20+ Kent plc Interview Questions and Answers

Preventive and corrective maintenance of various electrical equipment including breakers, motors, transformers, switches, relays, and testing/calibration of protections.

• Preventive maintenance of H.V & LV breakers, motors, transformers, switches, etc.

• Corrective maintenance of HV/MV/LV switchgears, breakers, cubicles, etc.

• Testing and calibration of various protection relays for motors, transformers, generators.

• Transformer oil BDV test, thermal scanning, earth fault and predicti...read more

Answering questions related to confined space job, alignment of pump and motor, types of gaskets and valves, and troubleshooting reciprocating compressor.

• Safety watch is responsible for monitoring the workers inside the confined space and ensuring their safety.

• Alignment of pump and motor can be done using dial indicators or laser alignment tools.

• Different types of gaskets include spiral wound, ring joint, and sheet gaskets. Different types of valves include gate, globe, ball,...read more

The status of the bus tie when the 2 incomers are energized depends on the specific electrical system design.

• In some electrical systems, the bus tie remains open when both incomers are energized.

• In other systems, the bus tie automatically closes to parallel the two incomers.

• The purpose of the bus tie is to provide redundancy and flexibility in the electrical system.

• Examples of bus tie statuses include 'open', 'closed', 'auto', or 'sync'.

To restore a broken fiber, I would first locate the break and then splice the fiber back together.

• Locate the break in the fiber

• Clean and prepare the fiber ends for splicing

• Splice the fiber back together using fusion splicing or mechanical splicing

• Test the restored fiber to ensure it is functioning properly

Stall in a motor refers to a condition where the motor stops rotating despite the presence of power supply.

• Stall occurs when the motor is overloaded or when there is a mechanical obstruction preventing the motor from rotating.

• It can also occur when the motor is underpowered or when there is a fault in the electrical system.

• Stall can cause damage to the motor and other components if not addressed promptly.

• Examples of motors that can experience stall include AC motors, DC motor...read more

The answer depends on the context of the situation.

• In electrical wiring, the black wire is usually IN and the white wire is OUT.

• In plumbing, the water flows IN from the main supply and OUT through the drain.

• In HVAC systems, the air flows IN through the return duct and OUT through the supply duct.

• In manufacturing, the IN side is usually where the raw materials are loaded and the OUT side is where the finished product is unloaded.

External internal panel wiring connection refers to the wiring connections made between the external devices and the internal components of an electrical panel.

• External internal panel wiring connection involves connecting external devices such as sensors, switches, and actuators to the internal components of an electrical panel.

• These connections are made using wires or cables and are essential for the proper functioning of the electrical panel.

• The external devices are typical...read more

There are various types of enclosures used in different industries for different purposes.

• Types of enclosures include electrical enclosures, outdoor enclosures, server enclosures, and soundproof enclosures.

• Electrical enclosures protect electrical equipment from environmental factors such as dust, water, and chemicals.

• Outdoor enclosures protect equipment from weather conditions such as rain, snow, and extreme temperatures.

• Server enclosures are used to house servers and other I...read more

UPS stands for Uninterruptible Power Supply. It is an electrical device that provides emergency power to a load when the input power source fails.

• UPS has three main components: battery, inverter, and rectifier.

• The battery provides backup power during a power outage.

• The rectifier converts AC power to DC power to charge the battery.

• The inverter converts DC power from the battery to AC power to supply the load.

• UPS also has a transfer switch that switches the load to the battery ...read more

Yes, I can draw the diagram to show you.

• I can draw the diagram on paper or using a software like AutoCAD.

• I will need to know the specific details of the diagram you want me to draw.

• I can also explain the different components and their functions in the diagram.

Various standards used in the Oil & Gas Industry include API, ASME, ISO, and NACE.

• API (American Petroleum Institute) standards cover various aspects of the industry such as drilling, production, and transportation.

• ASME (American Society of Mechanical Engineers) standards focus on equipment design and safety.

• ISO (International Organization for Standardization) standards ensure quality and consistency in processes and products.

• NACE (National Association of Corrosion Engineers) ...read more

Interfaces in engineering projects refer to the points where different components or systems connect and interact with each other.

• Interfaces between different engineering disciplines (e.g. mechanical, electrical, software)

• Interfaces between different project stakeholders (e.g. clients, contractors, suppliers)

• Interfaces between different project phases (e.g. design, procurement, construction)

• Interfaces between different project teams or departments within an organization

• Exampl...read more

Yes, I have experience in splicing work.

• I have spliced fiber optic cables for a telecommunications company.

• I have also spliced electrical wires for a construction project.

• I am familiar with the tools and techniques required for splicing work.

The Safety policy is approved and signed by top management.

• Safety policy is approved and signed by top management or senior leadership.

• Typically, the CEO, Managing Director, or equivalent high-ranking official signs the Safety policy.

• The Safety Officer may be responsible for drafting the policy and ensuring it aligns with regulations and best practices.

Fabrication as per ISO drawing involves following the dimensions, tolerances, and specifications provided in the drawing.

• Carefully study the ISO drawing to understand the dimensions and specifications required for fabrication.

• Use appropriate tools and equipment to cut, shape, and assemble the materials according to the drawing.

• Ensure that the final product meets the tolerances and quality standards specified in the ISO drawing.

• Regularly check and compare the work in progress ...read more

I solve problems by analyzing the root cause, developing a plan of action, and implementing solutions effectively.

• Identify the problem and gather relevant information

• Analyze the root cause of the issue

• Develop a plan of action to address the problem

• Implement solutions effectively

• Monitor and evaluate the effectiveness of the solutions

Everyone in the workplace is responsible for safety, from management to employees.

• Management is responsible for providing a safe work environment and enforcing safety policies.

• Employees are responsible for following safety procedures and reporting any hazards or incidents.

• Safety officers are responsible for conducting safety inspections, training employees, and ensuring compliance with regulations.

CS and SS pipe codes refer to the material specifications for carbon steel and stainless steel pipes used in piping systems.

• CS pipe code typically refers to ASTM A106 for seamless carbon steel pipes or ASTM A53 for welded carbon steel pipes.

• SS pipe code typically refers to ASTM A312 for seamless stainless steel pipes or ASTM A358 for welded stainless steel pipes.

• CS pipes are commonly used in industrial applications, while SS pipes are preferred for corrosive environments.

• CS p...read more