Filter interviews by
I applied via Naukri.com and was interviewed before Jan 2023. There was 1 interview round.
Top trending discussions
posted on 31 Dec 2022
I applied via Approached by Company and was interviewed in Dec 2022. There were 2 interview rounds.
posted on 1 Jun 2022
I applied via Referral and was interviewed before Jun 2021. There were 2 interview rounds.
Yes
Yes, I understand engineering drawings and can interpret them accurately.
Yes, I am proficient in preparing Bar Bending Schedules (BBS) for reinforcement detailing.
Yes, I have experience in quantity estimation for construction projects.
Yes, I am familiar with relevant software and tools used for these tasks.
Yes, I can provide examples of projects where I have successfully performed these tasks.
Mix grade ratio of concrete refers to the proportion of cement, sand, and aggregate used in the concrete mix.
The mix grade ratio of concrete is expressed as the proportion of cement to sand to aggregate.
The most common mix grade ratios for concrete are 1:2:3 and 1:3:6.
The mix grade ratio of concrete depends on the strength and durability required for the specific project.
The mix grade ratio of concrete can be adjusted ...
Cube test is performed to determine the compressive strength of concrete.
Prepare the cube moulds of size 150mm x 150mm x 150mm.
Clean the moulds and apply oil to the inner surface.
Fill the moulds with concrete in three layers and compact each layer.
Level the top surface and cover the moulds with a gunny bag.
After 24 hours, remove the moulds and immerse the cubes in water for curing.
After 7 days, test the cubes for compr...
Leaping length is the distance between two consecutive supports of a bridge or a beam.
Leaping length is also known as span length.
It is an important factor in the design of bridges and beams.
The leaping length determines the maximum load that the structure can bear.
For example, a bridge with a leaping length of 50 meters can bear heavier loads than a bridge with a leaping length of 30 meters.
UTM stands for Universal Transverse Mercator, a coordinate system used to locate positions on the Earth's surface.
UTM divides the Earth into 60 zones, each 6 degrees of longitude wide.
It uses a grid system to give a unique location to every point on the Earth's surface.
UTM coordinates are given in meters, making it easy to measure distances and areas.
It is commonly used in mapping, surveying, and navigation application...
The 20 in M20 refers to the compressive strength of concrete in megapascals after 28 days of curing.
M20 is a mix of concrete with a compressive strength of 20 MPa after 28 days of curing.
The compressive strength of concrete is the maximum load it can bear before crushing.
The strength of concrete depends on the ratio of cement, sand, and aggregate used in the mix.
Other grades of concrete include M10, M15, M25, M30, etc....
I applied via Referral and was interviewed before Jan 2021. There were 3 interview rounds.
Lift is a vertical transportation system that moves people or goods between floors or levels of a building.
Lifts are commonly used in high-rise buildings.
They operate using a motorized system that moves a cab or platform up and down a shaft.
Lifts can be hydraulic, traction, or pneumatic.
They are equipped with safety features such as emergency brakes and backup power supplies.
Lifts are regulated by safety codes and stan
Types of lift include hydraulic, traction, and pneumatic lifts.
Hydraulic lifts use fluid pressure to move the elevator car.
Traction lifts use cables and a counterweight to move the car.
Pneumatic lifts use air pressure to move the car.
Other types of lifts include scissor lifts, boom lifts, and platform lifts.
There are various types of elevators such as hydraulic, traction, pneumatic, residential, machine room-less, etc.
Hydraulic elevators use a hydraulic piston to move the elevator car.
Traction elevators use cables and counterweights to move the car.
Pneumatic elevators use air pressure to move the car.
Residential elevators are designed for private homes.
Machine room-less elevators do not require a separate machine room.
Fre...
I applied via Job Portal and was interviewed before May 2021. There was 1 interview round.
Interview experience
Junior Shop Manager
93
salaries
| ₹2.6 L/yr - ₹6 L/yr |
Diploma Trainee Engineer
24
salaries
| ₹1.6 L/yr - ₹2.7 L/yr |
Junior Manager
24
salaries
| ₹3.8 L/yr - ₹8 L/yr |
Design Engineer
15
salaries
| ₹1.8 L/yr - ₹6 L/yr |
Service Engineer
10
salaries
| ₹1.1 L/yr - ₹4 L/yr |
Kirloskar Electric Company
BHEL
Ashok Leyland
Mahindra Powerol