Filter interviews by
I appeared for an interview in Sep 2024, where I was asked the following questions.
Process knowledge & Drawing point.
Cp measures process capability, while Cpk measures process capability adjusted for centering.
Cp only considers the spread of data, while Cpk takes into account both spread and centering of data.
Cp assumes the process is centered within the specification limits, while Cpk adjusts for any deviation from the center.
If Cp is greater than Cpk, it indicates that the process is not centered within the specification limits.
For...
Quality statgy improvement study
Customer handling and management handling
I applied via Referral and was interviewed before Jun 2022. There were 3 interview rounds.
Use quality tools like Pareto chart, fishbone diagram, and 5 Whys to analyze and address customer complaints.
Identify the root cause of the complaint using tools like fishbone diagram.
Prioritize the issues using a Pareto chart to focus on the most critical problems first.
Use the 5 Whys technique to dig deeper into the root cause of the complaint.
Implement corrective actions based on the analysis to prevent similar comp
I applied via Approached by Company and was interviewed in May 2024. There was 1 interview round.
7QC tools are a set of quality control tools used for process improvement and problem-solving.
Check sheet: Used to collect and analyze data, such as tallying defects in a manufacturing process.
Pareto chart: Helps identify the most significant factors contributing to a problem, based on the 80/20 rule.
Cause and effect diagram (Fishbone diagram): Used to identify and analyze potential causes of a problem.
Histogram: Repre...
QA focuses on preventing defects in the process, while QC focuses on identifying defects in the product.
QA is process oriented, focusing on preventing defects by improving processes and procedures.
QC is product oriented, focusing on identifying defects through testing and inspection.
QA involves activities like reviews, audits, and process improvements.
QC involves activities like testing, inspections, and quality contro...
FMEA stands for Failure Modes and Effects Analysis, a systematic method for identifying and preventing potential failures in a system.
FMEA is a structured approach to identifying and prioritizing potential failure modes in a system.
It involves analyzing the potential effects of these failures and developing mitigation strategies.
FMEA helps in improving the reliability, safety, and quality of a system or process.
There a...
Process & product audit type of poka yoke ensures errors are prevented during audits.
Poka yoke in process audit involves using checklists to ensure all steps are followed correctly
Poka yoke in product audit involves using sensors to detect defects before they occur
Examples include using color-coded labels to prevent mix-ups in audits
I applied via Recruitment Consultant
QMS stands for Quality Management System and TPM stands for Total Productive Maintenance System.
QMS is a set of policies, processes, and procedures required for planning and execution of quality control.
TPM is a maintenance program that aims to maximize equipment effectiveness and minimize downtime.
QMS focuses on meeting customer requirements and improving customer satisfaction.
TPM focuses on improving equipment reliab...
I applied via Naukri.com and was interviewed in Jul 2023. There were 3 interview rounds.
The 7QC tools are a set of quality control tools used in process improvement. There are 7 tools in total.
The 7QC tools are: Pareto Chart, Cause and Effect Diagram, Check Sheet, Histogram, Scatter Diagram, Control Chart, and Flowchart.
These tools are used to identify, analyze, and solve quality-related problems in various processes.
Each tool serves a specific purpose, such as identifying the most significant issues (Par...
MSA stands for Measurement System Analysis. There are two types of MSA studies: Attribute Agreement Analysis and Variable Gauge R&R Study.
MSA is a method used to assess the measurement system's capability to provide accurate and reliable data.
Attribute Agreement Analysis is used when the measurement system classifies items into categories.
Variable Gauge R&R Study is used when the measurement system provides numerical m...
MSA study criteria refers to the guidelines and requirements for conducting a Measurement System Analysis.
MSA study criteria outline the steps and procedures for evaluating the measurement system used in a process.
It includes criteria for selecting appropriate measurement tools and techniques.
The criteria define the acceptable levels of accuracy, precision, linearity, and stability for the measurement system.
It also in...
based on 1 interview
Interview experience
based on 3 reviews
Rating in categories
Short Term Trainee
340
salaries
| ₹1.2 L/yr - ₹3 L/yr |
Trainee
280
salaries
| ₹1 L/yr - ₹3.5 L/yr |
Quality Engineer
236
salaries
| ₹1.2 L/yr - ₹4.5 L/yr |
Deputy Senior Engineer
229
salaries
| ₹3.1 L/yr - ₹7.2 L/yr |
Engineer
187
salaries
| ₹2.9 L/yr - ₹6.5 L/yr |
Motherson Automotive Technologies and Engineering
Belrise Industries
Krishna Maruti
Faurecia