Vishwa Samudra Engineering Senior Engineer Interview Questions and Answers

Q1. What is project management?
Add your answer

How to manage site structure to finishing work

Technical/ mathematics

Q1. About reinforcement
Add your answer
Q2. About tile testing
Add your answer
Q3. About material testing
Add your answer

Q1. Family background
Add your answer
Q2. Salary discussion
Add your answer

Q1. What is test procedure for Cement and steel and coarse aggregate and sand?
Ans. 
The test procedures for cement, steel, coarse aggregate, and sand involve various physical and chemical tests to ensure quality and suitability for construction purposes.
• Cement: Tests include fineness, setting time, compressive strength, soundness, and chemical composition.

• Steel: Tests involve tensile strength, yield strength, elongation, and chemical composition.

• Coarse Aggregate: Tests include sieve analysis, specific...read more
Answered by AI
Add your answer
Q2. What is the grade using of concrete?
Ans. 
The grade of concrete refers to its strength and durability.
• Concrete is graded based on its compressive strength, measured in megapascals (MPa).

• Common grades of concrete include M10, M15, M20, M25, etc.

• The higher the grade, the stronger the concrete.

• Different grades of concrete are used for different applications, such as foundations, slabs, columns, etc.
Answered by AI
Add your answer
Q3. What is the 28 days cube strength and value?
Ans. 
28 days cube strength is a measure of the compressive strength of concrete after 28 days of curing.
• 28 days cube strength refers to the compressive strength of concrete cubes after they have been cured for 28 days.

• It is an important parameter to assess the quality and durability of concrete.

• The value of 28 days cube strength is typically expressed in megapascals (MPa) or pounds per square inch (psi).

• It is determined by ...read more
Answered by AI
Add your answer

Q1. What is your previous experience
Add your answer

Q1. What is Surging?
Ans. 
Surging is a phenomenon in which a system experiences rapid and temporary increases in pressure or flow rate.
• Surging can occur in various systems such as pipelines, compressors, pumps, and turbines.

• It is often caused by sudden changes in demand, equipment malfunctions, or improper system design.

• Surging can lead to damage to equipment, reduced efficiency, and safety hazards.

• Examples include water hammer in pipelines and
Answered by AI
Add your answer
Q2. What is Froude No?
Ans. 
Froude number is a dimensionless number used to quantify the influence of gravity on fluid flow.
• Froude number is defined as the ratio of inertia force to gravitational force in a fluid flow.

• It is used to determine the type of flow (subcritical, critical, or supercritical) in open channel flow.

• Froude number is calculated as Fr = V / sqrt(g * d), where V is velocity, g is acceleration due to gravity, and d is depth of fl
Answered by AI
Add your answer
Q3. What is Weeping?
Ans. 
Weeping is the process of fluid leaking out of a solid material, often due to damage or excess moisture.
• Weeping can occur in materials such as wood, concrete, and metal.

• It is often a sign of structural damage or deterioration.

• Examples include water weeping from a crack in a wall or oil weeping from a car engine.

• Weeping can also refer to the shedding of tears in humans and animals.
Answered by AI
Add your answer

Q1. Draw basic PFD of a WTP plant including feed quality and all the sensors.
Ans. 
A basic PFD of a WTP plant including feed quality and sensors.
• Include feed quality parameters such as turbidity, pH, temperature, and flow rate

• Include sensors for monitoring parameters like chlorine levels, pressure, and conductivity

• Show the flow of water through various treatment processes like coagulation, flocculation, sedimentation, filtration, and disinfection
Answered by AI
Add your answer
Q2. What are the process checks done in Line testing of a 6inch dia pigging line including the calculations involved?
Ans. 
Process checks in line testing of a 6inch dia pigging line and associated calculations
• Pressure testing to ensure integrity of the line

• Flow testing to check for blockages or restrictions

• Calibration of pigging equipment for accurate results

• Calculations involve pressure drop, flow rate, and pigging efficiency

• Recording and analyzing data for future reference
Answered by AI
Add your answer

Q1. Why do u qant to leave ur previous company?
Add your answer
Q2. How do u solve a matter of conflict during a Project meeting?
Add your answer

Q1. Civil engineering
Add your answer
Q2. Civil engineering responsibility timely site work .
Add your answer

Q1. Civil engineering
Add your answer
Q2. Site relative question
Add your answer

Q1. Site Execution qution
Add your answer
Q2. Highway Road Project qution
Add your answer

Q1. Rate of different dia of Coupler?
Ans. 
The rate of different diameters of couplers can vary based on the specific type and manufacturer.
• The rate of different diameters of couplers can depend on factors such as material, quality, and brand.

• Some common diameters for couplers include 1/2 inch, 3/4 inch, and 1 inch.

• Rates may also vary based on the intended use of the coupler, such as for plumbing or electrical connections.
Answered by AI
Add your answer
Q2. Rate of threading dia wise?
Ans. 
Rate of threading varies based on the diameter of the thread.
• The rate of threading increases with larger thread diameters.

• Smaller thread diameters require slower threading rates to prevent damage.

• Factors such as material type and cutting tool also impact threading rate.

• For example, a 1/4 inch thread may have a different threading rate than a 1 inch thread.
Answered by AI
Add your answer

Q1. About current projects. And more about seismic/ wind loads
Add your answer
Q2. How to perform RSM method ?
Ans. 
Response Surface Methodology (RSM) is a statistical technique used to model and analyze the relationship between a response variable and multiple input variables.
• Design a set of experiments based on a factorial design

• Collect data from the experiments

• Fit a regression model to the data

• Analyze the model to determine optimal input settings for the response variable
Answered by AI
View 1 more answer
Q3. Soil test report
Add your answer
Q4. Foundation uplift
Add your answer
Q5. Connection design
Add your answer

Q1. About my role and job responsibility
Add your answer

Q1. About my current salary and expectation
Add your answer