number of bricks needed.
Standard brick sizes are commonly used in construction.
For example, if the size of the brick is 200mm x 100mm x 75mm and the thickness of the mortar joint is 10mm, the calculation would be as follows:
- ...
- Q3. 480 bricks required
Interview Preparation Tips
Selected
I applied via Walk-in and was interviewed before Sep 2023. There was 1 interview round.
(5 Questions)
- Q1. How many Experience your work
- Ans.
I have 5 years of experience working as a Site Supervisor in construction projects.
5 years of experience as a Site Supervisor
Managed multiple construction projects simultaneously
Ensured adherence to safety regulations and project timelines
Coordinated with subcontractors and communicated with clients
Implemented cost-saving measures without compromising quality
- Q2. You Interest Change your company
- Q3. Do you change your change
- Ans.
Yes, I am always open to change and adapt to new situations in order to improve efficiency and effectiveness.
I believe in continuous improvement and am willing to change my approach if it leads to better results
I am open to feedback and suggestions from team members and stakeholders
I have successfully implemented new processes and procedures in the past to enhance productivity
- Q4. Sarary Expectations
- Q5. Ok sir call again
Interview Preparation Tips
Selected
I applied via Walk-in and was interviewed in Nov 2024. There were 2 interview rounds.
What type of work termite tretment.
(5 Questions)
- Q1. New work and new site visit.
- Q2. What type work ?
- Q3. How to work termite treatment ?
- Ans.
For Pre Construction Anti Termite Treatment. The surface of the ground should be dry and clean. The chemical should be injected three times in a certain order into the ground. Firstly, the earth’s surface shall be drilled in 12mm diameter and 300mm deep at 150mm intervals below the PPC. Post construction. plinth area dril in home 45 degree angel 10" hole and gave 8/10" distance & wood area .
- Q4. How to control mosqutio ?
- Ans.
Spray continues inside the room. Drain area spray for anti larva treatment. Garden and out site for big fogger.
- Q5. How to control bedbugs etc...
- Ans.
Wash bedding, clothes, and blankets in hot water . and one chemical ( propoxure20%) best work for bed bugs and cockroach and household insecticide.
Interview Preparation Tips
Be prepared for anything.
Learn new school.
Act kindly to everyone.
Anytime active.
I applied via Naukri.com and was interviewed before Jun 2021. There were 3 interview rounds.
(1 Question)
- Q1. Questions related to the management part.
(1 Question)
- Q1. Some basic & Some intermediate questions in technical.
Interview Preparation Tips
I applied via Referral and was interviewed before Aug 2021. There were 2 interview rounds.
(1 Question)
- Q1. For xBis machines equipments and other parts related
Interview Preparation Tips
I applied via Referral and was interviewed before Aug 2021. There was 1 interview round.
(2 Questions)
- Q1. About switches, routers, servers and installation part and all in medium type
- Q2. English communication and local language Tamil must be for getting the job
Interview Preparation Tips
Selected
I appeared for an interview before Feb 2024.
(2 Questions)
- Q1. What is the role of (APFC)
- Ans.
The role of APFC (Automatic Power Factor Controller) is to maintain the power factor of electrical systems by automatically switching capacitors in and out of the circuit.
APFC monitors the power factor of the system and activates or deactivates capacitors accordingly.
It helps in reducing electricity bills by improving power factor and reducing reactive power consumption.
APFC ensures efficient utilization of electrical ...
- Q2. What is the Transformation Ratio?
- Ans.
Transformation ratio is the ratio of the number of turns in the primary winding to the number of turns in the secondary winding of a transformer.
Transformation ratio determines the voltage transformation between the primary and secondary windings of a transformer.
It is calculated as the ratio of the number of turns in the primary winding to the number of turns in the secondary winding.
For example, if a transformer has ...
Interview Preparation Tips
I applied via Referral and was interviewed before Nov 2020. There were 3 interview rounds.
Interview Questionnaire
1 Question
- Q1. About my experience in low voltage system.
Interview Preparation Tips
Gcc Services Interview FAQs
Tell us how to improve this page.
Interview Questions for Popular Designations
Gcc Services Rigging Supervisor Interview Process
based on 1 interview
Interview experience
Interview Questions from Similar Companies
|
Principal Analyst
28
salaries
|  ₹8.8 L/yr - ₹20.6 L/yr |
|
Senior Analyst
10
salaries
| ₹5.4 L/yr - ₹12.6 L/yr |
|
Analyst
7
salaries
| ₹5.2 L/yr - ₹11.1 L/yr |
|
Driver
5
salaries
| ₹2.5 L/yr - ₹5 L/yr |
|
Ptp Analyst
4
salaries
| ₹5.2 L/yr - ₹8.5 L/yr |
Sodexo
ISS Facility Services
BVG India
Leadec India
- Home >
- Interviews >
- Gcc Services Interview Questions >
- Gcc Services Rigging Supervisor Interview Questions
