Reliance Industries
100+ Wells Fargo Interview Questions and Answers
Q1. Explain different types of pumps and differences.
Different types of pumps and their differences.
Centrifugal pumps: used for low viscosity fluids, high flow rates, low pressure
Positive displacement pumps: used for high viscosity fluids, low flow rates, high pressure
Axial flow pumps: used for high flow rates, low pressure, low viscosity fluids
Mixed flow pumps: used for medium flow rates and pressures
Jet pumps: used for pumping fluids with high solids content
Differences include design, flow rate, pressure, viscosity, and appli...read more
Q2. What is the state when their is no effect of pressure in a pipeline
The state when there is no effect of pressure in a pipeline is called atmospheric pressure.
Atmospheric pressure is the pressure exerted by the weight of air in the atmosphere.
When the pressure inside the pipeline is equal to the atmospheric pressure outside, there is no effect of pressure.
This state is also known as zero gauge pressure or absolute pressure.
It is important to maintain this state to prevent leaks or bursts in the pipeline.
Q3. How your projects are suitable for reliance industry ?
My projects align with Reliance's focus on innovation, sustainability, and efficiency.
I have worked on projects that involve developing sustainable energy solutions, which aligns with Reliance's focus on sustainability.
I have also worked on projects that involve optimizing processes and reducing waste, which aligns with Reliance's focus on efficiency.
For example, I developed a system to monitor and optimize energy usage in a manufacturing plant, which resulted in significant ...read more
Q4. What factors will you take in consideration to check evaporator efficiency?
Factors to consider for checking evaporator efficiency
Temperature difference between inlet and outlet air
Airflow rate
Refrigerant flow rate
Frost buildup on evaporator coils
Cleanliness of evaporator coils
Type of refrigerant used
Q5. Explain refrigeration cycles and draw the cycle diagram
Refrigeration cycles are thermodynamic cycles used in refrigeration systems to transfer heat from a low-temperature region to a high-temperature region.
Refrigeration cycles involve four main components: compressor, condenser, expansion valve, and evaporator.
The cycle starts with the compressor, which increases the pressure and temperature of the refrigerant gas.
The high-pressure gas then flows into the condenser, where it releases heat to the surroundings and condenses into a...read more
Q6. What were different types of sensors used in industry like for temp,pressure, level, etc.
Various types of sensors used in industries include temperature sensors, pressure sensors, level sensors, etc.
Temperature sensors: thermocouples, resistance temperature detectors (RTDs), thermistors
Pressure sensors: piezoresistive sensors, capacitive sensors, strain gauge sensors
Level sensors: ultrasonic sensors, capacitive sensors, float sensors
Flow sensors: electromagnetic flow meters, ultrasonic flow meters, thermal mass flow meters
Proximity sensors: inductive sensors, cap...read more
Q7. Explain different types of boilers
Boilers are vessels that heat water or other fluids to generate steam or hot water for various applications.
Fire-tube boilers: hot gases pass through tubes immersed in water
Water-tube boilers: water flows through tubes and hot gases surround them
Electric boilers: use electricity to generate heat instead of burning fuel
Condensing boilers: extract additional heat from the exhaust gases to increase efficiency
Package boilers: pre-designed and assembled in a factory for easy insta...read more
Q8. 6. What is the significance of Viscosity Index of lube?
Viscosity Index of lube measures its resistance to change in viscosity with temperature.
Viscosity Index (VI) is an important property of lubricating oils.
It measures the oil's ability to maintain its viscosity under different temperature conditions.
Higher VI means the oil's viscosity changes less with temperature, indicating better performance.
VI is calculated using kinematic viscosity measurements at two different temperatures.
For example, a high VI oil like Mobil 1 Syntheti...read more
Q9. What are the different kinds of distillation you know?
Different kinds of distillation include simple distillation, fractional distillation, steam distillation, and vacuum distillation.
Simple distillation is used to separate liquids with different boiling points.
Fractional distillation is used to separate liquids with similar boiling points.
Steam distillation is used to extract essential oils from plants.
Vacuum distillation is used to separate liquids with high boiling points.
Other types of distillation include azeotropic distill...read more
Q10. Difference between pumps and compressors
Pumps move liquids, compressors move gases.
Pumps are used to move liquids from one place to another, while compressors are used to increase the pressure of gases.
Pumps are typically used in industries such as water treatment, oil and gas, and chemical processing, while compressors are used in industries such as refrigeration, air conditioning, and power generation.
Examples of pumps include centrifugal pumps, positive displacement pumps, and submersible pumps, while examples o...read more
Q11. Difference between hardness and toughness
Hardness is resistance to indentation while toughness is resistance to fracture.
Hardness is a measure of how easily a material can be scratched or dented.
Toughness is a measure of how much energy a material can absorb before fracturing.
Hardness is often measured using the Mohs scale, while toughness is measured using impact tests.
For example, diamond is very hard but not very tough, while rubber is not very hard but very tough.
Q12. How to calculate the number of trays in distillation column
To calculate the number of trays in a distillation column, use the McCabe-Thiele method.
Determine the desired purity of the top and bottom products
Calculate the minimum reflux ratio using the Fenske equation
Use the operating line and equilibrium curve to plot the number of theoretical trays
Add a few extra trays for safety margin
Consider other factors such as pressure drop and column diameter
Example: A distillation column with a feed of 1000 kg/hr and a desired purity of 99% r...read more
Q13. What if the formula for heat engine? Explain with an example
The formula for heat engine is Q_h = Q_c + W, where Q_h is the heat absorbed, Q_c is the heat released, and W is the work done.
Heat engine converts thermal energy into mechanical energy
The formula relates the heat absorbed, heat released, and work done
Example: A car engine converts heat from burning fuel into mechanical energy to move the car
Q14. why the gibbs free energy is called free energy?
Gibbs free energy is called free energy because it is the energy available to do work at constant temperature and pressure.
Gibbs free energy is the maximum amount of work that can be obtained from a system at constant temperature and pressure.
It takes into account both the enthalpy and entropy of a system.
If the Gibbs free energy is negative, the reaction is spontaneous and can do work.
Examples include the combustion of fuels and the formation of crystals from a solution.
Q15. Why the composition of LPG cylinder varies in North and in South?
Composition of LPG cylinder varies in North and South due to differences in climate and altitude.
North India has colder climate and higher altitude, hence LPG cylinders have higher propane content to ensure proper combustion.
South India has warmer climate and lower altitude, hence LPG cylinders have higher butane content to prevent vaporization.
The composition also varies based on the source of LPG and the refining process.
The difference in composition can affect the efficien...read more
Q16. Electrical Students tell me about yourself Transimission line protrction scheme overhead vs underground transmission Which material is used in transmission why that material used Transformer protection
I am an electrical student with knowledge in transmission line protection schemes, overhead vs underground transmission, materials used in transmission, and transformer protection.
Transmission line protection schemes are designed to detect and isolate faults in the transmission line to prevent damage to equipment and ensure power continuity.
Overhead transmission lines are cheaper to install but are more susceptible to damage from weather conditions, while underground transmis...read more
Q17. What is wet bulb temperature and where is it used?
Wet bulb temperature is the temperature recorded by a thermometer covered in water-soaked cloth over which air is passed, used in meteorology and HVAC systems.
Wet bulb temperature is a measure of the lowest temperature that can be achieved by evaporating water into the air.
It is commonly used in meteorology to calculate humidity and in HVAC systems to determine the cooling potential of air.
Wet bulb temperature is always lower than the dry bulb temperature, as the evaporation ...read more
Q18. Relief valve and where it is used
Relief valve is a safety device used to prevent overpressure in a system.
It is used in various industries such as oil and gas, chemical, and power plants.
It opens when the pressure inside the system exceeds the set limit, allowing the excess pressure to escape.
It helps prevent damage to equipment and potential hazards to personnel.
Examples include pressure relief valves in boilers, safety valves in pipelines, and relief valves in hydraulic systems.
Q19. Define creep, failure and fracture.
Creep is the gradual deformation of a material under constant stress. Failure is the inability of a material to perform its intended function. Fracture is the separation of a material into two or more pieces due to stress.
Creep occurs over time and can lead to permanent deformation.
Failure can occur due to various reasons such as overloading, fatigue, corrosion, etc.
Fracture can be ductile or brittle depending on the material and the type of stress applied.
Examples of failure...read more
Q20. Principles behind some of the temprature and level measuring instruments
Temperature and level measuring instruments operate on principles such as thermal expansion, pressure, and capacitance.
Thermocouples measure temperature based on the voltage produced by two dissimilar metals when heated
RTDs (Resistance Temperature Detectors) measure temperature based on the change in resistance of a metal wire with temperature
Level sensors use principles such as buoyancy, pressure, and capacitance to measure the level of a liquid or solid
Ultrasonic level sens...read more
Q21. What is cavitation? How can we avoid it?
Cavitation is the formation of vapor bubbles in a liquid due to rapid changes in pressure. It can cause damage to equipment.
Cavitation occurs when the pressure in a liquid drops below its vapor pressure, causing bubbles to form and collapse rapidly.
It can occur in pumps, propellers, and valves, leading to erosion and damage to the equipment.
To avoid cavitation, maintain proper pressure levels in the system, use materials resistant to cavitation damage, and ensure smooth flow ...read more
Q22. what is the composition of LPG cylinder?
LPG cylinder is made up of steel and consists of propane and butane gases.
LPG cylinder is made up of high-quality steel to withstand high pressure.
It consists of a valve, pressure relief valve, and a safety cap.
The cylinder is filled with a mixture of propane and butane gases.
The composition of the gas mixture varies depending on the climate and altitude.
LPG cylinders are color-coded to indicate the type of gas and its intended use.
Q23. What is instrumentation all about?
Instrumentation is the science of measuring and controlling physical variables such as temperature, pressure, flow, and level.
Instrumentation involves the use of sensors, transmitters, and controllers to measure and control physical variables.
Examples of instrumentation include temperature sensors in a furnace, pressure transmitters in a pipeline, flow meters in a chemical plant, and level sensors in a tank.
Instrumentation is used in various industries such as oil and gas, ch...read more
Q24. what are the maxwell's equations?
Maxwell's equations describe the behavior of electromagnetic fields.
There are four equations: Gauss's law, Gauss's law for magnetism, Faraday's law, and Ampere's law with Maxwell's addition.
Together, these equations explain how electric and magnetic fields interact and propagate through space.
Maxwell's equations are fundamental to the study of electromagnetism and have many practical applications, such as in the design of electrical circuits and the development of communicati...read more
Q25. Types of cooling towers and their differences?
Cooling towers are heat rejection devices used to transfer process waste heat to the atmosphere. They can be classified into natural draft, mechanical draft, and hybrid cooling towers.
Natural draft cooling towers rely on natural convection to circulate air, while mechanical draft cooling towers use fans to force air circulation.
Hybrid cooling towers combine features of both natural draft and mechanical draft cooling towers.
Cooling towers can also be categorized based on the t...read more
Q26. Designing of Distillation Column?
Designing of Distillation Column
Determine the desired separation
Select the appropriate column type
Calculate the number of theoretical plates
Determine the feed location and reflux ratio
Design the reboiler and condenser
Select appropriate materials of construction
Consider safety and environmental factors
Q27. Characteristics curves of pump NPSH and Cavitation in pump
Characteristics curves of pump include NPSH and cavitation, important for pump performance and efficiency.
Characteristics curves show the relationship between pump performance parameters like flow rate, head, efficiency, and power consumption.
NPSH (Net Positive Suction Head) is the margin of pressure above vapor pressure required at the pump inlet to prevent cavitation.
Cavitation occurs when the pressure at the pump inlet drops below the vapor pressure of the liquid, causing ...read more
Q28. Energy forms Laws of thermodynamics Diamond strength reason
Energy forms include potential and kinetic energy. Laws of thermodynamics govern energy transfer. Diamond strength is due to its strong covalent bonds.
Energy forms include potential energy (stored energy) and kinetic energy (energy of motion)
First law of thermodynamics states that energy cannot be created or destroyed, only transferred or converted
Second law of thermodynamics states that entropy (disorder) in a closed system will always increase over time
Diamond strength is d...read more
Q29. Simulation work & software used
Simulation work involves using software to model and analyze systems or processes.
Simulation work is used in various fields such as engineering, physics, and economics.
Software commonly used for simulation work includes MATLAB, Simulink, and ANSYS.
Simulation work can be used to optimize designs, predict performance, and identify potential issues.
Simulation work can also be used to train individuals in various scenarios, such as flight simulators for pilots.
Simulation work is ...read more
Q30. What is your DDP?
DDP stands for Daily Development Plan, which is a plan that outlines the tasks and goals for the day.
DDP is a daily plan that helps individuals prioritize their tasks and achieve their goals for the day
It includes a list of tasks to be completed, deadlines, and priorities
DDP helps in time management and ensures that important tasks are not missed
For example, a software developer's DDP may include coding, testing, and debugging tasks for the day
Q31. What is Boiling point, NPSH, Burnoli eqation, Distilation, reflux ratio, mass transfer basic, types of pump and valve, Types of polimer, Basic of Hydrocarbon.
The question covers various topics related to field executive role, including boiling point, NPSH, Burnoli equation, distillation, reflux ratio, mass transfer basics, types of pumps and valves, types of polymers, and basics of hydrocarbon.
Boiling point is the temperature at which a substance changes from a liquid to a gas.
NPSH (Net Positive Suction Head) is a measure of the pressure available at the suction port of a pump.
Burnoli equation is a mathematical equation used to ca...read more
Q32. Explain about designing of distillation coulmn
Designing a distillation column involves determining the number of trays, column diameter, and reflux ratio.
Consider the desired separation efficiency and capacity when determining the number of trays.
Calculate the column diameter based on the vapor and liquid flow rates.
Select an appropriate reflux ratio to achieve the desired separation.
Consider factors such as pressure, temperature, and composition of the feed when designing the column.
Use simulation software like Aspen Pl...read more
Q33. Types of pumps?
Types of pumps include centrifugal pumps, reciprocating pumps, and rotary pumps.
Centrifugal pumps: use a rotating impeller to increase the pressure of a fluid.
Reciprocating pumps: use a piston or diaphragm to displace the fluid.
Rotary pumps: use rotating mechanisms to move the fluid, such as gear pumps or screw pumps.
Q34. Types of valves?
Valves are devices used to control the flow of fluids or gases in a system.
Gate valve - used to fully open or close the flow of fluid
Ball valve - uses a rotating ball to control flow
Check valve - allows flow in one direction only
Butterfly valve - uses a disc to control flow
Needle valve - used for precise flow control
Q35. Pump and turbine efficiency derivations
Pump and turbine efficiency derivations
Efficiency of a pump is the ratio of the work done on the fluid to the energy supplied to the pump.
Efficiency of a turbine is the ratio of the work done by the turbine to the energy available in the fluid.
Pump efficiency can be calculated using the formula: Efficiency = (Output power / Input power) * 100%
Turbine efficiency can be calculated using the formula: Efficiency = (Output power / Input power) * 100%
Efficiency can be improved by r...read more
Q36. DISTILLATION COLUMN DESIGN IN DETAIL
Distillation column design involves determining the number of trays, column diameter, reflux ratio, and feed location.
Determine the number of trays needed for separation efficiency.
Calculate the column diameter based on vapor and liquid flow rates.
Select the appropriate reflux ratio for desired separation.
Choose the optimal feed location for efficiency.
Consider factors such as pressure, temperature, and composition in design.
Example: Designing a distillation column for separa...read more
Q37. HEAT EXCHANGER DESIGN IN DETAIL
Heat exchanger design involves selecting appropriate materials, determining size and shape, and optimizing flow patterns for efficient heat transfer.
Selecting appropriate materials based on compatibility with fluids and operating conditions
Determining size and shape based on heat transfer requirements and space constraints
Optimizing flow patterns to maximize heat transfer efficiency, such as using fins or turbulators
Considering factors like pressure drop, fouling, and mainten...read more
Q38. Heat treatment process?
Heat treatment process involves heating and cooling metals to alter their physical and mechanical properties.
Heating the metal to a specific temperature
Holding the metal at that temperature for a certain period of time
Cooling the metal at a controlled rate
Types of heat treatment include annealing, tempering, quenching, and normalizing
Q39. Different types of pumps ?
Different types of pumps include centrifugal pumps, reciprocating pumps, and rotary pumps.
Centrifugal pumps use centrifugal force to move fluids.
Reciprocating pumps use a piston or diaphragm to create pressure.
Rotary pumps use rotating mechanisms to move fluids.
Other types of pumps include gear pumps, peristaltic pumps, and jet pumps.
Q40. What is Distillation and explain it in detail.
Distillation is a process of separating components of a liquid mixture based on differences in boiling points.
Distillation involves heating the liquid mixture to create vapor, then cooling the vapor to condense it back into liquid form.
The components with lower boiling points will vaporize first and be collected, leaving behind the components with higher boiling points.
Examples of distillation include the separation of alcohol from water in the production of spirits, and the ...read more
Q41. What is types of pumps and Valves.
Types of pumps include centrifugal, reciprocating, and rotary pumps. Types of valves include gate, globe, ball, and butterfly valves.
Types of pumps: centrifugal, reciprocating, rotary
Types of valves: gate, globe, ball, butterfly
Examples: Centrifugal pump, Gate valve
Q42. What is vessels and explain in detail.
Vessels are tubular structures that carry fluids throughout the body, such as blood vessels and lymphatic vessels.
Vessels can be classified into different types based on their function, such as arteries, veins, and capillaries.
Arteries carry oxygen-rich blood away from the heart, while veins carry oxygen-poor blood back to the heart.
Capillaries are tiny blood vessels that connect arteries and veins, allowing for the exchange of nutrients and waste products.
Lymphatic vessels a...read more
Q43. What is best idea for development ?
The best idea for development is to provide personalized learning experiences for students.
Implementing individualized learning plans based on students' strengths and weaknesses
Using technology to create interactive and engaging lessons
Encouraging student collaboration and problem-solving skills
Providing ongoing professional development for teachers
Creating a supportive and inclusive learning environment
Q44. Q1 Types Of foundation Q2 Volume of one cement bag Q3 how much bricks are need for 1M3 Brick Masonry Q4 concrete mould size Q5 Ratio of M15 Grade concert Q6 bottom clear cover of Foundation as per IS CODE
Interview questions for Civil Site Engineer including foundation types, cement bag volume, brick masonry, concrete mould size, M15 grade ratio, and bottom clear cover of foundation.
Types of foundation include shallow, deep, and special foundations
Volume of one cement bag is typically 0.0347 cubic meters or 1.226 cubic feet
Approximately 500 bricks are needed for 1M3 brick masonry
Concrete mould size varies depending on the project requirements
Ratio of M15 grade concrete is 1:2:...read more
Q45. How to BBS Calculation and MB preparation
BBS Calculation and MB preparation involve analyzing data and creating reports for decision-making.
Collect relevant data for BBS Calculation and MB preparation
Analyze the data to identify trends and patterns
Use appropriate tools and software for calculations
Prepare reports with key findings and recommendations
Present the reports to stakeholders for decision-making
Q46. What is Site excutive role and responsibilities
Site executives oversee operations at a specific location, ensuring smooth functioning and achieving organizational goals.
Managing day-to-day operations at the site
Supervising staff and ensuring they are properly trained
Implementing and enforcing company policies and procedures
Monitoring performance metrics and making adjustments as needed
Communicating with upper management to provide updates and address any issues
Ensuring compliance with regulations and safety standards
Handl...read more
Q47. Type of permit and how to work with permit
Different types of permits are required for various activities, and working with permits involves understanding the regulations, applying for the permit, and complying with its conditions.
Identify the specific type of permit required for the activity or project.
Research the regulations and requirements for obtaining the permit.
Submit the necessary documentation and application forms to the relevant authority.
Ensure compliance with the conditions and restrictions outlined in t...read more
Q48. In a shell and tube heat exchanger, where does a toxic fluid go into?
Toxic fluid in a shell and tube heat exchanger goes into the tube side.
Toxic fluid is typically directed into the tubes of the heat exchanger.
This is done to prevent contamination of the environment or other fluids in the system.
Examples include chemical processing plants where toxic fluids need to be cooled or heated efficiently.
Q49. What is width of pavement in two lines road with out kerb?
The width of pavement in a two-lane road without kerb depends on the traffic volume and speed.
The width can range from 6 to 12 meters.
Higher traffic volume and speed require wider pavement.
The pavement width should also consider the type of vehicles using the road.
The absence of kerb means the pavement should be wider to accommodate vehicles that may stray off the road.
The width of pavement should also consider the road alignment and terrain.
A wider pavement can also provide ...read more
Q50. Type of boilers.... Type of jig Type of fixtures..
The question is not related to Mechanical Maintenance Engineering. It seems to be about manufacturing.
The question is not relevant to the job position.
Boilers are not related to jigs and fixtures.
The interviewer may have made a mistake or was testing the candidate's ability to handle unexpected questions.
Q51. What means M25 Grade of concrete
M25 Grade of concrete refers to the mix ratio of cement, sand, and aggregate used in construction.
M25 Grade of concrete has a compressive strength of 25 MPa (megapascals) after 28 days of curing.
The mix ratio for M25 Grade concrete is 1:1:2 (1 part cement, 1 part sand, 2 parts aggregate).
It is commonly used in the construction of residential buildings, bridges, and pavements.
Q52. Tell the working principle of industrial compressors
Industrial compressors work by increasing the pressure of a gas to create mechanical energy.
Industrial compressors use a motor to draw in and compress gas, then release it at a higher pressure.
The compressed gas can be used for various industrial applications such as powering pneumatic tools or HVAC systems.
Common types of industrial compressors include reciprocating, rotary screw, and centrifugal compressors.
Q53. What is ohms law
Ohm's law states that the current through a conductor between two points is directly proportional to the voltage across the two points.
Ohm's law is represented by the equation I = V/R, where I is the current, V is the voltage, and R is the resistance.
It is used to calculate the current flowing through a circuit given the voltage and resistance.
It can also be used to calculate the resistance of a circuit given the voltage and current.
Ohm's law only applies to conductors that h...read more
Q54. What is the third law of thermodynamics ?
The third law of thermodynamics states that the entropy of a perfect crystal at absolute zero is zero.
The third law of thermodynamics states that as the temperature of a system approaches absolute zero, the entropy of the system also approaches zero.
It is impossible to reach absolute zero in practice, but this law helps in understanding the behavior of systems at extremely low temperatures.
This law is important in the study of phase transitions and the behavior of matter at v...read more
Q55. What do you mean by new technologies in india
New technologies in India refer to the latest advancements and innovations in various fields.
India is rapidly developing in the field of Artificial Intelligence (AI) and Machine Learning (ML)
Internet of Things (IoT) is gaining popularity in India with the rise of smart cities
Blockchain technology is being explored in various industries such as finance and healthcare
India is also making strides in renewable energy technologies such as solar and wind power
Virtual and Augmented ...read more
Q56. What is relay
A relay is an electrically operated switch that uses an electromagnet to mechanically control the opening and closing of contacts.
Relays are commonly used in electrical systems to control high-power devices with low-power signals.
They can be used to control motors, lights, solenoids, and other electrical components.
Relays have an input coil that generates a magnetic field when current flows through it, causing the contacts to open or close.
They provide isolation between the c...read more
Q57. What is the use of Nano technology in now days
Nano technology is used in various fields like medicine, electronics, energy, and materials science.
In medicine, it is used for drug delivery, imaging, and tissue engineering.
In electronics, it is used for making smaller and more efficient devices.
In energy, it is used for improving solar cells and batteries.
In materials science, it is used for creating stronger and lighter materials.
Examples include nanorobots for targeted drug delivery, nanosensors for detecting diseases, a...read more
Q58. What is SSD in single lane two way road?
SSD stands for Safe Stopping Distance in a single lane two way road.
SSD is the minimum distance required for a vehicle to come to a complete stop in case of an emergency.
It is calculated based on the speed limit of the road and the type of vehicle.
SSD is important for ensuring road safety and preventing accidents.
For example, if the speed limit is 60 km/h, the SSD for a car would be around 73 meters.
SSD can be affected by factors such as weather conditions, road surface, and ...read more
Q59. Give me an example when you had to compromise code quality to meet a deadline
I have never compromised code quality to meet a deadline.
I prioritize planning and time management to ensure that deadlines are met without sacrificing code quality.
I communicate with stakeholders to set realistic expectations and adjust timelines if necessary.
I always strive to write clean, efficient, and maintainable code, even under tight deadlines.
I have experience working on agile teams, which emphasizes continuous delivery and iterative development.
I believe that compro...read more
Q60. What are shear force and bending moment diagrams?
Shear force and bending moment diagrams are graphical representations of internal forces in a structural element.
Shear force diagram shows the variation of shear force along the length of the beam.
Bending moment diagram shows the variation of bending moment along the length of the beam.
Shear force is the force that acts parallel to the cross-section of the beam, while bending moment is the moment that causes bending of the beam.
These diagrams are essential for analyzing the s...read more
Q61. What are the protocol for covid19?
Protocols for COVID-19 include wearing masks, social distancing, hand hygiene, and vaccination.
Wear masks in public settings and around people outside of your household
Maintain at least 6 feet of distance from others
Wash hands frequently with soap and water for at least 20 seconds
Get vaccinated when eligible
Stay home and isolate if you are sick or have been in close contact with someone who has COVID-19
Q62. What is the rulling gradient of road?
The ruling gradient of a road is the maximum gradient allowed for a particular stretch of road.
It is the steepest gradient that can be used for a particular stretch of road.
It is determined by factors such as the type of vehicle, road conditions, and safety considerations.
The ruling gradient is usually expressed as a percentage or a ratio.
For example, a ruling gradient of 1 in 20 means that for every 20 meters of horizontal distance, the road can rise by 1 meter.
Exceeding the...read more
Q63. Reason and remedial action of corrosion of steel present in RCC slab,columna and beam of structures?
Corrosion of steel in RCC structures can be caused by exposure to moisture, oxygen, and chemicals, leading to structural deterioration.
Corrosion occurs when steel in RCC structures is exposed to moisture, oxygen, and chemicals.
Remedial actions include applying protective coatings, using corrosion-resistant steel, and ensuring proper drainage to prevent water accumulation.
Regular inspections and maintenance can help identify and address corrosion issues before they cause signi...read more
Q64. Leakage of RCC slab in rainy season and it's permanent solution?
Leakage of RCC slab in rainy season can be caused by cracks, improper waterproofing, or poor construction. The permanent solution involves repairing cracks, applying waterproofing coatings, and ensuring proper drainage.
Identify and repair any cracks in the RCC slab
Apply waterproofing coatings to prevent water penetration
Ensure proper slope and drainage to prevent water accumulation
Use quality materials and proper construction techniques during slab installation
Q65. Brief the functions and responsibilities of the Stores, warehouse and logistic in MM.
Q66. mentioned Standard maintenance procedure for instruments
Standard maintenance procedures for instruments involve regular inspections, calibrations, and repairs to ensure optimal performance.
Regularly inspect instruments for any signs of wear or damage
Calibrate instruments according to manufacturer's guidelines
Perform routine maintenance tasks such as cleaning and lubricating
Keep detailed records of maintenance activities for each instrument
Train staff on proper instrument maintenance procedures
Schedule preventive maintenance to avo...read more
Q67. Overhauling procedure of centrifugal pump
The overhauling procedure of a centrifugal pump involves disassembling, inspecting, repairing/replacing components, and reassembling the pump.
Start by shutting off power to the pump and draining the system
Remove the pump casing and impeller to access internal components
Inspect components for wear, damage, or corrosion
Repair or replace damaged components such as bearings, seals, or impeller
Reassemble the pump, ensuring proper alignment and tightness of components
Test the pump ...read more
Q68. What is your biggest achievement? How will yoi handle customer queries
My biggest achievement is successfully leading a team to exceed sales targets by 30% in one quarter.
I will handle customer queries by actively listening to their concerns and providing personalized solutions.
I will ensure prompt responses to customer queries through various communication channels such as phone, email, and live chat.
I will escalate complex queries to the appropriate department or manager for resolution.
I will follow up with customers to ensure their queries ha...read more
Q69. What is difference between pump and compressor.
Pumps are used to move fluids, while compressors are used to increase the pressure of gases.
Pumps are used to transfer fluids from one place to another, while compressors are used to increase the pressure of gases.
Pumps work with liquids, while compressors work with gases.
Pumps generally have a lower pressure ratio compared to compressors.
Examples: Water pump for irrigation, air compressor for pneumatic tools.
Q70. What is tha defrans of oil and gas
Oil and gas are fossil fuels that are extracted from the earth and used as sources of energy.
Oil and gas are hydrocarbons, meaning they are composed of hydrogen and carbon atoms.
Oil is a liquid fossil fuel that is formed from the remains of ancient marine organisms.
Gas refers to natural gas, which is primarily composed of methane and is found in underground reservoirs.
Both oil and gas are extracted through drilling wells and are used as sources of energy for various purposes,...read more
Q71. Section 89 of the cost act
Section 89 of the cost act deals with the power of the court to order costs.
Section 89 allows the court to order costs in any proceedings.
The court has the discretion to determine the amount of costs to be paid.
Costs can include legal fees, court fees, and other expenses incurred during the proceedings.
Q72. What is Bernoulli Equation?
Bernoulli Equation is a fundamental principle in fluid dynamics that relates the pressure, velocity, and height of a fluid.
It describes the conservation of energy in a fluid system.
It is used to calculate the flow rate of fluids through pipes and channels.
It is applicable to both incompressible and compressible fluids.
It is commonly used in aviation to explain the lift force on an airplane wing.
The equation is P + 1/2pv^2 + pgh = constant, where P is pressure, v is velocity, ...read more
Q73. how do u design a distillation column?
Designing a distillation column involves determining the required specifications, selecting appropriate materials, and optimizing the column design.
Determine the desired separation specifications
Select appropriate materials for the column
Optimize the column design for efficiency and cost-effectiveness
Consider factors such as pressure, temperature, and flow rate
Perform simulations and calculations to ensure optimal performance
Consider safety and environmental factors
Q74. What is azeotrope? Give an example.
An azeotrope is a mixture of two or more liquids that boils at a constant temperature and has the same composition in vapor and liquid phase.
Azeotropes cannot be separated by simple distillation.
Examples include ethanol and water, which form an azeotrope at 95.6% ethanol and 4.4% water.
Azeotropes are important in chemical engineering and can be used to purify chemicals.
Azeotropes can be either minimum boiling or maximum boiling.
In a minimum boiling azeotrope, the boiling poin...read more
Q75. What is smart devices
Smart devices are electronic devices that can connect to the internet and communicate with other devices to perform various tasks.
Smart devices are designed to make our lives easier and more convenient.
They can be controlled remotely using a smartphone or other device.
Examples of smart devices include smart thermostats, smart speakers, and smart security systems.
Q76. What is mca uses of mca
MCA stands for Master of Computer Applications. It is a postgraduate degree in computer science and its applications.
MCA is a professional degree that focuses on the development of computer software and applications.
It covers subjects like programming languages, database management, software engineering, and computer networks.
MCA graduates can work as software engineers, system analysts, software consultants, web developers, etc.
They can develop software solutions, manage dat...read more
Q77. Remove fitment work checking injector change
To remove fitment work checking injector change in ITI Fitter
Identify the injector that needs to be changed
Remove the old injector carefully
Clean the area around the injector
Install the new injector properly
Check for any leaks or damages
Test the injector to ensure proper functioning
Q78. ON LOAD TAP CHANGERS VS OFF LOAD TAP CHANGERS
On load tap changers adjust the transformer winding ratio while the transformer is energized, while off load tap changers require the transformer to be de-energized for adjustment.
On load tap changers allow for continuous adjustment of the transformer winding ratio without interrupting power supply.
Off load tap changers require the transformer to be taken offline for adjustment, leading to downtime.
On load tap changers are more complex and expensive compared to off load tap c...read more
Q79. What is B2B and B2C Business
Q80. What is the gate valve?
A gate valve is a type of valve that uses a gate or wedge to control the flow of fluid through a pipe.
Gate valves are commonly used in applications where a straight-line flow of fluid and minimum restriction is desired.
They are typically either fully open or fully closed, making them ideal for on/off control.
Gate valves are not suitable for regulating flow, as they tend to cause turbulence and pressure drop when partially open.
Examples of gate valves include wedge gate valves...read more
Q81. What is Distillation?
Distillation is a process of separating components of a liquid mixture based on differences in boiling points.
Distillation involves heating the liquid mixture to create vapor, then cooling the vapor to condense it back into liquid form.
The components with lower boiling points will vaporize first and be collected, leaving behind components with higher boiling points.
Examples of distillation include the separation of alcohol from water in the production of spirits, and the puri...read more
Q82. What is your Aim in Reliance jio .
My aim in Reliance Jio is to contribute towards the company's growth and success by utilizing my skills and knowledge in the role of ASM Assistant.
To support the ASM in achieving sales targets and objectives
To assist in managing and coordinating the activities of the sales team
To provide excellent customer service and ensure customer satisfaction
To analyze market trends and competitor activities to identify opportunities for growth
To continuously learn and develop new skills ...read more
Q83. What is master detail relationship
Master-detail relationship is a type of relationship in Salesforce where the master object controls certain behaviors of the detail object.
Master-detail relationship is a parent-child relationship between two objects.
The master object is the controlling object and the detail object is the dependent object.
Deleting the master record automatically deletes the associated detail records.
Security and sharing settings of the master record are inherited by the detail records.
Roll-up...read more
Q84. process of different equipments. pump curves.
Understanding the process of different equipments involves analyzing pump curves to determine performance characteristics.
Pump curves show the relationship between flow rate, head, and efficiency of a pump.
They help in selecting the right pump for a specific application based on required flow rate and head.
Pump curves also indicate the operating range of a pump and its efficiency at different operating points.
Q85. What is educational background?
Bachelor's degree in Mechanical Engineering from ABC University
Bachelor's degree in Mechanical Engineering
Graduated from ABC University
Courses in thermodynamics, fluid mechanics, and materials science
Hands-on experience with CAD software
Q86. SAP T codes with effect reflection
Q87. explain what is volatality
Volatility refers to the degree of variation of a trading price series over time.
Volatility measures the rate at which the price of a security increases or decreases.
High volatility indicates large price swings, while low volatility indicates smaller price movements.
Examples of volatile assets include cryptocurrencies and certain stocks.
Q88. What is software engineer
A software engineer is a professional who designs, develops, and maintains software applications.
Software engineers use programming languages and tools to create software solutions.
They analyze user needs and design software systems to meet those requirements.
Software engineers write code, test and debug software, and collaborate with other team members.
They may specialize in areas such as web development, mobile app development, or database management.
Examples of software en...read more
Q89. explain the process of distillation
Distillation is a process of separating components of a liquid mixture based on differences in boiling points.
Boiling the liquid mixture to create vapor
Collecting and condensing the vapor back into liquid form
Separating the components based on their different boiling points
Examples: Distilling alcohol to make spirits, purifying water through distillation
Q90. explain design of heat exchanger
A heat exchanger is a device used to transfer heat between two or more fluids.
Heat exchangers can be classified based on their construction (e.g. shell and tube, plate, finned tube)
They work on the principle of heat transfer through conduction, convection, or radiation
Common applications include HVAC systems, refrigeration units, and industrial processes
Q91. How to install temperature transmitter
To install a temperature transmitter, you need to properly mount the transmitter, connect the wiring, configure the settings, and test the transmitter.
Mount the temperature transmitter in a suitable location near the temperature source.
Connect the wiring according to the manufacturer's instructions, ensuring proper grounding.
Configure the settings such as range, output signal, and calibration using the transmitter's display or software.
Test the transmitter by comparing the di...read more
Q92. What is w o d?
W O D stands for Workout of the Day, a term commonly used in fitness communities.
W O D refers to a daily exercise routine or workout that is typically performed in fitness centers or gyms.
It is often used in CrossFit training, where each day a different workout is prescribed.
W O Ds can include a combination of various exercises such as weightlifting, cardio, and bodyweight movements.
The purpose of W O Ds is to challenge and improve overall fitness and performance.
Example: Tod...read more
Q93. tests of bricks,cement
Tests of bricks and cement are essential for ensuring quality and durability in construction projects.
Bricks can be tested for compressive strength, water absorption, efflorescence, and dimensions.
Cement can be tested for fineness, setting time, compressive strength, and soundness.
Various standard tests like compressive strength test, water absorption test, and soundness test are conducted to assess the quality of bricks and cement.
Testing methods such as ASTM standards and I...read more
Q94. what is the term q
The term 'q' can refer to various things depending on the context, such as a variable in mathematics or physics, a quality factor in engineering, or a question in general.
In mathematics, 'q' is often used as a variable in equations, such as in algebra or calculus.
In physics, 'q' can represent charge, heat, or momentum, depending on the specific equation or context.
In engineering, 'q' may refer to the quality factor of a system, representing the ratio of energy stored to energ...read more
Q95. Beams of uniform strength
Beams of uniform strength have constant cross-sectional area and moment of inertia along their length.
Beams of uniform strength have a constant cross-sectional area, meaning the beam's width and height remain the same along its length.
The moment of inertia of beams of uniform strength also remains constant throughout their length, ensuring consistent bending behavior.
Examples of beams of uniform strength include I-beams and rectangular beams with constant dimensions.
Q96. Hod quotation for filed
I'm sorry, but the question is not clear. Could you please rephrase it?
Q97. laws of thermo ,si/ci engine
The laws of thermodynamics govern the behavior of energy in systems, while SI and CI engines are types of internal combustion engines.
The laws of thermodynamics include the first law (conservation of energy), second law (entropy always increases), and third law (absolute zero cannot be reached).
SI engines (spark ignition) use a spark plug to ignite the fuel-air mixture, commonly found in gasoline-powered vehicles.
CI engines (compression ignition) rely on the heat generated by...read more
Q98. What is Good ROI
Good ROI refers to a high return on investment, indicating that the investment has generated significant profits or benefits.
Good ROI is a measure of the profitability or success of an investment.
It indicates that the investment has generated more returns than the initial investment.
A good ROI varies depending on the industry and the specific investment.
For example, a 20% ROI may be considered good in the stock market, while a 100% ROI may be considered good in real estate.
A ...read more
Q99. explain t-x-y curve
The t-x-y curve is a graph that shows the relationship between temperature (t), composition (x), and phase equilibrium (y) in a system.
The t-x-y curve is commonly used in chemical engineering to analyze phase behavior in systems with multiple components.
It shows how the temperature affects the composition of the phases present in the system at equilibrium.
The curve typically consists of two lines representing the compositions of the liquid and vapor phases, with a point where...read more
Q100. Types of spinning
Types of spinning include ring spinning, open-end spinning, and air jet spinning.
Ring spinning: oldest method, produces high quality yarn
Open-end spinning: faster and more economical, used for coarser yarns
Air jet spinning: uses air to twist fibers together, high production rates
More about working at Reliance Industries
Top HR Questions asked in Wells Fargo
Interview Process at Wells Fargo
Top Interview Questions from Similar Companies
Reviews
Interviews
Salaries
Users/Month