Filter interviews by
I appeared for an interview in Feb 2023.
Fade system is a method used in injection molding to gradually reduce the pressure and speed of the injection process. Core and cavity are the two halves of a mold used in injection molding. To plate mold is a type of mold where a metal plate is used to create the mold cavity. Pitch diameter of a bolt is the diameter of an imaginary cylinder that passes through the threads of the bolt.
Fade system is used in injection m...
A single cavity mould is a type of mould that only produces one part per cycle.
Single cavity moulds are used for low volume production.
They are simpler and cheaper compared to multi-cavity moulds.
Examples include prototype moulds and custom moulds for unique parts.
Jigs are used to guide cutting tools and fixtures hold the workpiece in place during machining operations.
Jigs are used to guide cutting tools, while fixtures hold the workpiece in place
Jigs are used for drilling, reaming, and tapping operations, while fixtures are used for milling, grinding, and turning operations
Jigs are more complex and expensive than fixtures
Jigs are often used for mass production, while fixtures a
The nominal diameter of a bolt refers to the size of the bolt shaft, excluding the threads.
Nominal diameter is the diameter of the bolt shaft, not including the threads
It is typically measured in millimeters or inches
For example, a bolt with a nominal diameter of 10mm has a shaft diameter of 10mm
Top trending discussions
I applied via Walk-in and was interviewed in Feb 2020. There were 4 interview rounds.
The unit of pressure is Pascal (Pa).
Pressure is defined as force per unit area.
The SI unit of force is Newton (N) and the SI unit of area is square meter (m²).
Therefore, the SI unit of pressure is Newton per square meter (N/m²) or Pascal (Pa).
Other common units of pressure include pounds per square inch (psi) and atmospheres (atm).
I applied via Recruitment Consultant and was interviewed in Jun 2019. There were 3 interview rounds.
I worked as a Junior Engineer at XYZ Company for 2 years, where I gained experience in project management and technical troubleshooting.
Managed multiple projects simultaneously
Collaborated with cross-functional teams to achieve project goals
Resolved technical issues on the production line
Implemented process improvements to increase efficiency
I applied via Naukri.com and was interviewed in Dec 2020. There were 3 interview rounds.
posted on 5 Jul 2021
posted on 1 Jun 2020
I applied via Naukri.com and was interviewed in May 2020. There were 4 interview rounds.
Die casting and machining defects are common in manufacturing processes.
Die casting defects include porosity, shrinkage, cold shuts, and flash.
Machining defects include burrs, chatter marks, and tool marks.
Die casting defects can be caused by improper temperature, pressure, or metal flow.
Machining defects can be caused by dull tools, improper speeds and feeds, or poor fixturing.
Defects can lead to part failure, reduced
Filling and high speed ratio formula is used to calculate the filling time of a container with a specific volume of liquid at a given flow rate.
Filling and high speed ratio formula is V/Q
V is the volume of the container and Q is the flow rate of the liquid
The formula is used to determine the time it takes to fill a container with a specific volume of liquid at a given flow rate
The higher the flow rate, the faster the c
posted on 26 Nov 2021
An op-amp is a type of electronic amplifier with high gain and differential inputs.
Op-amp stands for operational amplifier.
It is a key component in analog circuits and is widely used in signal processing and amplification.
Op-amps have two inputs, an inverting and a non-inverting input, and a single output.
They are typically used to amplify and manipulate signals, perform mathematical operations, and control circuit beh...
posted on 26 Nov 2021
I applied via Campus Placement and was interviewed in May 2021. There was 1 interview round.
Operational Amplifier (Op-Amp) is a popular Linear Integrated Circuit.
Op-Amp is used in various applications such as amplifiers, filters, oscillators, comparators, etc.
Some popular Op-Amps are LM741, LM358, LM324, etc.
Op-Amps have high input impedance, low output impedance, and high gain.
Op-Amps can be used in both inverting and non-inverting configurations.
Five instruments of linear integrated circuit
Operational Amplifier (Op-Amp)
Voltage Regulator
Comparator
Timer
Phase Locked Loop (PLL)
posted on 8 Jan 2022
Quality refers to the degree of excellence or superiority of a product or service.
Quality is the measure of how well a product or service meets the expectations and requirements of customers.
It involves meeting or exceeding standards and specifications.
Quality can be subjective and may vary based on individual preferences and needs.
Quality can be assessed through various methods such as inspections, testing, and custom...
posted on 25 Nov 2023
based on 1 interview
Interview experience
based on 3 reviews
Rating in categories
Design Engineer
39
salaries
| ₹3.5 L/yr - ₹11.3 L/yr |
Team Lead
34
salaries
| ₹2.3 L/yr - ₹8.2 L/yr |
CAE Analyst
19
salaries
| ₹3.6 L/yr - ₹9.5 L/yr |
Assistant Manager
16
salaries
| ₹6.7 L/yr - ₹17 L/yr |
Senior Engineer
16
salaries
| ₹8.2 L/yr - ₹13 L/yr |
Bosch
Samvardhana Motherson Group
Yazaki
Delphi TVS