i
Yantrika Instruments
Filter interviews by
To create a thread 20x1.5 in a 2mm sheet, use a tap and die set with the appropriate size and pitch.
Select a tap and die set with a 20x1.5 size and pitch
Drill a hole in the 2mm sheet with a diameter slightly smaller than the tap size
Insert the tap into the hole and turn it clockwise to create the thread
Use the die to clean up and refine the thread
Ensure the thread is the correct size and pitch using a thread gauge
Basic knowledge of GD&T refers to understanding the symbols, rules, and principles of Geometric Dimensioning and Tolerancing.
Understanding the symbols used in GD&T such as concentricity, perpendicularity, and flatness
Knowing the rules for applying GD&T to drawings and designs
Understanding the principles of GD&T such as datum features and tolerance zones
Being able to interpret and communicate GD&T requirements to others
...
1st angle & 3rd angle projection are two methods of representing a 3D object on a 2D plane.
1st angle projection: object is placed in front of the viewing plane and the planes of projection are between the object and the viewer
3rd angle projection: object is placed behind the viewing plane and the planes of projection are between the object and the viewer
In 1st angle projection, the top view is placed above the front vi...
Top trending discussions
posted on 12 Jul 2016
I applied via Campus Placement
The question is about finding the minimum steps to reach from a source string to a destination string using three operations.
BFS and DFS are graph traversal techniques that can be used to solve this problem.
BFS is typically used when finding the shortest path or exploring all possible paths in a graph.
DFS is useful when searching for a specific path or exploring deeply into a graph.
In this case, BFS can be used to find...
posted on 14 Jul 2017
posted on 13 Aug 2024
3 rounds online, dsa, hr
posted on 22 Aug 2024
I applied via Campus Placement and was interviewed in Feb 2024. There were 3 interview rounds.
It was online coding test consist of 2 question
One from DP and other graph
One question of DP within in 45 min time constraints
Floor value of square root of a number is the largest integer less than or equal to the square root.
The floor value of square root of a number can be found using mathematical functions like floor() or integer division.
For example, the floor value of square root of 16 is 4, as sqrt(16) = 4.
For non-perfect square numbers, the floor value of square root can be calculated using approximation methods.
posted on 6 Oct 2023
I applied via Campus Placement and was interviewed in Apr 2023. There were 3 interview rounds.
Level was medium to hard
To print a tree in anticlockwise direction, start from the bottom left and traverse each level from right to left.
Start from the bottom left of the tree
Traverse each level from right to left
Print the nodes as you traverse
Some old coding platform with limited testcases
posted on 20 Nov 2024
I applied via Naukri.com and was interviewed in May 2024. There were 2 interview rounds.
Coding round where they ask few coding questions
2 coding questions, aptitude and electronics
posted on 26 Oct 2020
Gas detectors should be strategically placed in areas where gas leaks are most likely to occur.
Gas detectors should be placed near potential gas leak sources such as gas pipelines, valves, and storage tanks.
They should also be placed in areas where gas can accumulate such as low-lying areas and confined spaces.
The number of gas detectors required depends on the size of the area and the potential hazards.
Gas detectors s...
Density of gases varies based on their molecular weight and temperature.
Density is measured in kg/m³ or g/L.
At standard temperature and pressure (STP), the density of air is 1.2 kg/m³.
The density of helium is much lower than air, at 0.1785 kg/m³.
The density of carbon dioxide is higher than air, at 1.98 kg/m³.
The density of hydrogen is much lower than air, at 0.0899 kg/m³.
based on 1 review
Rating in categories
Design Engineer
5
salaries
| ₹2.5 L/yr - ₹6 L/yr |
Mechanical Engg. Design
4
salaries
| ₹2.2 L/yr - ₹2.5 L/yr |
Accountant
4
salaries
| ₹1.5 L/yr - ₹4.8 L/yr |
CNC Programmer
4
salaries
| ₹2.1 L/yr - ₹3.4 L/yr |
Sales Executive
3
salaries
| ₹2.8 L/yr - ₹2.8 L/yr |
Hykon
Chheda Electricals and Electronics
Vu Televisions
Systematic Group