Management Trainee - Technical

10+ Management Trainee - Technical Interview Questions and Answers for Freshers

Updated 10 Oct 2019
search-icon

Q1. 6. What is meant by hanging and slipping and how you tackle it?

Ans.

Hanging and slipping are two common issues in technical work. Learn how to tackle them effectively.

  • Hanging refers to a situation where a program or system stops responding or freezes.

  • Slipping refers to a situation where a program or system runs slower than expected.

  • To tackle hanging, try restarting the program or system, or checking for any updates or patches.

  • To tackle slipping, try optimizing the program or system, or upgrading hardware if necessary.

Q2. What are the different terms in the Navier Stokes equation?

Ans.

The Navier-Stokes equation describes the motion of fluid substances.

  • The Navier-Stokes equation is a set of partial differential equations that describe the motion of fluid substances.

  • It takes into account the conservation of mass, momentum, and energy.

  • The equation includes terms for pressure, viscosity, and acceleration.

  • It is used in many fields, including engineering, physics, and meteorology.

  • The equation is named after Claude-Louis Navier and George Gabriel Stokes, who inde...read more

Q3. 13. Iron and steel sector is in loss, why you want to opt it?

Ans.

Despite the current loss, I believe in the potential of the iron and steel sector to bounce back and contribute to the economy.

  • I am passionate about the technical aspects of the iron and steel sector

  • I have researched the current market trends and believe that with the right strategies, the sector can recover

  • I am excited about the opportunity to be a part of the solution and contribute to the growth of the sector

  • I am confident in my ability to learn and adapt to the challenges...read more

Q4. 14. what is your blending mixture of coal for Met coke making

Ans.

The blending mixture of coal for Met coke making depends on the quality of coal and the desired coke properties.

  • The blending mixture is determined by the quality of coal available.

  • The desired coke properties also play a role in determining the blending mixture.

  • The blending mixture typically includes a combination of coking coal, anthracite coal, and other additives.

  • The ratio of each component in the blending mixture can vary depending on the specific requirements.

  • For example,...read more

Are these interview questions helpful?

Q5. 4. Explain working of hot blast stoves and how to improve its efficiency

Ans.

Hot blast stoves preheat air before it enters the blast furnace. Efficiency can be improved by using waste heat recovery systems.

  • Hot blast stoves preheat air to around 1200°C before it enters the blast furnace

  • Efficiency can be improved by using waste heat recovery systems to recover heat from the stove exhaust gases

  • Insulating the stove walls and using high-quality refractory materials can also improve efficiency

  • Regular maintenance and cleaning of the stove can prevent heat lo...read more

Q6. The difference between distillation column and absorption column. What factor decides the feasibility to use distillation column to separate two components?

Ans.

Distillation column separates components based on boiling points while absorption column separates based on solubility.

  • Distillation column separates components based on their boiling points while absorption column separates based on their solubility in a particular solvent.

  • Distillation column is used when the boiling points of the components to be separated are significantly different.

  • Absorption column is used when the components to be separated have similar boiling points bu...read more

Share interview questions and help millions of jobseekers 🌟

man-with-laptop

Q7. 12. what do you do your blast furnace slag? you sell at what cost?

Ans.

We sell blast furnace slag as a byproduct to construction companies at market rates.

  • Blast furnace slag is a byproduct of the steel-making process.

  • We sell it to construction companies for use in cement and concrete production.

  • The cost varies depending on market rates and demand.

  • We ensure that the slag meets all necessary quality standards before selling it.

  • We also explore potential new markets for the slag to maximize its value.

Q8. 11. If we give you the chance, how are you going to increase the efficiency of hot blast stoves.

Ans.

Efficiency of hot blast stoves can be increased by optimizing combustion, improving insulation, and reducing heat losses.

  • Optimize combustion by using high-quality fuel and maintaining proper air-to-fuel ratio

  • Improve insulation by using high-temperature refractory materials and insulating the stove walls

  • Reduce heat losses by minimizing air leaks and using heat recovery systems

  • Regular maintenance and cleaning of the stoves can also improve efficiency

  • Implementing advanced contro...read more

Q9. 7. When furnace is getting chilled, what steps you take

Ans.

Steps to take when furnace is getting chilled

  • Check the fuel supply and adjust if necessary

  • Inspect the burners and clean them if needed

  • Check the thermostat and adjust the temperature settings

  • Inspect the air filters and replace if dirty

  • Check the insulation and repair any leaks

  • Inspect the ductwork and repair any leaks

  • Check the blower motor and lubricate if needed

Q10. How do you derive the continuity equation?

Ans.

Deriving the continuity equation

  • Continuity equation states that mass cannot be created or destroyed, only conserved

  • It relates the mass flow rate, density, and velocity of a fluid

  • The equation is derived from the principle of conservation of mass

  • The equation can be applied to both steady and unsteady flow

  • The continuity equation is important in fluid dynamics and engineering

Q11. Write down the continuity equation for a compressible flow?

Ans.

Continuity equation for compressible flow

  • The continuity equation states that mass cannot be created or destroyed in a flow system

  • For compressible flow, the equation takes into account changes in density due to changes in pressure and temperature

  • The equation is expressed as: ∂(ρ)/∂t + ∇(ρv) = 0

  • ρ is the density, t is time, v is velocity, and ∇ is the divergence operator

  • The equation can be used to analyze fluid flow in a variety of applications, such as aerodynamics and gas dyna...read more

Q12. Heat transfer rate through walls of different conductivity and of the same area of heat transfer and length

Ans.

Heat transfer rate through walls of different conductivity and of the same area of heat transfer and length

  • Heat transfer rate is directly proportional to the thermal conductivity of the material

  • Thermal conductivity is the ability of a material to conduct heat

  • Materials with high thermal conductivity transfer heat faster than those with low thermal conductivity

  • Heat transfer rate can be calculated using Fourier's law of heat conduction

  • Example: Copper has a higher thermal conduct...read more

Q13. Explain swinging of the cricket ball?

Ans.

Swinging of the cricket ball is the movement of the ball in the air due to the aerodynamic properties of the ball.

  • Swinging occurs due to the difference in air pressure on either side of the ball.

  • The side of the ball that is rougher creates turbulence in the air, causing the ball to swing towards that side.

  • Bowlers use various techniques such as shining one side of the ball or applying saliva to create differential roughness.

  • Swinging can be both inwards (towards the batsman) or...read more

Q14. What is a PID controller?

Ans.

A PID controller is a feedback control loop that calculates an error value as the difference between a desired setpoint and a measured process variable.

  • PID stands for Proportional-Integral-Derivative

  • It is commonly used in industrial control systems to regulate temperature, pressure, flow, and other process variables

  • The proportional term responds to the current error value, the integral term responds to the accumulated error over time, and the derivative term responds to the r...read more

Q15. Would you prefer ITC over BCG?

Ans.

It depends on personal preferences and career goals.

  • Consider the company culture and values

  • Evaluate the job responsibilities and growth opportunities

  • Research the industry and market trends

  • Assess the compensation and benefits package

  • Seek advice from current or former employees

  • Example: If you value work-life balance, ITC may be a better fit as they offer flexible work arrangements. However, if you prioritize prestige and challenging projects, BCG may be more suitable.

  • Example: I...read more

Interview Tips & Stories
Ace your next interview with expert advice and inspiring stories

Interview experiences of popular companies

4.1
 • 858 Interviews
3.9
 • 546 Interviews
4.1
 • 342 Interviews
4.0
 • 172 Interviews
3.7
 • 126 Interviews
4.0
 • 48 Interviews
4.1
 • 28 Interviews
View all

Calculate your in-hand salary

Confused about how your in-hand salary is calculated? Enter your annual salary (CTC) and get your in-hand salary

Management Trainee - Technical Interview Questions
Share an Interview
Stay ahead in your career. Get AmbitionBox app
qr-code
Helping over 1 Crore job seekers every month in choosing their right fit company
65 L+

Reviews

4 L+

Interviews

4 Cr+

Salaries

1 Cr+

Users/Month

Contribute to help millions

Made with ❤️ in India. Trademarks belong to their respective owners. All rights reserved © 2024 Info Edge (India) Ltd.

Follow us
  • Youtube
  • Instagram
  • LinkedIn
  • Facebook
  • Twitter