i
Cummins
Proud winner of ABECA 2024 - AmbitionBox Employee Choice Awards
Filter interviews by
I applied via Naukri.com and was interviewed in Jul 2024. There were 2 interview rounds.
The weight of plates can be calculated by multiplying the density of the material by the volume of the plate.
Determine the density of the material the plate is made of (e.g. steel has a density of 7850 kg/m^3)
Measure the dimensions of the plate (length, width, thickness)
Calculate the volume of the plate using the formula: volume = length x width x thickness
Multiply the volume by the density to get the weight of the pla
There are various types of mechanical tools used in construction and maintenance work.
Hand tools (e.g. hammer, screwdriver, wrench)
Power tools (e.g. drill, saw, grinder)
Heavy equipment (e.g. excavator, bulldozer, crane)
Measuring tools (e.g. tape measure, level, calipers)
There are mainly three types of beams: Simply supported beam, Cantilever beam, and Overhanging beam.
Simply supported beam is supported at both ends and carries load in the middle.
Cantilever beam is supported at one end and carries load at the other end.
Overhanging beam has one or both ends extending beyond its supports.
There are several types of flanges used in piping systems for connecting pipes, valves, and other equipment.
Weld Neck Flange
Slip On Flange
Socket Weld Flange
Threaded Flange
Blind Flange
Lap Joint Flange
Orifice Flange
Top trending discussions
I was interviewed in Jul 2022.
I was interviewed in Jul 2022.
posted on 20 Dec 2021
I applied via Naukri.com and was interviewed in Nov 2021. There were 3 interview rounds.
The process of tower foundation involves several steps that are carried out day by day.
Day 1: Site preparation and layout survey
Day 2: Excavation for foundation
Day 3: Reinforcement placement
Day 4: Formwork installation
Day 5: Concrete pouring
Day 6: Curing of concrete
Day 7: Removal of formwork
Day 8: Quality inspection and testing
Day 9: Backfilling around the foundation
Day 10: Final inspection and documentation
Cube mould size refers to the dimensions of the mould used to cast concrete cubes for testing.
Cube moulds are typically made of steel or cast iron.
The most common cube mould size used in construction is 150mm x 150mm x 150mm.
Other sizes like 100mm x 100mm x 100mm or 200mm x 200mm x 200mm may also be used depending on the requirements.
Cube moulds have removable base plates to facilitate easy removal of the hardened conc...
Quality points at the pouring time of concrete include proper mix proportions, correct placement, adequate compaction, and appropriate curing.
Proper mix proportions ensure the desired strength and durability of the concrete.
Correct placement involves placing the concrete in the designated location without segregation or excessive bleeding.
Adequate compaction ensures that there are no voids or air pockets in the concret...
Sloped cutting refers to the excavation of soil or rock at an inclined angle to create a slope or incline.
Sloped cutting is commonly used in construction projects to create roadways, railways, or canals on hilly terrains.
It involves removing the excess material from a higher elevation to a lower elevation, forming a sloping surface.
The angle of the slope is determined based on factors such as soil stability, desired gr...
based on 1 interview
Interview experience
Junior Shop Manager
1.4k
salaries
| ₹2 L/yr - ₹10 L/yr |
Junior Manager
837
salaries
| ₹2.5 L/yr - ₹11 L/yr |
Diploma Trainee Engineer
521
salaries
| ₹1.1 L/yr - ₹2.8 L/yr |
Design Engineer
324
salaries
| ₹1.9 L/yr - ₹9 L/yr |
Executive Manager
219
salaries
| ₹11 L/yr - ₹33 L/yr |
BHEL
TCS
Larsen & Toubro Limited
Thermax Limited