AmbitionBox
Interview Questions
- Reviews
- Salaries
- Interview Questions
- About Company
- Benefits
- Jobs
- Office Photos
- Community
Add office photos
Filter interviews by
SSF PLASTICS Shift Incharge Interview Questions and Answers
SSF PLASTICS Shift Incharge Interview Experiences
1 interview found
Anonymous
I applied via Recruitment Consulltant and was interviewed before Aug 2021. There were 3 interview rounds.
(2 Questions)
- Q1. Production department from any questions
- Q2. Production department from any questions
(1 Question)
- Q1. Production department asked any questions
Interview Preparation Tips
Interview questions from similar companies
Selected
I appeared for an interview before Mar 2024, where I was asked the following questions.
- Q1. Learning from past companies.
- Q2. 5 core tools of Quality.
- Q3. IATF clauses for NPD.
Interview Preparation Tips
Selected
(2 Questions)
- Q1. What is carbon black
- Ans.
Carbon black is a fine powder made from incomplete combustion of hydrocarbons.
It is used as a reinforcing filler in rubber products.
It is also used as a black pigment in inks, paints, and plastics.
Carbon black is produced by burning petroleum oil or natural gas.
It is a common ingredient in tires, conveyor belts, and other industrial rubber products.
- Q2. What is Air preheater
- Ans.
Air preheater is a device used to heat the air before it enters the combustion chamber of a boiler.
It improves the efficiency of the boiler by recovering waste heat from the flue gas.
It reduces fuel consumption and emissions.
There are two types of air preheaters: recuperative and regenerative.
Recuperative air preheaters use a heat exchanger to transfer heat from the flue gas to the incoming air.
Regenerative air preheat...
Interview Questionnaire
1 Question
- Q1. Introduction, job portfolio handled, over all experience n job knowledge, profile suitability
I applied via Referral and was interviewed in May 2019. There were 3 interview rounds.
Interview Questionnaire
3 Questions
- Q1. What is dsr
- Ans.
DSR stands for Daily Sales Report. It is a document that summarizes the sales activities and performance of a business on a daily basis.
DSR provides insights into daily sales trends and helps in tracking sales targets.
It includes information such as total sales, number of transactions, average transaction value, and sales by product or category.
DSR is used by managers to evaluate sales performance, identify areas for i...
- Q2. How did you check the stock and volume
- Ans.
I used a combination of inventory management software, physical counts, and sales reports to check stock and volume.
Utilized inventory management software to track stock levels and monitor volume
Conducted regular physical counts to ensure accuracy of stock levels
Analyzed sales reports to identify trends and forecast future stock and volume needs
- Q3. What are the calculations in petrol pump
- Ans.
Calculations in petrol pump involve measuring fuel quantity, calculating cost, and maintaining inventory.
Fuel quantity is measured using a flow meter or dipstick.
Cost is calculated based on the price per liter or gallon.
Inventory is maintained by tracking fuel deliveries and sales.
Calculations may also involve taxes, discounts, and loyalty programs.
Accuracy is crucial to prevent losses and ensure customer satisfaction.
Interview Preparation Tips
Skills evaluated in this interview
Selected
I applied via Company Website and was interviewed before Feb 2022. There were 2 interview rounds.
(2 Questions)
- Q1. What is cavitation in centrifugal pump? How do you mean by NPSH?
- Ans.
Cavitation is the formation of vapor bubbles in a centrifugal pump due to low pressure. NPSH stands for Net Positive Suction Head.
Cavitation occurs when the pressure at the pump inlet drops below the vapor pressure of the liquid, causing the formation of vapor bubbles.
These vapor bubbles collapse when they reach higher pressure areas, leading to damage to the pump impeller and reduced pump performance.
Cavitation can be...
- Q2. What is surging? How do you manage lubrication in different rotating equipment?
- Ans.
Surging is a phenomenon in rotating equipment where the flow rate becomes unstable.
Surging occurs when the flow rate through a rotating equipment fluctuates due to changes in operating conditions.
It can lead to reduced efficiency, increased wear and tear, and potential damage to the equipment.
To manage lubrication in different rotating equipment, it is important to monitor and control the flow rate, viscosity, and temp...
Interview Preparation Tips
About job profile, key interest on jobs, new challenges
I applied via Company Website and was interviewed in Nov 2022. There were 2 interview rounds.
(2 Questions)
- Q1. They ask about your questions on the ongoing experience.
- Q2. Knowledge about Process safety
Interview Preparation Tips
- Process Safety
(1 Question)
- Q1. Why you come in HPL?
(2 Questions)
- Q1. Plant tank farm and utility
- Q2. Tell about PSA cycle
Interview Preparation Tips
If you are fresher then only it is a good company.
Proper manpower allocation is very poor
Selected
I applied via Recruitment Consulltant and was interviewed before Apr 2023. There were 3 interview rounds.
(1 Question)
- Q1. Unnecessarily questions asked by interviewer
(1 Question)
- Q1. Nothing has been asked. Only they have done promises which they didn't fulfill after joining
(1 Question)
- Q1. It was good , and HR is very polite
Interview Preparation Tips
SSF PLASTICS Interview FAQs
Tell us how to improve this page.
SSF PLASTICS Interviews By Designations
- SSF PLASTICS Account Assistant Interview Questions
- SSF PLASTICS Production Manager Interview Questions
- SSF PLASTICS QA QC Engineer Interview Questions
- SSF PLASTICS Factory Head Interview Questions
- SSF PLASTICS Senior Electrical Technician Interview Questions
- SSF PLASTICS Junior Engineer Interview Questions
- SSF PLASTICS Junior Officer - QA Interview Questions
- SSF PLASTICS Store Supervisor Interview Questions
- Show more
Interview Questions for Popular Designations
- Shift Engineer Interview Questions
- Production Shift Incharge Interview Questions
- Shift Supervisor Interview Questions
- Shift Incharge Engineer Interview Questions
- Electrical Shift Engineer Interview Questions
- Electrical Shift Incharge Interview Questions
- Shift Manager Interview Questions
- Shift Officer Interview Questions
- Show more
SSF PLASTICS Shift Incharge Interview Process
based on 1 interview
Interview experience
Interview Questions from Similar Companies
SSF PLASTICS Shift Incharge Reviews and Ratings
based on 5 reviews
Rating in categories
|
Production Engineer
66
salaries
|  ₹1.8 L/yr - ₹5.5 L/yr |
|
Junior Engineer
51
salaries
| ₹1.8 L/yr - ₹4.1 L/yr |
|
Quality Engineer
36
salaries
| ₹1.7 L/yr - ₹4.2 L/yr |
|
Quality Officer
28
salaries
| ₹2 L/yr - ₹3.6 L/yr |
|
Engineer
24
salaries
| ₹3 L/yr - ₹6.2 L/yr |
Nayara Energy
HPCL-Mittal Energy Limited
Ongc Petro Additions
Sintex-bapl
- Home >
- Interviews >
- SSF PLASTICS Interview Questions >
- SSF PLASTICS Shift Incharge Interview Questions
