AmbitionBox
Interview Questions
- Reviews
- Salaries
- Interview Questions
- About Company
- Benefits
- Jobs
- Office Photos
- Community
Add office photos
Filter interviews by
Energy Technical Services Hse and Safety Officer Interview Questions and Answers
Energy Technical Services Hse and Safety Officer Interview Experiences
1 interview found
I applied via Approached by Company and was interviewed before Jul 2021. There were 2 interview rounds.
(2 Questions)
- Q1. CV selection if shortlisted next Client interview and PTW exam mandatory.
- Q2. H2S Training, CSE Training, WAH Training mandatory.
Interview Preparation Tips
Interview questions from similar companies
Assistant Manager Interview Questions & Answers
NTPC GE Power Services
Anonymous
posted on 9 Oct 2024
Selected
I applied via Referral and was interviewed in Sep 2024. There was 1 interview round.
(7 Questions)
- Q1. What is main reason for belt joint failure?
- Ans.
The main reason for belt joint failure is usually due to improper installation or maintenance.
Improper installation of the belt joint, such as incorrect alignment or tensioning
Lack of proper maintenance, leading to wear and tear of the joint
Use of low-quality materials for the joint
Excessive load or stress on the belt joint
Environmental factors like temperature or humidity affecting the joint
- Q2. What was the alignment maximum tolerance?
- Ans.
The alignment maximum tolerance refers to the maximum allowable deviation from the specified alignment.
Alignment maximum tolerance is the maximum allowable deviation from the specified alignment.
It is typically expressed in terms of a percentage or a specific measurement unit.
For example, a machine part may have an alignment maximum tolerance of +/- 0.005 inches.
Exceeding the alignment maximum tolerance can lead to per
- Q3. How to replace the bucket wheel reclaimer luffing cylinder?
- Ans.
To replace the bucket wheel reclaimer luffing cylinder, follow these steps.
1. Shut down the machine and ensure all power sources are disconnected.
2. Remove any surrounding components that may obstruct access to the luffing cylinder.
3. Use appropriate tools to disconnect the hydraulic hoses and fittings from the cylinder.
4. Support the weight of the cylinder as it is removed to prevent damage to surrounding components.
5...
- Q4. What is different between JSA and HIRA?
- Ans.
JSA stands for Job Safety Analysis, focusing on specific job tasks, while HIRA stands for Hazard Identification and Risk Assessment, focusing on overall workplace hazards.
JSA is task-specific, focusing on individual job tasks and potential hazards
HIRA is broader, looking at overall workplace hazards and assessing risks
JSA involves breaking down a job into steps and identifying potential hazards for each step
HIRA involv...
- Q5. How create a PR in SAP?
- Ans.
To create a PR in SAP, you can use transaction code ME51N or ME21N.
Use transaction code ME51N to create a purchase requisition in SAP.
Enter the necessary details such as material, quantity, delivery date, etc.
Save the purchase requisition and it will be created in the system.
Alternatively, you can also use transaction code ME21N to create a purchase order directly.
- Q6. What is procedure of pulley replacement?
- Ans.
The procedure of pulley replacement involves identifying the faulty pulley, removing the old pulley, installing the new pulley, and testing the system.
Identify the faulty pulley by checking for any signs of wear or damage.
Use appropriate tools to remove the old pulley, such as a pulley puller or wrench.
Install the new pulley by aligning it properly and securing it in place.
Test the system to ensure the new pulley is fu...
- Q7. Explain the procedure of PTW?
- Ans.
PTW stands for Permit to Work, a procedure used to ensure that work is carried out safely in potentially hazardous environments.
PTW is a formal written system used to control certain types of work that are identified as potentially hazardous.
Before starting work, a permit must be obtained from a designated authority.
The permit outlines the work to be done, the hazards involved, and the necessary precautions to be taken...
Interview Preparation Tips
Skills evaluated in this interview
Assistant Manager Interview Questions & Answers
NTPC GE Power Services
Anonymous
posted on 4 Dec 2021
I applied via Company Website and was interviewed in Jun 2021. There were 3 interview rounds.
Interview Questionnaire
3 Questions
- Q1. How to find bearings details from bearing number.
- Ans.
To find bearing details from bearing number, refer to bearing catalogs or manufacturer's website.
Refer to bearing catalogs or manufacturer's website for detailed information
Search for the bearing number on the manufacturer's website to find specifications, dimensions, load ratings, and other details
Consult the bearing catalog to understand the type of bearing, its construction, and its applications
Contact the manufactu...
- Q2. How to coal yard management ?
- Ans.
Coal yard management involves efficient handling, storage, and transportation of coal.
Ensure proper storage and handling of coal to prevent contamination and loss
Implement safety measures to prevent accidents and injuries
Regularly inspect and maintain equipment to ensure smooth operations
Monitor coal inventory and plan for timely replenishment
Coordinate with suppliers and transporters for timely delivery of coal
Impleme...
- Q3. How to calculate SCC
- Ans.
SCC stands for Social Cost of Carbon and is calculated by estimating the economic damages caused by each ton of carbon dioxide emissions.
SCC is calculated by estimating the economic damages caused by each ton of carbon dioxide emissions
It takes into account the long-term effects of climate change on agriculture, health, property damage, and other factors
The SCC value is used to determine the cost-effectiveness of polic...
Interview Preparation Tips
Skills evaluated in this interview
Assistant Manager Interview Questions & Answers
NTPC GE Power Services
Anonymous
posted on 26 Jul 2024
(2 Questions)
- Q1. CT knee point testing
- Q2. Privious experience of Substation Maintenance and incedent
- Ans.
I have 5 years of experience in substation maintenance, including incident response and resolution.
Managed regular maintenance schedules for substation equipment
Responded to and resolved incidents such as power outages or equipment failures
Implemented safety protocols to prevent future incidents
Trained team members on proper maintenance procedures
Collaborated with engineers to improve substation efficiency
Assistant Manager Interview Questions & Answers
NTPC GE Power Services
Anonymous
posted on 1 Sep 2022
I applied via Company Website and was interviewed in Jul 2022. There were 3 interview rounds.
(2 Questions)
- Q1. About system,On critical situations what you do and handel
- Q2. How to manpower manage and utilise, Documentation what you do, Safety
- Ans.
Manpower management involves proper allocation and utilization of resources, documentation ensures accountability, and safety measures are crucial for a secure work environment.
Create a detailed manpower plan outlining roles, responsibilities, and tasks for each team member.
Regularly assess workload and adjust manpower allocation as needed to ensure efficiency.
Implement a documentation system to track progress, identif...
(1 Question)
- Q1. About salary , accommodation, other
Selected
I applied via Recruitment Consulltant and was interviewed in Jul 2022. There were 2 interview rounds.
(3 Questions)
- Q1. Asking about oisd and lpg basic
- Q2. Lpg ,oisd 144 and 169
- Q3. Salary discussion .Tamil is mandatory for this company
Interview Preparation Tips
Selected
I applied via Naukri.com and was interviewed before Aug 2022. There were 3 interview rounds.
(1 Question)
- Q1. Background of candidate
(1 Question)
- Q1. Technical & previous year experience
Interview Preparation Tips
Selected
I applied via Recruitment Consulltant and was interviewed before Oct 2022. There were 5 interview rounds.
(1 Question)
- Q1. A general HR questions
(1 Question)
- Q1. About last company and roles
2-3 Module of Aptitude and psychometric test
(1 Question)
- Q1. One on one with the VP/CEO
Shrikant Bhende
(2 Questions)
- Q1. Reason to switch the job?
- Ans.
Seeking new challenges and growth opportunities in a larger organization.
Looking for career advancement
Interested in taking on more responsibilities
Want to work in a larger team environment
Seeking better compensation and benefits
- Q2. What is your expectation?
- Ans.
My expectation is to contribute my skills and experience to help the team achieve its goals while continuing to grow and develop professionally.
I expect clear communication and direction from upper management.
I expect opportunities for growth and advancement within the company.
I expect a positive and collaborative work environment.
I expect to be given the necessary resources and support to succeed in my role.
Quantity Surveyor Interview Questions & Answers
Sterling Oil Exploration & Energy Production
Sulaiman Ogundare
posted on 20 May 2024
I applied via Referral and was interviewed in Apr 2024. There was 1 interview round.
(2 Questions)
- Q1. Experience about my past work as a Quantity Surveyor
- Q2. How will i handle subcontractor that's is applying for Contract
- Ans.
I will evaluate the subcontractor's qualifications, experience, and track record before considering them for the contract.
Review the subcontractor's past work and references
Assess the subcontractor's financial stability and capacity to complete the work
Negotiate terms and conditions of the contract to ensure clarity and alignment of expectations
Monitor the subcontractor's performance throughout the project to ensure qu...
Interview Preparation Tips
Energy Technical Services Interview FAQs
Tell us how to improve this page.
Interview Questions for Popular Designations
- Safety Officer Interview Questions
- Safety Supervisor Interview Questions
- Safety Engineer Interview Questions
- Safety Manager Interview Questions
- Drug Safety Associate Interview Questions
- Fire & Safety Officer Interview Questions
- Senior Safety Officer Interview Questions
- HSE Officer Interview Questions
- Show more
Interview Questions from Similar Companies
Energy Technical Services Hse and Safety Officer Reviews and Ratings
based on 1 review
Rating in categories
|
Safety Officer
12
salaries
|  ₹0 L/yr - ₹0 L/yr |
|
Mechanical Supervisor
10
salaries
| ₹0 L/yr - ₹0 L/yr |
|
Project Engineer
6
salaries
| ₹0 L/yr - ₹0 L/yr |
|
Electrical Engineer
5
salaries
| ₹0 L/yr - ₹0 L/yr |
|
Mechanical Technician
5
salaries
| ₹0 L/yr - ₹0 L/yr |
Petrofac
Schlumberger
Baker Hughes
NBTC GROUP
- Home >
- Interviews >
- Energy Technical Services Interview Questions >
- Energy Technical Services Hse and Safety Officer Interview Questions
