Toyota Kirloskar Motor Assembly Technician Interview Questions and Answers

Equipment related question

Q1. How to use measurement equipment
Ans. 
To use measurement equipment, follow these steps: calibrate the equipment, select the appropriate measurement tool, take accurate measurements, record the data, and maintain the equipment.
• Calibrate the measurement equipment regularly to ensure accuracy.

• Select the appropriate measurement tool for the specific task or measurement needed.

• Take accurate measurements by following the instructions provided with the equipment.

• ...read more
Answered by AI
Add your answer

Q1. Line engineering
Add your answer
Q2. Menpawar Hendaling
Add your answer

Q1. New model Development
Add your answer
Q2. Special tools trial
Add your answer

Q1. Vender management
Add your answer
Q2. Dispatch planing
Add your answer

Engine assemble ,cap contact

Q1. How goes gears work?
Ans. 
Gears work by transferring motion and power between two rotating shafts through interlocking teeth.
• Gears have teeth that mesh together to transmit motion and power

• Different gear sizes can change the speed and torque of the output shaft

• Common types of gears include spur gears, helical gears, and bevel gears
Answered by AI
Add your answer
Q2. Type of gears and it's uses?
Ans. 
Types of gears include spur gears, helical gears, bevel gears, and worm gears, each with specific uses in various mechanical systems.
• Spur gears: used in applications requiring high speed and low noise, such as in washing machines

• Helical gears: provide smoother operation and higher load capacity, commonly found in automotive transmissions

• Bevel gears: used to transmit motion between intersecting shafts, like in hand dril...read more
Answered by AI
Add your answer
Q3. What's is primary axis of circle.
Ans. 
The primary axis of a circle is the line passing through the center of the circle and dividing it into two equal halves.
• The primary axis of a circle is also known as the diameter.

• It is the longest chord that can be drawn in a circle.

• The length of the primary axis is twice the radius of the circle.

• The primary axis is a line of symmetry for the circle.
Answered by AI
Add your answer
Q4. Type of gear meshing.
Ans. 
Gear meshing can be classified as spur, helical, bevel, worm, etc.
• Spur gears have straight teeth and are used for parallel shafts

• Helical gears have angled teeth for smoother operation

• Bevel gears are used for intersecting shafts

• Worm gears have a screw-like appearance for high torque applications
Answered by AI
Add your answer

Q1. What is Electronic component function details?
Ans. 
Electronic components are devices that perform specific functions within an electronic circuit.
• Electronic components are used to control the flow of electric current or to amplify signals.

• They can be passive components like resistors, capacitors, and inductors, or active components like transistors and integrated circuits.

• Each component has a specific function, such as storing energy, filtering signals, or converting o...read more
Answered by AI
View 1 more answer
Q2. Diodes function= ac to dc rectify
Ans. 
Diodes function as rectifiers, converting alternating current (AC) to direct current (DC).
• Diodes allow current to flow in one direction while blocking it in the opposite direction.

• They have a forward voltage drop that causes the AC waveform to be rectified into a pulsating DC waveform.

• The rectified output can be further smoothed using capacitors and filters.

• Examples of diodes used for rectification include the 1N4001 a...read more
Answered by AI
Add your answer
Q3. What is voltage= a flow of electron.
Ans. 
Voltage is the potential difference between two points in an electrical circuit that drives the flow of electrons.
• Voltage is measured in volts (V).

• It represents the amount of energy carried by each unit of charge.

• Voltage can be compared to the pressure in a water pipe, where higher voltage means more potential energy for electrons to flow.

• Voltage is essential for the operation of electronic devices and electrical syste...read more
Answered by AI
Add your answer
Q4. What is Transistor= transistor three pin components.pin nams Base, emitor, collector.
Ans. 
A transistor is a three-pin electronic component with pins named Base, Emitter, and Collector.
• Transistors are used to amplify or switch electronic signals.

• The Base pin controls the flow of current between the Emitter and Collector pins.

• The Emitter is the source of electrons, while the Collector collects them.

• Transistors are commonly used in electronic devices such as computers, televisions, and radios.
Answered by AI
Add your answer
Q5. What is ammeter= wolt measuring.
Ans. 
An ammeter measures electric current in a circuit.
• Ammeters are used to measure the flow of electric current in a circuit.

• They are connected in series with the circuit to measure the current passing through it.

• The unit of measurement for current is amperes (A).

• Ammeters have low resistance to avoid altering the circuit's current.

• For example, an ammeter can be used to measure the current flowing through a light bulb.
Answered by AI
Add your answer

Department over all questions

Q1. Assembly operators relationship questions
Add your answer

Q1. Mechanical department questions and general knowledge questions
Add your answer

Q1. About vehicle or technical
Add your answer
Q2. Some technical questions
Add your answer
Q3. About my qualifications
Add your answer

Q1. What is your opinion about engine?
Ans. 
An engine is a complex mechanical device that converts energy into mechanical motion.
• Engines are used in various applications such as automobiles, aircraft, and power plants.

• They can be powered by different sources such as gasoline, diesel, or electricity.

• Engines consist of multiple components such as cylinders, pistons, valves, and crankshafts.

• Efficiency and performance are important factors in engine design and devel...read more
Answered by AI
View 2 more answers
Q2. How to increase stroke length without changing in bore dia?
Ans. 
To increase stroke length without changing bore diameter, one can modify the crankshaft design or adjust the connecting rod length.
• Modify the crankshaft design to increase the throw radius, which will result in a longer stroke length.

• Adjust the connecting rod length to change the stroke ratio, allowing for a longer stroke without changing the bore diameter.

• Consider the trade-offs and limitations of increasing stroke le...read more
Answered by AI
View 1 more answer