Upload Button Icon Add office photos

Jindal Stainless

Compare button icon Compare button icon Compare

Filter interviews by

Jindal Stainless Electronics Engineer Interview Questions and Answers

Updated 1 Dec 2024

Jindal Stainless Electronics Engineer Interview Experiences

1 interview found

Interview experience
5
Excellent
Difficulty level
-
Process Duration
-
Result
Selected Selected
Round 1 - HR 

(1 Question)

  • Q1. Electrical engineering maintainace project

Interview questions from similar companies

I appeared for an interview in Jul 2017.

Interview Preparation Tips

Round: Test
Experience: all job related technical question
Duration: 35 minutes
Total Questions: 30

Skills: Interest In The Job, Body Language In Interview

I appeared for an interview before Jul 2016.

Interview Questionnaire 

1 Question

  • Q1. Introduction, company profile,hobby,about your work

Interview Preparation Tips

Round: Resume Shortlist
Experience: after shortlisted of resume call from jindal group

Round: Group Activity
Experience: fulfill form and enjoy.

Round: Test
Experience: passed in exam.
Duration: 30 minutes
Total Questions: 80

Round: Technical + HR Interview
Experience: I'm faces all questions and confidentially answerd

Interview Questionnaire 

1 Question

  • Q1. 1- Your Experience 2- Favourite Subject Like in my case i said Fluid Mechanics, so he asked questions on the subject. Types of pumps, NPSH, Bernoullis theorem, barometric head, types of fluid, Cavitation...

Interview Preparation Tips

Round: Test
Experience: When you will go through the JSPL website it will say the following things asked in the test
Aptitude
Reasoning
Technical 40ques 18min.
Psychometric test
But aptitude was not asked only verbal Reasoning.
So basically
80 questions and 60 minutes.

Round: Group Discussion
Experience: Digital India and
Ecological development over Economic development.

Interview Questionnaire 

6 Questions

  • Q1. 1.what is composite error and ratio error in current transformer?
  • Ans. 

    Composite error and ratio error are two types of errors in current transformers.

    • Composite error is the combination of ratio error and phase angle error in a current transformer.

    • Ratio error is the difference between the actual turns ratio and the specified turns ratio of a current transformer.

    • Phase angle error is the angular difference between the primary and secondary currents of a current transformer.

    • Composite error a...

  • Answered by AI
  • Q2. 2.Draw ckt diagram of a.c drive.
  • Ans. 

    An AC drive circuit diagram controls the speed of an AC motor by varying the frequency and voltage of the power supplied to it.

    • An AC drive consists of a rectifier, DC link, inverter, and control circuitry.

    • The rectifier converts AC power to DC power, which is stored in the DC link.

    • The inverter converts the DC power back to AC power with variable frequency and voltage.

    • The control circuitry adjusts the frequency and volta...

  • Answered by AI
  • Q3. 3.Draw single line diagram of distribution system with proper secification.
  • Ans. 

    A single line diagram of a distribution system is required with proper specifications.

    • The diagram should show the flow of power from the source to the load

    • It should include all components such as transformers, switchgear, and cables

    • The specifications should include voltage levels, power ratings, and protection devices

    • The diagram should follow standard symbols and conventions

    • Example: A 11 kV distribution system with a 5

  • Answered by AI
  • Q4. 4.Why do the dewpoint test in transformer?
  • Ans. 

    Dewpoint test is done in transformer to check the moisture content in the insulation oil.

    • Moisture in insulation oil can cause breakdown of transformer insulation

    • Dewpoint test helps to determine the moisture content in the oil

    • It is a preventive maintenance measure to avoid transformer failure

    • The test involves cooling a mirror until dew forms on it, and measuring the temperature at which dew forms

  • Answered by AI
  • Q5. 5.What is the difference between power transformer and distribution transformer?
  • Ans. 

    Power transformers are used in transmission systems to step up or down voltage, while distribution transformers are used in distribution systems to step down voltage.

    • Power transformers are used in high voltage transmission systems to step up or down voltage for long distance transmission.

    • Distribution transformers are used in low voltage distribution systems to step down voltage for local distribution.

    • Power transformers...

  • Answered by AI
  • Q6. 6.How to work Buchholz relay in transformer.
  • Ans. 

    Buchholz relay is used to protect transformers from faults by detecting gas and oil flow abnormalities.

    • Buchholz relay is installed in the pipe connecting the transformer tank and conservator tank.

    • It operates based on the principle that faults in the transformer generate gases and cause oil flow disturbances.

    • When gas or oil flow abnormalities occur, the relay trips and sends a signal to the control panel to isolate the ...

  • Answered by AI

Interview Preparation Tips

Round: Resume Shortlist
Experience: My resume was shortlisted from naukri.com.

I appeared for an interview in May 2019.

Interview Questionnaire 

2 Questions

  • Q1. Different types of steel sections
  • Ans. 

    Steel sections are structural shapes made from steel for construction purposes.

    • I-beams

    • H-beams

    • C-channels

    • Angle sections

    • T-sections

    • Z-sections

    • Box sections

    • Circular sections

  • Answered by AI
  • Q2. Different types off load applied on long and short steel column
  • Ans. 

    Different types of loads applied on long and short steel columns

    • Long columns are more susceptible to buckling under compressive loads

    • Short columns are more susceptible to crushing under compressive loads

    • Long columns are more likely to experience bending under lateral loads

    • Short columns are more likely to experience shear under lateral loads

    • Examples of loads include dead load, live load, wind load, seismic load, etc.

  • Answered by AI

I applied via Company Website and was interviewed before Aug 2021. There was 1 interview round.

Round 1 - Technical 

(5 Questions)

  • Q1. Rectifier,half,full,bridge
  • Q2. Difference between igbt mosfet scr
  • Ans. 

    IGBT, MOSFET, and SCR are all types of power electronic devices used for switching and controlling electrical power.

    • IGBT stands for Insulated Gate Bipolar Transistor and is commonly used in high power applications such as motor drives and inverters.

    • MOSFET stands for Metal Oxide Semiconductor Field Effect Transistor and is commonly used in low power applications such as mobile devices and computers.

    • SCR stands for Silico...

  • Answered by AI
  • Q3. Converter and inverter circuit
  • Q4. Slip ring and squirrel cage motor speed slip and torque characteristics
  • Q5. Siemens plc and drives

Interview Preparation Tips

Topics to prepare for Tata Steel Junior Engineer interview:
  • Power Electronics
  • Igbt scr mosfet diode transistor
  • Motors specially focus Ac motor
Interview preparation tips for other job seekers - Be specific and to the point answer dont try to fool the invigilator if dont know be straightforward

I applied via Campus Placement and was interviewed before Sep 2021. There were 2 interview rounds.

Round 1 - HR 

(1 Question)

  • Q1. HR will ask you about their own company so before interview make sure you have atleast some knowledge of their company
Round 2 - Technical 

(1 Question)

  • Q1. You have explain about your area of interest because it's matter when your technical interview goes in the wrong direction

Interview Preparation Tips

Interview preparation tips for other job seekers - Just be with you and be confident because when you explain anything about your self or about your knowledge first thing matters that is your confidence

I applied via Walk-in and was interviewed in Jul 2021. There was 1 interview round.

Interview Questionnaire 

1 Question

  • Q1. Electrical releted questions

Interview Preparation Tips

Interview preparation tips for other job seekers - Select your company after interview

Interview Questionnaire 

2 Questions

  • Q1. Fiast focus on basic knowledge, thous are you studying?
  • Q2. You mast be knowledge of computer & XL also a sap

Jindal Stainless Interview FAQs

How many rounds are there in Jindal Stainless Electronics Engineer interview?
Jindal Stainless interview process usually has 1 rounds. The most common rounds in the Jindal Stainless interview process are HR.

Tell us how to improve this page.

Jindal Stainless Electronics Engineer Interview Process

based on 1 interview

Interview experience

5
  
Excellent
View more

Interview Questions from Similar Companies

Tata Steel Interview Questions
4.1
 • 859 Interviews
JSW Steel Interview Questions
3.9
 • 597 Interviews
JSW Group Interview Questions
3.9
 • 111 Interviews
Jindal Saw Interview Questions
4.0
 • 103 Interviews
Rashmi Metaliks Interview Questions
3.4
 • 80 Interviews
Viraj Profiles Interview Questions
3.8
 • 80 Interviews
View all
Junior Engineer
1.2k salaries
unlock blur

₹2.1 L/yr - ₹5.8 L/yr

Associate Manager
1.1k salaries
unlock blur

₹5.3 L/yr - ₹15 L/yr

Executive Engineer
689 salaries
unlock blur

₹4 L/yr - ₹11 L/yr

Assistant Engineer
654 salaries
unlock blur

₹3.2 L/yr - ₹7 L/yr

Manager
424 salaries
unlock blur

₹7.2 L/yr - ₹20.8 L/yr

Explore more salaries
Compare Jindal Stainless with

Tata Steel

4.1
Compare

JSW Steel

3.9
Compare

Jindal Steel and Power

3.9
Compare

ArcelorMittal Nippon Steel

4.1
Compare
Did you find this page helpful?
Yes No
write
Share an Interview