10+ Interview Questions and Answers

The first step would be to investigate the cause of the secondary core of ct being open while the feeder is still working on very less load.

• Check for any loose connections in the secondary core of ct

• Inspect for any damage or faults in the secondary core of ct

• Verify the load on the feeder to ensure it is within normal operating range

• Consult with colleagues or experts for further troubleshooting steps

High voltage testing standard as per IEC includes testing voltage for 33kV system and familiar testing kits.

• High voltage testing standard as per IEC includes IEC 60060-1 for high-voltage test techniques.

• Testing voltage for 33kV system voltage is typically around 70-80kV.

• Common testing kits for high voltage testing include insulation testers, voltage detectors, and partial discharge testers.

LIBBP and HIBBP stability and sensitivity refer to protection schemes for electrical systems. Implementing logic for one incomer and three outgoing feeders involves setting up coordination and communication between devices. BBP protection testing ensures the system operates correctly under fault conditions.

• LIBBP and HIBBP stability and sensitivity are important for ensuring reliable protection of electrical systems.

• Implementing logic for one incomer and three outgoing feeders...read more

ATS stands for Automatic Transfer Switch. It is used to automatically switch between primary and backup power sources.

• ATS is a device used to switch between primary and backup power sources in case of power failure.

• To configure ATS relay, you need to set the parameters such as voltage, frequency, and delay timings.

• Trip selection refers to the setting that determines when the ATS will switch between power sources based on certain conditions.

• Examples of trip selection criteria ...read more

Close block is a device used to short circuit the secondary of a current transformer (CT) during testing to prevent damage to the CT. No fuse or MCB is used on the CT circuit to avoid any interruption during testing.

• Close block is used to short circuit the secondary of a CT during testing to prevent damage.

• It ensures that the CT is not overloaded with excessive current during testing.

• No fuse or MCB is used on the CT circuit during testing to avoid any interruption in the curr...read more

I have 5 years of experience in substation network.

• I have worked on various substation projects, including design, testing, and commissioning.

• I have experience with different types of substation equipment and systems.

• I have successfully completed multiple substation network projects on time and within budget.

alfanar Saudi Arabia is a leading electrical engineering company in the Middle East.

• alfanar Saudi Arabia specializes in electrical engineering solutions.

• They offer a wide range of products and services including power distribution, control panels, and lighting solutions.

• The company has a strong presence in the Middle East and has completed numerous projects in the region.

• alfanar Saudi Arabia is known for its quality and reliability in the field of electrical engineering.

To manage a 10 or 15 people group at site, effective communication, delegation, and leadership skills are essential.

• Establish clear goals and expectations for the team.

• Communicate regularly and openly with the team members to ensure everyone is on the same page.

• Delegate tasks based on individual strengths and skills.

• Provide necessary resources and support to the team.

• Encourage collaboration and teamwork among the group members.

• Address conflicts or issues promptly and fairly.

• L...read more

Termination for control panel involves connecting wires from various components to the terminal blocks inside the panel.

• Identify the components that need to be connected to the control panel

• Strip the insulation off the wires to expose the conductors

• Connect the wires to the appropriate terminal blocks based on the wiring diagram

• Secure the connections with terminal screws or clamps

• Label the wires for easy identification in the future

Terminating a GIS panel involves connecting and securing the cables to the appropriate terminals.

• Identify the cables to be terminated

• Strip the insulation from the cable ends

• Connect the cables to the designated terminals

• Secure the connections with appropriate fasteners

• Test the connections to ensure they are secure and functioning properly

Termination for switch gear involves connecting the wires to the appropriate terminals for proper functioning.

• Identify the terminals for the switch gear

• Strip the insulation from the wires to expose the conductors

• Connect the wires to the corresponding terminals using appropriate connectors

• Ensure proper tightening of the connectors to secure the connection

• Test the connection to ensure it is functioning correctly

I have extensive experience in substation testing and commissioning.

• I have worked on multiple substation projects, both in testing and commissioning phases.

• I am familiar with the various equipment and systems used in substations, such as transformers, circuit breakers, relays, and control systems.

• I have conducted thorough testing of substation equipment to ensure proper functionality and adherence to specifications.

• I have participated in the commissioning process, which invol...read more

Yes, I have a transferable iqama.

• I have a transferable iqama.

• I can provide the necessary documentation to prove it.

• Having a transferable iqama allows me to work in different locations without any restrictions.

• It demonstrates my flexibility and adaptability to new environments.

To change motor rotation, swap any two of the three power supply wires.

• Swap any two of the three power supply wires to change motor rotation.

• Ensure power is disconnected before making any changes.

• Consult the motor's manual for specific instructions.

• Test the motor after making the changes to ensure it is rotating in the desired direction.

Two-way connection can be achieved by using two switches to control a single light or appliance from two different locations.

• Install two switches at different locations to control the same light or appliance

• Connect the common terminal of one switch to the phase or live wire

• Connect the common terminal of the other switch to the light or appliance

• Connect the remaining terminals of both switches to complete the circuit

• Test the connection to ensure proper functioning

The next step in SAP CRM is to transition to SAP C/4HANA for enhanced customer engagement and experience.

• Transition from SAP CRM to SAP C/4HANA for improved customer engagement

• Utilize advanced features like machine learning and AI for personalized customer interactions

• Integrate with other SAP solutions like SAP S/4HANA for seamless business processes

I handle pressure by staying calm, prioritizing tasks, and seeking help when needed.

• I take deep breaths and remind myself to stay calm

• I prioritize tasks based on urgency and importance

• I seek help from colleagues or supervisors if necessary

• I maintain a positive attitude and focus on finding solutions

• I take breaks when needed to avoid burnout